Heat & Glo 6000G User manual

1 Heat & Glo • Arcadia, Chateau, Valencia Doors • 2101-931 Rev. E • 5/11
Arcadia and Chateau Doors
Models: 6000G, 6000GL, 60000GLX, BE-41C
- Installation Instructions -
Figure 3.
Remove all materials from the packaging. It is very impor-
tant to know what kind of finishing materials are going to
be used on the fireplace. The doors are made to overlap
finishing material up to 1 in. thick (see Figure 1).
Figure 1. Overlap Fit Door
Thedoors canbe usedas aninside fitforfinishingmaterials
over 1 in. thick (see Figure 2). A template is available to
assist with proper sizing of the finishing material.
Figure 2. Inside fit door
DOOR
FINISHING
MATERIAL
FINISHING
MATERIAL
(Outside door width)
(Includes 1/8 in. opening each side of door)
37 in.
37-1/4 in.
ELBOW
HEAT
SHIELD
37 in.
33-3/4 in.
37-1/4 in.
34 in.
(Outside door width)
(Includes 1/8 in. opening each side of door)
DOOR
SLOTS
LOWER
VALVE
SHIELD
“J” HOOKS
UPPER
VALVE
SHIELD
For Valencia door see Pages 2-3.
1. Remove all materials from the packaging.
2. Install the black shoulder bolts into the four threaded
inserts located in the fireplace surround.
3. Installthe lowervalve shieldby screwingtwo selftapping
screws through the holes in the vanity panel into the pilot
holesinthefireplacesurround(seeFigure3).Note:When
installing the Hi/Low solenoid, bend the metal tab in the
lower valve shield up to clear the solenoid.
4. Install the valve shield by hooking the “J” hooks into the
small slots on the back side on the lower valve shield.
Cleaning Instructions for Doors
Use a microfiber cloth and Windex® Original Glass
Cleaner or 03M003 Stove Bright® Glass Cleaner to clean
the door immediately after installation to remove acids
deposited by the installer or technician. Spray the cleaner
onto the microfiber cloth and carefully wipe the entire
surface. The door should be cleaned in this manner
annually by the homeowner to remove fingerprints or
other contaminants. Once oxidation of the paint pigment
has occurred, cleaning will not restore the original color.
WARNING
This appliance has been supplied with an integral barrier
to prevent direct contact with the fixed glass panel. Do
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
HOT SURFACES!
Glassandothersurfacesarehotduring
operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
5. Hangthedoor on the four shoulderbolts.Push the door
in until it contacts the finishing material (overlap fit) or
the fireplace surround (inside fit).

2 Heat & Glo • Arcadia, Chateau, Valencia Doors • 2101-931 Rev. E • 5/11
Valencia Doors
Models: 6000G, 6000GL, 60000GLX, BE-41C, SL-36-Ultimate
- Installation Instructions -
Remove all materials from the packaging. It is very impor-
tant to know what kind of finishing materials are going to
be used on the fireplace. The doors are made to overlap
finishing material up to 1 in. thick (see Figure 1).
Figure 1. Overlap Fit Door
Thedoors canbe usedas aninside fitforfinishingmaterials
over 1 in. thick (see Figure 2). A template is available to
assist with proper sizing of the finishing material.
1. Remove all materials from the packaging.
2. Install the bolts into the four threaded inserts located in
thefireplacesurround. Putthe shoulderboltsinthelower
inserts. The phillips head bolts go in the top inserts.
3. Installthe lowervalve shieldby screwingtwo selftapping
screws through theholes in the vanitypanel into the pilot
holes in the fireplace surround (see Figure 3). Note:
When installing the Hi/Low solenoid, bend the metal tab
in the lower valve shield up to clear the solenoid.
4. Install the valve shield by hooking the “J” hooks into the
small slots on the back side on the lower valve shield.
5. Using a pliers, separate the front door panel and back
door panel by bending up the two tabs from the top “J”
hooks and lifting the front door panel to unhook. The
two tabs can be bent straight or broke off.
6. Hang the back door panel on the four bolts. Push the
door in until it contacts the finishing material (overlap
fit) or the fireplace surround (inside fit). Tighten the top
phillips bolts firmly.
7. Hang the front door panel on the back door panel by
hooking the “J” hooks through the slots in the back panel.
Figure 2. Inside fit door
DOOR
FINISHING
MATERIAL
FINISHING
MATERIAL
(Outside door width)
(Includes 1/8 in. opening each side of door)
37 in.
37-1/4 in.
ELBOW
HEAT
SHIELD
37 in.
33-3/4 in.
37-1/4 in.
34 in.
(Outside door width)
(Includes 1/8 in. opening each side of door)
For Arcadia and Chateau doors see Page 1.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
• Do NOT operate with protective barriers open or removed.
• The doors must remain closed if children will be present
during the operation of the fireplace.
• The doors may be made operable per these instructions.
Thismaybedoneonlyuponrequestofapersonresponsible
for the use and operation of the fireplace.
• The doors can be returned to the locked position following
these instructions.
• These instructions are to be left with a person responsible
for the use and operation of the fireplace.
• When the doors are in an operable state, the door-locking
screw must be retained in the threaded nut behind doors.

3 Heat & Glo • Arcadia, Chateau, Valencia Doors • 2101-931 Rev. E • 5/11
Figure 3.
BACK
DOOR
PANEL
FRONT
DOOR
PANEL
BOLTS (4)
FIREPLACE
SURROUND
VALVE
SHIELD
LOWER
VALVE
SHIELD
Cleaning Instructions for Doors
Use a microfiber cloth and Windex® Original Glass
Cleaner or 03M003 Stove Bright® Glass Cleaner to clean
the door immediately after installation to remove acids
deposited by the installer or technician. Spray the cleaner
onto the microfiber cloth and carefully wipe the entire
surface. The door should be cleaned in this manner
annually by the homeowner to remove fingerprints or
other contaminants. Once oxidation of the paint pigment
has occurred, cleaning will not restore the original color.
Please contact your Heat & Glo dealer with any
questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
Heat & Glo, a brand of Hearth & Home Technologies Inc.
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
8. To unlock the doors and make them operable.
When the front door panel is off the fireplace, locate the
lockingbar boltedunder twoacornnuts.Removeoneofthe
acorn nuts and rotate the locking bar to a vertical position.
Replace the acorn nut. Hook the front door panel on the
fireplace following the above steps.