Honeywell Domonial User manual

EKZ008200B
10/2007
© 2007 Honeywell International Inc.
Domonial
User manual
Manuel d’utilisation
Manual de uso
Manuale dell'utente
Benutzerhandbuch
Gebruikershandleiding
EKZ r B:

1- INTRODUCTION TO THE SECURITY SYSTEM 2
2- INDICATOR LIGHTS 3
3- UNDERSTANDING THE SYSTEM TONES 4
4- HOW TO USE THE WIRELESS KEYPAD WITH DISPLAY 5
5- HOW TO USE THE WIRELESS KEYPAD WITH PROX READER 9
6- HOW TO USE THE KEYFOB WITH 1 LED 12
7- HOW TO USE THE KEYFOB WITH 3 LEDS 13
8- HOW TO CONTROL YOUR SYSTEM OVER THE PHONE 15
9- MAINTENANCE AND RECOMMENDATIONS 16
Congratulations on your purchase of the
Honeywell Domonial security system.
To make the best out of your system we advise
you to read this manual carefully.
This security system is designed to operate on
an authorised radio frequency and will in no way
endanger the user.
- 1 -
E
N
G
L
I
S
H

It may include :
•A KEYPAD WITH DISPLAY for arming and disarming operations and
access to advanced user functions like detector bypass and events log.
•A KEYPAD WITH PROX READER for all users arming and disarming
operations of the different sets.
•A KEYFOB associated to one or more users for arming and disarming
operations.
•A PIR DETECTOR, is a motion detector, which reacts to the temperature
fluctuations caused by a person in motion.
•A DOOR CONTACT, is a magnetic contact, which two parts are, fitted
one on a door frame and the other on the door itself. When the door or
window is open, the detector is triggered. Before leaving the premises,
always make sure that all openings are properly closed.
•A GLASS BREAK DETECTOR, which analyses the various frequencies
emitted by glass being broken.
•
A SMOKE DETECTOR mounted on the ceiling, which ensures the
coverage of about 50 square metres. Refrain from smoking in the vicinity
of this detector.
•A SHOCK DETECTOR mounted on the window/door frame, which detects the
vibrations emitted when a door/window is opened or closed.
E
N
G
L
I
S
H
Radio
• Narrow band frequency modulation
• Identification code for each component
(no interference between neighbouring systems)
• Protection against attempted jamming
• Radio monitoring of the system peripherals
Electrical
• Mains supply with battery backup
• Built-in voltage surge protection
• System supply monitoring
Operational
• Up to 3 protected sets: Total set, Part set, Annex set
• Up to 30 detectors
• Alert functions
• All components protected against tampering
Transmission
• Built-in telephone transmission
• Telephone line loss detection
• Transmission monitoring by periodical tests
• Optional GSM transmitter
1- Introduction to the security system
The Domonial control panel/communicator unit is the brain of your security system. It exchanges
information with the associated wireless peripherals.
The control panel centralises the data sent by the detectors, records the arming and disarming
operations and communicates with the Alarm Receiving Centre.
The control panel also includes a speaker for alarm signalling and audio verification.
Your security system may allow up to 3 sets: total set, part set, annex set.
- 2 -

E
N
G
L
I
S
H
- 3 -
2- Indicator lights
The front cover of the control panel features LED indicators which show the status of your security
system.
1- LED INDICATOR “AC MAINS POWER”
ON:The Control Panel is supplied from the Mains.
OFF:There is a mains power failure - The control panel is supplied by
its built–in battery.
2- LED INDICATOR “SYSTEM ARMED”
ON:The system total set is armed.
OFF:The system is disarmed.
FLASHING :The system part or annex set is armed.
3- LED INDICATOR “DETECTOR ACTIVATED”
FLASHING:One of the window or door protected by a
magnetic contact is opened. It flashes until the window or door has
been closed.
4- LED INDICATOR “ALARM MEMORY”
ON:An intruder alarm occurred while the system was armed.
FLASHING:An alarm occurred while the part set or annex set
was armed.
The indicator remains ON until the next arming.
5- LED INDICATOR “TECHNICAL FAULT”
ON:A fault on a technical channel.
FLASHING:A fault on the system.
(Battery, Supervision, Tamper, Phone line failure or Radio jamming)
The indicator remains ON or FLASHING until the condition has been cleared.

