Henny Penny ODS-450 User manual

OPERATOR’S
MANUAL
REGISTER WARRANTY ONLINE AT WWW.HENNYPENNY.COM
OIL DISPOSAL SHUTTLE (Electric)
MODEL
ODS-450

TABLE OF CONTENTS
Section Page
Section 1. INTRODUCTION ............................................................................................................1-1
1-1. Introduction.............................................................................................................1-1
1-2. Features...................................................................................................................1-1
1-3. Proper Care .............................................................................................................1-1
1-4. Assistance ...............................................................................................................1-1
1-5. Safety ......................................................................................................................1-2
Section 2. ASSEMBLY.....................................................................................................................2-1
Section 3. OPERATION WITH EVOLUTION ELITE OPEN FRYERS.........................................3-1
Section 4. OPERATION WITH 500 & 600 PRESSURE FRYERS .................................................4-1
Section 5. DISPOSING OF OIL INTO DISPOSAL CONTAINER.................................................5-1
Section 6. PART INFORMATION ...................................................................................................6-1
6-1. Introduction.............................................................................................................6-1
6-2. Genuine Parts..........................................................................................................6-1
6-3. How to Order ..........................................................................................................6-1
6-4. Prices.......................................................................................................................6-1
6-5. Delivery...................................................................................................................6-1
6-6. Warranty .................................................................................................................6-1
6-7. Recommended Spare Parts for Distributors............................................................6-1
Wiring Diagram
I 811

ODS-450
Where information is of particular importance or is safety
related, the words NOTICE, CAUTION, or WARNING are
used. Their usage is described below:
SAFETY ALERT SYMBOL is used with DANGER,
WARNING, or CAUTION which indicates a personal
injury type hazard.
NOTICE is used to highlight especially important
information.
CAUTION used without the safety alert symbol
indicates a potentially hazardous situation
which, if not avoided, may result in property damage.
CAUTION used with the safety alert symbol
indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderate injury.
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury.
DANGER INDICATES AN IMMINENTLY
HAZARDOUS SITUATION WHICH, IF NOT
AVOIDED, WILL RESULT IN DEATH OR
SERIOUS INJURY.
811 1-1
SECTION 1. SAFETY

ODS-450
2-1 811
SECTION 2. ASSEMBLY
USING BOLTS & NUTS
PROVIDED, ATTACH
HANDLE TO SHUTTLE.
USING PIPE THREAD SEALANT, THREAD
THE HOSE INTO PUMP AND ATTACH
QUICK DISCONNECT TO SHUTTLE
HANG THE PRESSURE FRYER “FUNNEL”
& POWER CORD ON HANDLE
READY FOR USE

ODS-450
1. Open the door, lift-up on the drain pan stop and pull-out
the drain pan assembly, using the handle on the drain
pan. Figures 1 & 2.
2. Release cover latch, and hinge back cover on oil
disposal shuttle. Figure 3. Make sure crumb catcher is
in place.
3. Roll oil disposal shuttle under fryer until it stops. Make
sure drain aligns with opening in shuttle. Figure 4.
TO AVOID PERSONAL INJURY, BURNS,
SPILLS, AND CORROSION:
DO NOT OVERFILL. SHUTTLE HOLDS
OIL FROM ONE FULLSIZE VAT OR
TWO SPLIT VATS ONLY
DO NOT PUT WATER AND/OR
CLEANER IN THE SHUTTLE
OIL ONLY
DO NOT TRANSPORT OIL WITHOUT
COVER IN PLACE
4. Using the fryer controls, press and hold (on either
side) until display shows *FILTER MENU*, along
with “1.EXPRESS FILTER”.
5. Press and release twice until display shows
“3.DISPOSE”. Press √button and display shows
“DISPOSE?” along with “YES NO”.
To reduce the risk of fire or electrical shock, do not
empty more than one full vat or two split vats at one
time.
811 3-1
SECTION 3. OPERATION WITH EVOLUTION ELITE OPEN FRYERS
Figure 1
Figure 2
Figure 3
Figure 4

ODS-450
6. With discard shuttle rolled into place, press √
button and display shows “OPEN DRAIN”. Pull-out
on drain knob to open drain and display shows
“DRAINING”. Oil now drains from the vat into the
shuttle.
If oil disposal shuttle is not properly in place,
“IS DISPOSAL UNIT IN PLACE?” shows in display.
Adjust the bracket on the front of the shuttle as needed
by loosening the 4 nuts securing the bracket and
moving the bracket up or down. Once properly
adjusted, the display shows “DRAINING”. Figure 5.
7. Display shows “VAT EMTY”, along with “YES NO”.
Verify that vat is empty, and press √button.
8. Display shows “CLN VAT COMPLETE”, along with
“YES NO”. Once vat is clean, press √button and close
drain.
9. Display shows “MANUAL FILL POT”, followed by
“VAT FULL”, along with “YES NO”. Fill the vat to
the lower indicator line on the rear of the vat and then
press √ button. Controls return to normal operation.
3-2 811
Figure 5

