Heat & Glo LOGS-I35 User manual

1
Heat & Glo • LOGS-I35 Log Instructions • 2205-935 Rev. C • 7/11
Log Set Assembly: LOGS-I35
Models: GRAND-I35, GRAND-I35-SP, GRAND-I35-C
LOG PLACEMENT INSTRUCTIONS
CAUTION: Logs are fragile, handle with care.
Figure 1. Log Set Installed Figure 2. Reference Points
Figure 3. Log #1 Figure 4. Log #1
MATE TINE
MATE TINE
WITH LOG
WITH LOG
GROOVE
GROOVE
Log #1 (SRV2205-702) Position Log #1 as shown in Figure 3. Mate the left grate tine with the log groove. Rest the nose of
the log on the log support as shown.
REST LOG #6
REST LOG #6
HERE
HERE
REST LOG #5
REST LOG #5
HERE
HERE
REST NOSE
REST NOSE
OF LOG ON
OF LOG ON
LOG SUPPORT
LOG SUPPORT
LOG NOSE
LOG NOSE
1
SRV2205-702
SRV2205-702
SRV2205-704
SRV2205-704
SRV2205-701
SRV2205-701
SRV2205-710
SRV2205-710
SRV2205-703
SRV2205-703
SRV2205-705
SRV2205-705
SRV2205-706
SRV2205-706
#2
#1
#3
#5
#6
#7
#4
LOG SUPPORT
GRATE TINES

Heat & Glo • LOGS-I35 Log Instructions • 2205-935 Rev. C • 7/112
Log #3 (SRV2205-705): Position the log groove with the 2nd grate tine from the right. Rotate the right end of the log
clockwise until the end of the log contacts the grate bar.
Figure 7. Log #3 Figure 8. Log #3
Figure 9. Place Log #4 Figure 10. Place Log #5
FLAT SPOT
FLAT SPOT
FOR LOG #7
FOR LOG #7
LOG GROOVE
LOG GROOVE
CONTACTS
CONTACTS
GRATE TINE
GRATE TINE
LOG CONTACTS
LOG CONTACTS
GRATE BAR
GRATE BAR
LOG GROOVE
LOG GROOVE
FLAT SPOT FOR
FLAT SPOT FOR
GRATE BAR
GRATE BAR
FLAT SPOT FOR
FLAT SPOT FOR
LOG #6
LOG #6
LOG GROOVE
LOG GROOVE
CONTACTS
CONTACTS
GRATE TINE
GRATE TINE
END OF LOG RESTS
END OF LOG RESTS
ON FLAT SPOT
ON FLAT SPOT
LOG RESTS ON
LOG RESTS ON
FLAT SPOT
FLAT SPOT
LOG NOTCH
LOG NOTCH
CONTACTS
CONTACTS
GRATE TINE
GRATE TINE
3
45
Figure 5. Log #2 Figure 6. Log #2
Log #2 (SRV2205-701): Position Log #2 as shown in Figure 5. Mate the right grate tine with the log groove. Rest the back
of the log on the log support. Rotate the back of the log clockwise until the foot contacts the vertical wall of the log support.
FLAT SPOT FOR LOG #4 AND LOG #7
FLAT SPOT FOR LOG #4 AND LOG #7
LOG FOOT
LOG FOOT
CONTACTS
CONTACTS
LOG SUPPORT
LOG SUPPORT
LOG FOOT
LOG FOOT
SURFACE
SURFACE
CONTACTS
CONTACTS
LOG SUPPORT
LOG SUPPORT
2
MATE TINE WITH
MATE TINE WITH
LOG GROOVE
LOG GROOVE
Log #4 (SRV2205-704): Position Log #4 so that the log groove contacts the second grate tine from the left, as shown in
Figure 9. Set the other end of the log on the flat spot located on Log #2. See Figure 5.
Log #5 (SRV2205-710): Mate the notch on Log #5 with the second grate tine from the left as shown in Figure 10. Set the
other end of the log on the flat spot of Log #1. See Figure 3.

3
Heat & Glo • LOGS-I35 Log Instructions • 2205-935 Rev. C • 7/11
Figure 11. Log #6 Figure 12. Log #7
LOG #6 RESTING ON
LOG #6 RESTING ON
FLAT SPOTS
FLAT SPOTS
LOG #7 RESTING ON
LOG #7 RESTING ON
FLAT SPOTS
FLAT SPOTS
Log #6 (SRV2205-706): Position Log #6 as shown in Figure 11. Ensure that the correct end of the log rests on the flat
spots. The thicker end points forward. Locations of flat spots are indicated in Figure 3 and Figure 9.
Log #7 (SRV2205-703): Position Log #7 as shown in Figure 12. Position the point of the log on the flat spot of Log #3.
Place the wider end of the log on the flat spot of Log #2. See Figure 5 and Figure 7 for locations of flat spots.
67