3- Understanding the system tones
SIRENS
A siren is an effective deterrent due to its power and very irritating tone.
The system has a siren built in the control panel. An optional remote
siren can be added.
In addition, the panel built-in siren emits an audible confirmation
tone when arming and disarming the security system and a fire
tone when a smoke detector is triggered. The volume levels can be
adjusted by the installer.
E
N
G
L
I
S
H
SYSTEM TONES
- 4 -
TOTAL SET
ARMING
DISARMING
PART SET
ARMING
FAULT
ALERT
ENTRY DELAY
Sequence of 3 modulated sounds
When arming total set, confirms that the
control panel has received a valid code or
TAG and is preparing to arm total set.
When Disarming, confirms that the
control panel has been successfully
disarmed.
When arming the part set, confirms that
the control panel has received a valid
code or TAG and is preparing to arm part
set.
This tone indicates a fault in the system.
Confirms the transmission of an alert to
the Alarm Receiving Centre.
After you open the entry door, the entry
time starts. You should disarm your
system within this time. Beeps sound at
the end of the entry time.
Continuous beep
Sequence of 2 modulated sounds
Duration : 2,5 seconds
2 times 7 fast beeps
4 beeps in case of alert...
Upon entry...
EXIT DELAY Beeps sound at the end of the exit time
until the system is armed.
Upon arming...
One beep every second
Duration : 2,5 seconds
sent via the keypad
ANNEX SET
ARMING
Duration : 4 seconds
One beep per second

E
N
G
L
I
S
H
- 5 -
4- How to use the wireless keypad with display*
The wireless keypad with display offers a complete range of tools to manage your
alarm system, from normal operation to dedicated user functions.
The keypad is used to arm and disarm your security system using a valid access
code or key TAG. The master code or TAG is required to modify other users'
codes and TAGs.
ARMING USING YOUR CODE OR TAG
If the keypad is not in its base, please return it there (for Total or Annex set only).
Press an arming key on the keypad.
If the system diagnoses a fault on arming, a fault message is displayed. Press the
OK key or the arming key to bypass the faults and continue the arming process.
Enter a valid code or present a programmed TAG
The arming tone is emitted by the keypad and by the panel siren
(if setup).
The screen counts down the exit time remaining.
Arming is automatically completed at the end of the delay (Depends on
site configuration). The icon confirms the completion of setting.
The screen clears after a few seconds.
For total set arming, the keypad's left light indicator is on during the exit delay.
For part set arming, the keypad's right light indicator is flashing during the entire
set period.
DISARMING USING YOUR CODE OR TAG
To enable you to get to the keypad without triggering an alarm, your installer has
programmed an entry delay of 30 seconds (Depends on site configuration).
Enter a valid code or present a programmed TAG
The disarming tone is emitted by the keypad and by the panel siren
(if set up).
Disarming the system will also stop the sirens if an alarm is triggered. Stopping
the siren does not interrupt the transmission of the alarm to the ARC.
Note : Depending on the configuration of your keypad, this will disarm the total set or the
entire system. In the latter case, the annex set might need to be re-armed.
* The system may include 0 to 4 keypads of this type
Total set arming
Part set arming
TAG
4- or 6-digit code
4 or 6-digit code

E
N
G
L
I
S
H
- 6 -
DURESS CODE
A duress code can be used if you are forced to disarm your security system under
duress. Your duress code is +1 to your code (1234 => 1235, 6789 => 6780). The
system will disarm as normal however a silent alert signal is transmitted to your
Alarm Receiving Centre.
INCORRECT CODE PROTECTION
If you enter five successive incorrect codes or present five incorrect TAGs, the keypad is
blocked for 5 minutes.
SENDING A PANIC SIGNAL
You can send an instant panic alarm whenever you feel threatened whilst at home,
even when your system is not armed :
Press the “SOS” keys simultaneously.
The siren is triggered (depending on configuration).
The Alarm Receiving Centre is alerted.
KEYPAD DISPLAY
Your keypad is equipped with a display to ease access to advanced user functions and rich content.
Menu functions are only accessible when the system is disarmed.
The display icons provide a quick view of the system status.
The navigation keys are used to access the menu:
• Press the arrow keys to enter the main menu, navigate and view choices identified by
brackets “< >”,
• Press the key to confirm your choice,
• Press the Return key to abort your choice and return to the main menu.
Code + 1
Total set armed
Part set armed
Annex set armed
System disarmed
Annex set disarmed
Receiver 1 ON
Receiver 2 ON
Radio transmission in progress
Silent mode
Unread message
Detector activated
Tamper fault
System fault
Bypassed detector
Power supply fault
State of keypad battery
Blinking = replace battery