ODS-450
1. Move the fryer main power switch to the OFF position.
2. Remove and empty the condensation drain pan.
3. Disconnect the filter union and remove the drain pan
from under the frypot.
The filter union could be hot! Use protective cloth
or glove, or severe burns could result.
4. Release cover latch, and hinge back cover on oil
disposal shuttle. Figure 2. Make sure crumb catcher is
in place.
5. Using the “funnel” on the back of the handle, place it
over the opening of the shuttle. Figure 3.
6. Roll oil disposal shuttle under fryer until the stop
brackets on both sides of the shuttle contacts the frame.
Figure 4. This assures drain aligns with opening in
shuttle.
TO AVOID PERSONAL INJURY, BURNS,
SPILLS, AND CORROSION:
DO NOT OVERFILL. SHUTTLE HOLDS
OIL FROM ONE FULLSIZE VAT OR
TWO SPLIT VATS ONLY
DO NOT PUT WATER AND/OR
CLEANER IN THE SHUTTLE
OIL ONLY
DO NOT TRANSPORT OIL WITHOUT
COVER IN PLACE
7. Turn drain handle and drain oil into shuttle.
811 4-1
SECTION 4. OPERATION WITH 500 & 600 PRESSURE FRYERS
Figure 1
Figure 2
Figure 3
Figure 4

ODS-450
1. Remove the oil disposal shuttle from under fryer and
replace with the filter pan assembly.
2. Close the cover on shuttle and roll oil disposal shuttle
to disposal container.
3. Press down on top of brake to secure unit in place.
Figure 1.
4. Disconnect fitting from top of ODS and connect to
disposal container. Figure 2.
5. Using the power cord on the back of the shuttle handle,
plug it into the short cord from the junction box.
Figures 3 & 4
6. Turn power switch to the ON position. Figure 4.
5-1 811
Figure 2
Figure 3
SECTION 5. DISPOSING OF OIL INTO DISPOSAL CONTAINER
Figure 1
Figure 4
Press down to lock
Press to release

ODS-450
7. Plug the shuttle electrical cord into the receptacle under
the disposal container control, and then press & hold
switch on container controls to pump oil from shuttle
to the container. Figure 5.
8. Once shuttle is empty, release switch and unplug the
electrical cord and wrap back onto the hook on the
shuttle handle.
9. Using gloves or protective cloth, disconnect the fitting
from the disposal container and connect it back onto the
shuttle. Figure 6.
Disconnect fitting could be hot! Use protective cloth
or gloves when disconnecting fitting, or severe burns
could result.
CLEANING
Daily, remove the crumb catcher (Figure 6) and take it
to a sink and clean with soap and water. Clean the
exterior of the shuttle with a soft cloth and soap and
water. It’s not necessary to clean the interior of the
unit, but if desired, it can be wiped down with paper
towels.
To avoid damage to pump, do not use water or
water-based liquids to clean the interior of the shuttle.
811 5-2
Figure 5
Figure 6
Figure 7

ODS-450
6-1. INTRODUCTION This section identifies and lists the replaceable parts of the Henny
Penny Oil Disposal Shuttle.
6-2. GENUINE PARTS Use only genuine Henny Penny parts in your unit. Using a part of
lesser quality or substitute design may result in unit damage or
personal injury.
6-3. HOW TO FIND PARTS To find items you want to order from the Parts List, proceed as
follows:
1. Refer to the exploded drawing in this section to identify the part
needed.
2. Use the item number from the exploded drawing to locate the
corresponding part in the parts list in this section. In this list will
be the Henny Penny part number and description of the part.
6-4. HOW TO ORDER PARTS Once the part you want to order has been found in the Part List,
write down the following information:
1. From the exploded drawing and Parts List (Sample)
Item Number 15
Part Number 77815
Description WHEEL – 8 INCH – ODS
2. From the data plate (Sample)
Serial Number 00100
6-5. PRICES Your distributor has a price parts list and will be glad to inform you
of the cost of yours parts order.
6-6. DELIVERY Commonly replaced items are stocked by your independent Henny
Penny distributor and will be sent out when your order is received.
Other parts will be ordered by the distributor from Henny Penny
Corporation. Normally, these will be sent to your distributor within
three working days.
6-7. WARRANTY All replacement parts (except lamps and fuses) are covered under
warranty for 90 days against manufacturing defects and workman-
ship. If damage occurs during shipping, notify the carrier at once so
that a claim may be properly filed. Refer to the warranty in this
manual for other rights and limitations.
Recommended replacement parts are indicated with A or B in the
parts lists:
A = parts to be stocked on service vans or trucks
B = parts to be stocked at the distributor/KES location.
Inventory on all other parts not identified, should be based upon
usage in the territory. Please use care when ordering recommended
parts, because all voltages and variations are marked. Distributors
should order parts based upon common voltages and equipment
sold in their territory.
6-1 811
SECTION 6. PARTS INFORMATION
6-8. RECOMMENDED
SPARE PARTS FOR
DISTRIBUTORS

