Honeywell NOTIFIER PAN1-PLUS User manual

Installation and user Manual
Fire alarm devices - Visual and acoustic alarm device
PAN1-PLUS
General features:
The panel PAN1-PLUS is a device conceived for acoustic and optical signaling of fires.
All materials utilized to produce it comply to fire system requirements and the housing is built with fireproof
materials.
The alarm device has to be installed by qualified personnel only, respecting all installation norms and
adequate distances and highness to get the best optical and acoustic performances.
TECHNICAL DATA
Category
W-4,5-10, Wall mounted device (DIP7 OFF)
•
Coverage volume
standard flash power 4,5x10x11 m (HxWxD)
•Max Current absorption
100mA average /140mA peak @ Vdc=24V
Category
W-4-9, Wall mounted device (DIP7 ON)
•
Coverage volume
reduced flash power 4x9x9 m (HxWxD)
•Max Current absorption
70mA average / 90mA peak @ Vdc=24V
Nominal Voltage supply
24Vdc (from 20Vdc to 30Vdc)
Max Power absorption
2.4W (DIP7 OFF), 1.7W (DIP7 ON),
Max current absorption for sound
20mA +/-5mA
Flash - Strobo frequency
0.6Hz
Main sound frequency (average)
Sound 1 983 Hz
Main sound pattern
Sound 1 Pulsed at 1.2 Hz
Max level SPL @1 m
See Diagram 1
Available Patterns
4 available patterns: 1 modulated, 1 pulsed, 1 bitonal,1
continuous
Operating temperature
From -10 °C to +55°C
Command from the control panel
Polarity inversion
Enclosure protection degree
IP21C (Type A, for indoor use)
Size (WxHxD)
307 x 117 x 55 mm
Weight
539 gr
Standards
EN54-3:2001 + A1:2002 + A2:2006,
EN54-23:2010
S-310.1-PAN1P-ENG Rev. A.1 02/2018
PAN1-PLUS
Visual and acoustic fire alarm device

Diagram 1 (Sound power distribution):
PAN1-PLUS
horizontal degrees
DIP 5OFF 6OFF 101dB
PAN1
-PLUS
vertical degrees
DIP 5OFF 6FF 101dB
DIP 3OFF 4OFF DIP 3ON 4OFF DIP 3OFF 4ON DIP 3ON 4ON DIP 3OFF 4OFF DIP 3ON 4OFF DIP 3OFF 4ON DIP 3ON 4ON
S1 S2 S3 S4 S1 S2 S3 S4
min dB(A) @1m
min dB(A) @1m
min dB(A) @1m
min dB(A) @1m
min dB(A) @1m
min dB(A) @1m
min dB(A) @1m
min dB(A) @1m
15 98 98 99 99 15 90 82 84 84
45 101 99 102 101 45 102 92 95 93
75
98
100
100
99
75
107
97
99
98
105 95 100 96 95 105 102 93 95 93
135 97 99 99 99 135 108 99 101 99
165 99 98 101 100 165 100 88 90 89
PAN1
-PLUS
horizontal
degrees
DIP 5ON 6OFF 97dB
PAN1
-PLUS
vertical degrees
DIP 5ON 6OFF 97dB
DIP 3OFF 4OFF DIP 3ON 4OFF DIP 3OFF 4ON DIP 3ON 4ON DIP 3OFF 4OFF DIP 3ON 4OFF DIP 3OFF 4ON DIP 3ON 4ON
S1 S2 S3 S4 S1 S2 S3 S4
min dB(A) @1m
min dB(A) @1m
min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m
15
92
95
95
93
15
88
97
89
89
45
97 96 99 97
45
97 96 99 98
75 94 97 96 93 75 101 100 104 101
105 91 98 93 91 105 97 98 99 97
135 94 96 96 93 135 102 100 105 103
165 95 95 97 96 165 92 95 95 93
99dBA
DOWN
UP
101dB - Sound S3
RIGHT
LEFT
100dB
Sound S2 – DIP - 5 OFF 6 OFF

Pict. 1
PAN1
-PLUS
horizon
tal
degrees
DIP 5OFF 6ON 94dB
PAN1
-PLUS
vertical degrees
DIP 5OFF 6ON 94dB
DIP 3OFF 4OFF DIP 3ON 4OFF DIP 3OFF 4ON DIP 3ON 4ON DIP 3OFF 4OFF DIP 3ON 4OFF DIP 3OFF 4ON DIP 3ON 4ON
S1
S2
S3
S4
S1
S2
S3
S4
min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m min dB(A) @1m
15 89 92 91 90 15 85 94 85 85
45
93
93
95
94
45
93
93
95
94
75 90 95 92 90 75 98 97 99 98
105 88 95 90 88 105 93 95 95 94
135 90 93 92 90 135 100 97 101 100
165 91 92 94 93 165 89 93 91 90
Installation:
Connection
Connect the main output with “polarity inversion” to positive (A+) and negative (A-) terminals (see. Pict.1)
with a certified wire. Moreover, insert the end-of-line R resistor between the “A+” terminal and the “A-”
terminal. The value of the end-of-line R resistor depends on the kind of main installed, and it is indicated in
the main installation manual.
Terminal SYNC (Synchronism): if required, connect together the terminal SYNC of the devices to
synchronize them.
Terminals B+ B- (Buzzer Mute): if required, applying 24Vcc between B+ and B- or short-circuiting B- with A-,
the buzzer is silenced.
Selection of backlight mode
DIP switch 1-2
Description
OFF -OFF (Default) Backlight blinking at 0.6 Hz
ON – OFF Backlight OFF
OFF -ON Backlight ON
ON – ON Backlight OFF
Selection of sound pattern and power
DIP switch 3-4
Description
OFF - OFF (Default) 983Hz pulsed at 1.2 Hz
ON - OFF Sweep from 1200 Hz to 500 Hz at 1.2Hz
OFF -ON 983-750 Hz alternate at 1.2Hz
ON - ON 983Hz continuous
SYNCRONISM
R
POSITIVE IN STANDBY
CONNECT THE MAIN
OUTPUT WITH POLARITY
INVERSION
NEGATIVE IN STANDBY
MUTE BUZZER
SYNCRONISM

