Heat & Glo LOGS-I35FB User manual

1
Heat & Glo • LOGS-I35FB Log Instructions • 2202-935 Rev. F • 5/18
LOG PLACEMENT INSTRUCTIONS
CAUTION: Logs are fragile, handle with care.
Figure 1. Log Set Installed Figure 2. Reference Points
PILOT BRACKET
GRATE
BAR
GRATE TINES
BURNER LEDGE BURNER LEDGE
LIGHT TRAYS
SRV2202-702
SRV2202-704
SRV2202-706
SRV2202-701
SRV2202-703
SRV2202-705
LOG PINS
Log #1 (SRV2202-702): See Figure 2 for additional references. Position Log #1 as shown in Figure 3. Rest the left and
right ends of Log #1 on the burner ledge. The pilot bracket will support the center of the log. Pull the left end of the log
forward into position.
Figure 3. Log #1
LOG RESTS ON
PILOT BRACKET
REST LOG ON
BURNER LEDGE
FLAT SPOT
FOR LOG #5
1
5
12
6
4
3
1
2
3
4
56
Log Set Assembly: LOGS-I35FB
Models: ESCAPE-I35FB, ESCAPE-I35-C, ESCAPE-I35-F, ESCAPE-35-IFT

Heat & Glo • LOGS-I35FB Log Instructions • 2202-935 Rev. F • 5/182
Log #3 (SRV2202-704): See Figure 2 for additional reference details. Locate the log slot on the bottom right end of Log
#3. Mate the log slot with the left log pin. Rotate the left end of the log counterclockwise, until it contacts the grate tine.
Log #4 (SRV2202-703): See Figure 2 for additional reference details. Locate the log slot on the bottom left end of log #4.
Mate the log slot with the right log pin. Rotate the right end of the log clockwise, until it contacts the grate tine.
Figure 5. Log #3 Figure 6. Log #4
34
Log #2 (SRV2202-701): See Figure 2 for additional references. Position Log #2 as shown in Figure 4. Mate Log #2 with
the right corner of the burner as shown. Pull the log forward and to the left until it locks into position.
LOG CONTACTS LEFT
GRATE TINE
LOG CONTACTS RIGHT
GRATE TINE
FLAT SPOT
FOR LOG#6
Figure 4. Log #2
LOG HANGS OVER
ONTO BURNER TOP
2
1
Figure 7. Glass Rock in Place
GLASS ROCK
LOG MATES
WITH CORNER
OF BURNER
Glass Rock (2201-853): Once Log #3 and Log #4 are installed, ll each light tray with the glass rock.
WARNING! Risk of Explosion! DO NOT place glass rock on the burner surface. DO NOT place glass rock directly over
burner ports. Improperly placed glass rock interferes with proper burner operation.

3
Heat & Glo • LOGS-I35FB Log Instructions • 2202-935 Rev. F • 5/18
Figure 8. Place Log #5
Figure 9. Place Log #6
Log #5 (SRV2202-705): See Figures 2 and 3 for additional references. Place the thick end of Log #5 on the at spot of
Log #1. Locate the groove on the thin end of the log. Mate the groove with the grate bar as shown above. Center the tip
of Log #5 between the ends of Log #3 and Log #4.
5
6
PLACE LOG
ON FLAT SPOT
FLAT SPOTS
FOR LOG #6
PLACE LOG
ON FLAT SPOT
PLACE LOG
ON FLAT SPOT
Log #6 (SRV2202-706): See Figures 2 and 8 for additional references. Place the thick end of the log on the at spot of Log
#2. Place the thin end of Log #6 on the at spot of Log #5 as shown in Figure 9.
GROOVE MATES
WITH GRATE BAR
CENTER
BETWEEN
LOG #3 AND
LOG #4