Hearth & Home XLR-LOGS User manual

1
Hearth & Home Technologies • XLR-LOGS Installation Instructions • 2198-930 Rev. i • 6/16
CAUTION: Logs are fragile.
INSTALLATION
Note: ULPG gas is only approved for appliances in Europe,
Australia and New Zealand.
1. Removexedglassassemblybyunlatchingthetopleft
andrightspringlatches.Allowthexedglassassembly
totiltawayfromthereplaceandliftthexedglassas-
semblyupandoutoftheopening.
2. Removethemediatraybyremovingfourscrews
locatedonthefrontandrearedgesedge.SeeFigure
1.
Figure 2. Base Pan and Burner Assembly Removal
3. Remove base pan by removing 4 screws. Remove
burner assembly by removing two screws that secure
theburnertothepilotassemblybracket.SeeFigure2.
4.Adjustshuttersettingonnewburner.SeeTable1or2.
XLR-LOGS
MODEL: XLR-PLUS-AU, XLR-PLUS-AUB
• Installation Instructions •
REMOVE 4 SCREWS
REMOVE 4 SCREWS
REMOVE 2 SCREWS
BASE PAN
Figure 1. Remove Media Tray
CAUTION! Risk of Cuts or Abrasions. Wear protective
gloves and safety glasses during installation.
Leavethismanualwithpartyresponsibleforuseand
operation.
Kit Components:
• LogBurnerAssembly
• Ceramic Logs (6)
• LavaRock(1bag)
• Instructions
5. Replacestandardburnerwithlogburnerthatisincluded
withlogkitbysecuringtheburnertothepilotbracket
withtwoscrews.Re-installbasepanwith4screws.
Table 2 - Shutter Settings: XLR-PLUS
AU NZ
NG 13 mm 13 mm
ULPG FullOpen FullOpen
Figure 4. Log Tabs
7. Locatelogtabsinthemediatrayandbendthemoutto
90ºangle.SeeFigures4.
8. Reinstallmediatrayandsecurewithfourscrews.

Hearth & Home Technologies • XLR-LOGS Installation Instructions • 2198-930 Rev. i • 6/162
9. Installrightrearlog#1.Locatelogbetweentwolocat-
ingtabs.Ensurelogtstightlybetweenthetwolocating
tabs.SeeFigure6.
Figure 6. Log #1 (2111-700)
1
10. Install right front log #2. The front left side of log 2
should not extend past the locating tab.  Front edge
oflog#2shouldtouchfrontedgeofmediatray.See
Figure7.
Figure 7. Log #2 (2111-702)
2
4
11.Installleftrearlog#3.Rightsideoflog#3shouldtouch
thelocatingtab.Keepleftendoflog#3pushedback.
SeeFigure8.
Figure 9. Log #4 (2081-172)
12. Installfrontlog#4.Rightendoflogshouldtouchlocat-
ingtabandtheleftsideoflogshouldrestuponlog#3
andtouchthelocatingtabsontheleft.SeeFigure9.
Figure 10. Log #5 (330-704)
5
13. Installfrontlog#5.Positionlogbetweentwolocating
tabsandrestlogonlog#4.SeeFigure10.
LOCATING TAB
LOGCONTACTSMEDIATRAY
LOCATING TABS
LOCATINGTAB
1
2
3
4
56
Figure 5. Kit Components
LAVA ROCK
Figure 8. Log #3 (571-705)
3

3
Hearth & Home Technologies • XLR-LOGS Installation Instructions • 2198-930 Rev. i • 6/16
Figure 11. Log #3 (2111-701)
6
14.Installcenterlog #6.Placelogbetweentwolocating
 tabs. Left and right legs of log will touch media tray.
SeeFigure11.
Figure 12. Lava Rock (4021-296) No Lava Rock on Burner - See
Hatched Area
Lava Rock
15. InstalllavarockontopofmediatrayasshowninFigure
12.DONOTinstalllavarockontheburnerassembly
orinapositionwhereitmayfallintotheburnerassem-
blyarea(seehatchedarea).DONOTplacelavarock
behindrearlogs.
PleasecontactyourHearth&HomeTechnologiesdealerwithany
questions or concerns.
ForthelocationofyournearestHearth&HomeTechnologiesdealer,
pleasevisitwww.reside.com.
Hearth&HomeTechnologies
7571215thStreetWest,Lakeville,MN55044
www.reside.com
WARNING! Risk of Delayed Ignition! DO NOT place lava
rock on burner assembly. Place only on top of media tray.
Fireplace will not function properly. Delayed ignition may
occur.
LOCATING TABS