Pict. 2
DIP switch 5-6
Sound Level at 1 m
OFF -OFF (Default)
101 dB
ON - OFF 97 dB
OFF -ON 94 dB
ON - ON Sound disabled (NOT COMPLIANT TO EN54-3)
Selection of flash power
DIP switch 7
Flash pulse power
Coverage
Current absorption
OFF (Default) Standard
4,5x10x11 m (HxWxD)
100mA
ON
Reduced
4x9x9 m (HxWxD)
70mA
Wall fixing:
Fix the device on the wall through the 4 holes on its base (see Pict. 2).
Use an adapter to connect all cables in case of a system with external tubes.
The device is classified W-4,5-10. It is designed to cover a maximum volume with a side of 10 m, front side
11 m and height of 4,5 m, see Pict. 3. The device must be placed with the long side parallel to the floor, and
the flash-lens on the bottom.
Fix the screws on the top and on the bottom of the device with a Torx screwdriver.
In case of any modification of one or more of the above topics, the certification will be not valid.
Warranty: All Notifier products have 1 year of guarantee.
4,50 m
(4,00 m)
11,00 m
(9,00 m)
10,00 m
(9,00 m)
Pict. 3
Fixing Holes
Torx
Screws
MAX COVERAGE

DoP available on web site www.notifier.it
1293
Notifier s.r.l. Via A: Grandi, 22, 20097 S. Donato Milanese (MI) Italy
18
DoP 1293 - CPR - 0597
EN54-3 EN54-23
PAN1-PLUS
FIRE ALARM DEVICES – VISUAL AND ACOUSTIC ALARM DEVICE
Intended for use in fire detection and fire alarm systems in and around buildings
TYPE A: for indoor use
Other technical data: see supplier’s technical dossier.
Essential characteristics
Performance
Performance under fire conditions
Pass
Operational reliability
Pass
Durability of operational reliability and response delay, temperature
resistance
Pass
Durability of operational reliability, humidity resistance
Pass
Durability of operational reliability, shock and vibration resistance
Pass
Durability of operational reliability, corrosion resistance
Pass
Durability of operational reliability, electrical stability
Pass
Durability of operational reliability, resistance to ingress
Pass
ATTENTION:
Please note that all installation indications here above must be carefully respected to prevent the device from
loosing its standard compliance.
Numero Assistenza Tecnica: 039-9301410
NOTIFIER ITALIA S.r.l. - A socio unico - 20097 San Donato Milanese (Ml) - Via Grandi, 22 - Tel.: [phone] - Fax: [phone] - E-mail: [e-mail]
www.notifier.it - Capitale Sociale € 2.700.000,00 i.v. - C.C.A.A. 1456164 -Trib. Milano Reg. Soc. 348608 - Vol. 8549 Fasc. 8 - Codice Fiscale 05108880153 - Partita
IVA IT 11319700156 (informativa privacy art. 3 Digs 196/03) - Uffici Regionali: 10095 Grugliasco (TO) – Via Don Caustico, 123 - Tel.: [phone] - Fax:
011/4531183 - E-mail: [e-mail] - 35010 Limena (PD) Via IV Novembre, 6/c Int. 9 - Tel.: [phone] - Fax: [phone] - E-mail:
[e-mail] - 40050 Funo di Argelato (BO) - Asta Servizi, Bl. 3B, Gall. B n. 85, Centergross - Tel.: [phone] - Fax: [phone] - E-mail:
[e-mail] - Roma - Via Del Casale Santarelli, 51 - Tel.: [phone] - Fax: [phone] - E-mail: [e-mail] - 80143 Napoli - Palazzo
Prof. Studi - Centro Direzionale, Isola E2, Scala B, Piano 5° - Tel.: [phone] - Fax: [phone]- E-mail: [e-mail] - 95126 Catania - Viale Alcide
De Gasperi, 187 - Tel.: [phone] - Fax: [phone] - E-mail: [e-mail]
www.notifier.it
Tutti i dati sono soggetti a cambiamento senza preavviso. Tutti i diritti di questa pubblicazione sono riservati.