Hearth & Home LOGS-NDI35 User manual

1
Hearth & Home Technologies • LOGS-NDI35 Log Instructions • 2224-935 Rev. C • 2/18
Log Set Assembly: LOGS-NDI35
Models: NDI35, NDI35-SP, NDI35-C, HNGINS-35-SP
LOG PLACEMENT INSTRUCTIONS
CAUTION: Logs are fragile, handle with care. Log #1 (SRV2224-701) Position Log #1 as shown in Figure 3. Note additional
references in Figure 2. Set the log on the log support. Ensure the log is pushed back so that the log touches the back of the
rebox. The log should be centered with the burner.
Figure 2.
LOG SUPPORT
Figure 3. Install Log #1
Figure 4. Log #2 Figure 5. Log #2
Log #2 (SRV2224-706): Position Log #2 as shown in Figure 4. Refer to Figure 2 and Figure 5 for additional details. Mate
the slot located on the bottom of Log #2 with the left log pin located on the burner top. Rotate the left end of Log #2 forward
until it comes into contact with the left grate tine.
GRATE TINES
LOG PINS
BASE TINE
LOG CONTACTS
LEFT GRATE TINE
LOG PIN
MATES WITH
LOG SLOT
2
SRV2224-701
SRV2224-704
SRV2224-703 SRV2224-702
SRV2224-706 SRV2224-705
SLOT
Figure 1. Log Set Installed
1
FLAT SPOT
FOR LOG #4
FLAT SPOT
FOR LOG #6
FLAT SPOT
FOR LOG #5

Hearth & Home Technologies • LOGS-NDI35 Log Instructions • 2224-935 Rev. C • 2/182
Log #4 (SRV2224-703): Position Log #4 as shown in Figure 8. See Figure 2 and Figure 3 for additional details. Place
the top end of log #4 on the at spot of Log #1. Position Log #4 so the groove located on the right side of the forked end
contacts the left grate tine.
Log #5 (SRV2224-704): Position Log #5 as shown in Figure 9. See Figures 2, 3 and 6 for additional details. Position the
top end of Log #5 on the at spot of Log #1. Place the forked end of Log #5 on the at spot of Log #3.
Figure 8. Log #4 Figure 9. Place Log #5
LOG SLOT
GRATE TINE SLOT
LOG RESTS ON
FLAT SPOT
LOG SLOT CONTACTS GRATE TINE
LOG RESTS ON
FLAT SPOTS
Figure 11. Log #6
BASE TINE
GROOVE
4
5
Figure 6. Log #3 Figure 7. Log #3
Log #3 (SRV2224-702): Position Log #3 as shown in Figure 6. Refer to Figure 2 and Figure 7 for location of reference
points. Mate the log slot located on the bottom of Log #3 with the right log pin located on the burner top. Rotate the right
end of Log #3 forward until it contacts with the right grate tine.
FLAT SPOT FOR
LOG #5
FLAT SPOT FOR
LOG #6
LOG PIN
MATES WITH
LOG SLOT
RIGHT GRATE TINE MATES
WITH LOG SLOT
3
Log #6 (SRV2224-705): Place the short and long points of the forked end, on the at spots of existing logs as shown in
Figure 10. See Figures 2, 3 and 6 for additional details. Position the other end of the log so it rests on the base tine. The
base tine groove will mate with the base tine See Figure 11.
Figure 10. Place Log #6
LOG RESTS ON
FLAT SPOTS
6
MATE BASE TINE
WITH LOG GROOVE