ODS-450
811 6-2
1
2
3
5
11
12
7
13
14
15
16
17
19
24
18
20
22
23
21
24
8
26
25
10
9
31
4
6
7
28
29
30
27
32
33
34
35
36
37
38
39

ODS-450
Item Part
Number Number Description Qty
B1 21753 ASSY – FILTER HOSE ODS 1
Β2 21612 DISCONNECT - FEMALE 1
3 69356 PUMP & MOTOR ASSY 1
Β3 67583 MOTOR, 1/2 HP - 50/60 Hz 1
Β4 17437 PUMP ASSEMBLY 1
5 FP02-060 NIPPLE – ¾ CLOSE SS 1
6 MS01-583 GROMMET – HIGH TEMP FLEXIBLE 1
7 88302 NIPPLE – DOLLY OIL PICK UP 1
8 88295 BRACKET – CORD HANGER 1
9 91044 BRACKET – ODS FUNNEL HANGER 1
Β10 88746 FUNNEL – ODS – 500/600 1
11 84001 ASSY -- COVER ODS DRAIN PAN DOLLY 1
12 83993 HINGE 2
* SC01-113 SCREW--#6-32 X 9/16 PHILLIPS, PAN HD 4
* NS02-005 NUT--HEX--KEPS #6-32 4
13 84519 BRACKET – DRAIN SW ENGAGEMENT LV 1
Β14 84453 BASKET – CRUMB 1
Β15 19004 CASTER 2” SWIVEL PLATE 2
16 88707 WELD ASSY – ODS DRAIN PAN DOLLY 1
Β17 77815 WHEEL – 8 INCH – ODS 2
Β18 21611 DISCONNECT – MALE 1
Β19 84614 SEAL – COVER 1
A20 MS01-532 LATCH 1
20* SC01-049 SCREW--#6-32 X 3/8 PHILLIPS, PAN HD 2
20* NS02-005 NUT--HEX--KEPS #6-32 2
20* 83994 BRACKET-LATCH MOUNTING 1
21 SC06-074 SCREW – ½ x 1-1/2 SHOULDER 2
22 LW01-010 LOCKWASHER – SPLIT-RING 3/8 S 2
23 NS01-001 NUT – HEX 3/8-16 2
24 NS02-006 NUT – HEX – KEPS #10-24 C 23
25 NS02-002 NUT – HEX – KEPS 1/4-20 C 4
26 SC01-057 SCREW – ¼-20 x ½ HEX HD C 4
Β27 88331-01 ASSY – PLUG & CORD 125V – 15A 1
28 42512 PLUG – 125V – NEMA L5-15P 1
29 MS01-139 CABLE - #16/3 BLACK 90C JACKET 8 FT
30 91064 RECEPTACLE – STR BLADE 15A-125V 1
31 84368 WELD ASSY – DOLLY HANDLE 1
Β32 92664 ASSY – 6 IN. CORD – 15A-125V 1
33 92663 POWER CORD – 6 IN. 1
34 92658 PLUG – 15A-125 – NEMA 5-15P 1
35 92662 BOOT – WEATHER PROOF 1
36 92009 BRAKE – ODS DOLLY 1
A37 72277 SWITCH – POWER SPLASH PROOF 1
38 21635 COVER – JUNCTION BOX 1
39 23459 BOX – JUNCTION 1
Recommend Parts: A=Truck Stock/B=Dist. Stock
*not shown
6-3 811

ODS-450
FILTER MOTOR AND PUMP
Item Part Description Per
No. Number Assy
Β 1 67583 MOTOR, 1/2 HP - 50/60 Hz 1
Α 2 17476 SEAL KIT 1
3 17437 PUMP ASSEMBLY 1
4 SC01-132 SCREW, Pump Cover 1
5 17451 COVER, Pump 1
Β 6 17447 ROTOR, Pump 1
Α 7 17446 ROLLER, Pump 5
Α 8 17453 O-RING 1
9 17454 BODY, Pump 1
10 17456 SHIELD, Pump 2
11 SC01-026 SCREW, Pump Shield 1
Recommend Parts: A=Truck Stock/B=Dist. Stock
811 6-4

ODS-450

ODS-450

Henny Penny Corporation
P.O.Box 60
Eaton, OH 45320
1-937-456-8400
1-937-456-8402 Fax
Toll free in USA
1-800-417-8417
1-800-417-8434 Fax
www.hennypenny.com
*FM05-065-B* Henny Penny Corp., Eaton, Ohio 45320, Revised 6-25-13