Heat & Glo PORTRIM6-BR User manual

1Heat & Glo • 2595-931 Portrait Trim Instructions • 2595-931 • 5/22
Portrait Decorative Front Trim
PORTRIM6-BR / CO / NI, PORTRIM8-BR / CO / NI
For use only with Heat & Glo Portrait Decorative Fronts:
PORTRAIT-6-BK, PORTRAIT-8-BK- Installation Instructions -
Leave this manual with party responsible for use
and operation.
CAUTION! Risk of Cuts, Abrasions. Wear protective
gloves and safety glasses during installation. Metal edges
are sharp.
CAUTION! Do not install damaged components.
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and must be installed for
the protection of children and other at-risk
individuals.
Figure 1
Installation Instructions
1. While wearing protective gloves, remove trim pieces
from packaging. The mitered ends are sharp. Lay the
trim pieces out on the floor. The longer pieces are for
the top/bottom and the shorter pieces are for the sides.
See Figure 1.
2. Remove the Portrait decorative front from the appli-
ance.
Preparation
CAUTION! Risk of Burns!
• The fireplace should be turned offand cooled before
trim is installed on decorative barrier front.
• Shut offgas supply.
Contents:
Portrait Trim Pieces
Tools Needed:
Rubber Mallet
NOTICE: Trim pieces are easily scratched. Handle with
care.
NOTICE: Once trim pieces are installed, they can only be
removed by disassembling the decorative front.
TOP
SIDE
SIDE
BOTTOM
SIDE PROFILE DETAIL
FRONT
VISIBLE
EDGE
BACK EDGE (SCREEN SIDE)
Note: The trim installation process is made easier by po-
sitioning the decorative front so that the side to which the
trim is being added is on the floor. The order of instal-
lation is top, side, side and the bottom piece should be
installed last.

2Heat & Glo • 2595-931 Portrait Trim Instructions • 2595-931 • 5/22
Figure 2
4. Repeat step 3 for the left and right sides of the front.
5. To install the bottom piece, hold the trim by the ends
with the front edge facing you. Slightly bow the trim
piece so that you can engage the left and right ends
under the bottom of the left and right trim pieces. Be
careful not to scratch the trim or the decorative front.
Once in place, lightly tap it with a rubber mallet to snap
it into place. See Figure 3.
6. Ensure all of the trim pieces are fully seated with an
even reveal as illustrated in Figure 3. To remedy an
uneven reveal, place an object with a blunt edge, such
as a block of wood, and tap lightly in order to seat the
trim piece.
7. Install the Portrait Decorative front, complete with trim,
on the appliance according to the instructions included
with the decorative front.
Figure 3
Cleaning Instructions for Decorative Fronts and Trim
Use a microfiber cloth and Windex® Original Glass
Cleaner to clean the decorative front immediately after
installation to remove acids deposited by the installer or
technician. Spray the cleaner onto the microfiber cloth
and carefully wipe the entire surface. The decorative
front should be cleaned in this manner annually by the
homeowner to remove fingerprints or other contaminants.
Once oxidation of the finish has occurred, cleaning will
not restore the original color.
Please contact your Heat & Glo dealer with any
questions or concerns.
For the location of your nearest Heat & Glo dealer,
please visit www.heatnglo.com.
Heat & Glo, a brand of Hearth & Home Technologies
7571 215th Street West, Lakeville, MN 55044
www.heatnglo.com
3. Install the top trim piece by placing it over the inner
edge of the front. Hook the back of the trim over the
base extrusion and then rock it forward. Lightly tap it
with a rubber mallet to snap into place, starting in the
middle and working toward the sides. See Figure 2.
Place left and right ends in position
Fully Seated - Even Reveal Not Fully Seated - Uneven Reveal
PORTRAIT
DECORATIVE
FRONT
PORTRAIT
DECORATIVE TRIM
ASSEMBLED SIDE PROFILE DETAIL
MESH