Hearth & Home LOGS-550-E User manual

1
Heat & Glo • LOGS-550-E, LOGS-750-E, LOGS-950-E Log Instructions • 2118-935 Rev. F • 10/14
Log #1: Locate the slot on the bottom right side of log 1.
Mate the slot with the right rear log tab. Pull the left end of
log #1 forward until it touches the left rear log tab.
Log Set Assembly: LOGS-550-E, 750-E, 950-E
Model: SL-550TR-E, 750TR-E, 950TR-E
SL-550TV-E, 750TV-E, 950TV-E,
SL-550TV-IPI-F, 750TV-IPI-F, 950TV-IPI-F
Left rear log tab
Left rear log tab
Lava rock retainer
Lava rock retainer
Grate tine (4)
Grate tine (4)
Log #2: Mate the far left grate tine with the notch located
on the left end of log #2. The right end of log #2 should rest
on log #1 as shown. Be sure that the top of log # 2 touches
the back of the firebox.
1
1
Mate slot with tab
Mate slot with tab
Left rear log tab
Left rear log tab
2
2
Mate notch with grate tine
Mate notch with grate tine
Figure 3
Figure 3
Figure 4
Figure 4
Figure 5
Figure 5
Right rear log tab
Right rear log tab
Shoulder screw
Shoulder screw
Log # 2 should touch firebox
Log # 2 should touch firebox
1
1
Slot
Slot
Figure 2
Figure 2
LOG PLACEMENT
INSTRUCTIONS
3/8 in.
Burner
Lava rock
retainers
PLACE LAVA ROCK
BETWEEN LAVA ROCK
RETAINERS
LAVA ROCK ZONE
Note: Figure 1 illustrates the recommended gap between the
burner and the lava rock retainer.
Figure 1
Indentation
Indentation
Indentation
Indentation
SL-550TR-E
SL-550TV-E
SL-550TV-F
SL-750TR-E
SL-750TV-E
SL-750TV-F
SL-950TR-E
SL-950TV-E
SL-950TV-F
Log 1 SRV2115-701 SRV2118-701 SRV2121-701
Log 2 SRV2115-702 SRV2118-702 SRV2121-702
Log 3 SRV2115-703 SRV2118-703 SRV2118-703
Log 4 SRV2115-704 SRV2118-704 SRV2121-704
Log 5 SRV2115-705 SRV2118-705 SRV2121-705
Carefully remove the logs from the packaging.
CAUTION: LOGS ARE FRAGILE! Handle with care.

Heat & Glo • LOGS-550-E, LOGS-750-E, LOGS-950-E Log Instructions • 2118-935 Rev. F • 10/142
Figure 8
Figure 8
Bump
Bump
Log #4: Locate the notch at the end of log # 4. Mate the
notch with the tine as shown above. The top end of log #4
should rest between the end of log #2, and the bump located
on log #1. Swing the knot on log # 4 towards log #3.
4
4
Swing knot towards log #3
Swing knot towards log #3
Mate notch with grate tine
Mate notch with grate tine
Figure 9
Figure 9
Log #5: Locate the notch at the end of log # 5. Mate the
notch with the far right grate tine. The top end of log # 5
should rest on the right side of the “bump” as shown above.
You may need to move log #4 slightly.
5
5
Bump
Bump
Mate notch with grate tine
Mate notch with grate tine
Lava Rock
Lava Rock
Figure 10
Figure 10
Step #6:Apply the supplied lava rock as shown above. Place
an even layer of lava rock in zone shown in Figure 1. The
amount should be just enough to cover the metal surface.
Take care to ensure that no lava rock is placed outside the
zone indicated in Figure 1.
Log should touch lava rock retainer
Log should touch lava rock retainer
Figure 7
Figure 7
Log #3: Locate the pin hole on the underside of log #3.
Mate the pin hole with the shoulder screw located on the
burner top. Push the left end of log # 3 toward the back of
the firebox until it touches the lava rock retainer.
3
3
Mate shoulder screw with pin hole
Mate shoulder screw with pin hole
3
3
Figure 6
Figure 6
Pin hole
Pin hole
WARNING
RISK OF EXPLOSION!
• Place lava rock according to instructions.
• Do NOT place lava rock on burner top.
• Do NOT place lava rock in a position that they may
fall into pilot area.
• Improperly placed lava rock interferes with proper
burner operation.
Delayed ignition could occur.
• Use ONLY Hearth & Home Technologies-approved
lava rock.
• Some models may not require use of entire contents
of bag.