STATUS SCREEN
When the keypad is turned off, you can view the current status of the system by pressing OK.
This will display icons and fault messages if any.
SETTINGS MENU
When the system is disarmed, you can access the menu to modify the various
settings of your system.
• The system can have up to 10 users. User 1 has the master code or master
TAG and is the only user authorised to modify all users' CODES and TAGS. All
codes should be different from one another and from other duress codes (+1 to
existing codes).
• It is possible to simplify the arming operation by changing ARM WITH CODE
so the system arms without a code or a TAG.
• You can bypass a detector for one set period if you need to leave a room
without protection by accessing the MANUAL BYPASS menu and selecting a
detector.
• You can customize the arrow keys on your keypad for direct access to
functions in the menu by modifying SHORTCUTS.
• TIME AND DATE can be updated by the user on some systems.
EVENT MENU
You can view EVENTS recorded by the system on your keypad screen.
TEST MENU
To verify the performance of your system, you can test SIRENS and LIGHTS.
You can also initiate a search for mobile keypads out of their base by accessing
SEARCHING TCU.
If your system requires maintenance, your alarm company can request remote
access to your system: enter MAINTENANCE mode to authorize the remote
maintenance.
E
N
G
L
I
S
H
- 7 -
TESTS
1- SIRENS
2- LIGHTS
3- TRANSMISSION
4- MAINTENANCE
5- SEARCHING TCU
NO YES
1 - ANNEX
2 - SILENT MODE
3 - CHIME
4 - MAIL
5 - EVENTS
6 - SETTINGS
7 - TESTS
8 - REMOTE PLUGS
SYSTEM SETTINGS
1 - CODES
2 - TAGS
3 - MANUAL BYPASS
4 - ARM WITH CODE
5 - DATE AND TIME
6 - SHORTCUTS
7 - LANGUAGES

E
N
G
L
I
S
H
- 8 -
OTHER FUNCTIONS
You can deactivate the beeps played on the panel's built-in siren by selecting the
SILENT MODE.
You can also activate the chime, which may be associated to some of the
detectors in your installation by accessing the CHIME menu.
Home automation functions are in a dedicated menu REMOTE PLUGS. Select
the electrical device** and turn it on or off. On some systems, it is possible to
trigger the camera on detectors equipped with one.
BATTERY REPLACEMENT
The battery indicator on the keypad display indicates when to replace
the battery. Open the battery cover on the back of the keypad and insert a
CR123A 3V battery, respecting the polarities.
** This function requires an optional X10 extension with X10 modules.
WARNING
There is a risk of explosion
in case of incorrect
replacement of the battery.
Replace only with a battery
of the same type or an
equivalent type, which has
been recommended by the
manufacturer.

5- How to use the wireless keypad with prox reader*
The keypad is used to arm and disarm your security system using a valid access
code or key TAG. To use all his functions you must have the master code chosen
during the installation or have the master key TAG.
ARMING USING YOUR CODE OR TAG
Press an arming key on the keypad
Enter a valid code or present a programmed TAG**
A flashing red light on the keypad confirms that the code is valid.
The arming tone is emitted by the panel siren followed by the exit delay
beeps. If the system diagnoses a fault on arming, the arming tone is
followed by a tone indicating a fault.
Arming is automatically completed at the end of the delay (Depends
on site configuration).
Always make sure that your arming request is followed by the arming tone.
If a perimeter fault is signalled on arming, please disarm the system before
verifying doors and windows equipped with contacts.
DISARMING USING YOUR CODE OR TAG
To enable you to get to the keypad without triggering an alarm, your installer has
programmed an entry delay of 30 seconds (Depends on site configuration).
Enter a valid code or present a programmed TAG
A green light on the keypad confirms that the code is valid:
The disarming tone is emitted by the panel siren.
Disarming the system will also stop the sirens if an alarm is triggered. Stopping
the siren does not interrupt the transmission of the alarm to the ARC.
Note: Depending on your keypad's configuration, this will disarm the total set or the entire system.
In the latter case, the annex set might need to be re-armed.
* The system may include 0 to 4 keypads of this type.
** On some keypad models, presenting the TAG more than 2 seconds will arm the system without pressing the Arm key.
E
N
G
L
I
S
H
- 9 -
Total set arming
Part set arming
TAG 4- or
6-digit code
TAG 4- or
6-digit code