HOOKE ROAD MMR.10060 User manual

Hard Top Removal Tool
(1) Contents:
Qty
Part Name
Size(mm)
Qty
Part Name
Size(mm)
1
Hard Top Removal Tool Assembly
I1
×
16
Hex Socket Head Cap Screws
M8*20
G
brake wheel X2
Flat Washer×2
M8
G
free wheel X2
Nylon Insert Lock nut
M8
Z1×2
casing
6.2”
I2
×
2
Hex Socket Head Cap Screws
M6*50
Z2×2
casing
16”
Flat Washer×2
M6
Z3×2
casing
19”
Nylon Insert Lock nut
M6
H1
×
4
Hex Socket Head Cap Screws
M6*40
J1
×
2
Rubber base
M6*120
Flat Washer×2
M6
Flat Washer×2
M6
Nylon Insert Lock nut
M6
thumb screw
M6
H2
×
8
Socket Head Cap Screws
M8*80
Hex Nuts
M6
Split Lock Washer×2
M8
J2
×
4
Rubber base
M8*100
Flat Washer×2
M8
Flat Washer×2
M6
Nylon Insert Lock nut
M8
Hex Nuts×2
M6
MMR.10060

J3×2
thumb screw
M8*20
K2
×
1
Hex Socket Head Cap Screws
M8*45
J4×4
Hex Socket Head Cap Screws
M8*130
Split Lock Washer×2
M8
K1
×
1
Adjustable travel stop
Flat Washer×2
M8
Hex Bolt
M6*12
Nylon Insert Lock nut
M8
Flat Washer×2
M6
K3×1
Spring
1.5*12*50
Hex Nuts
M6

NOTES:
Subject to the number of
accessories received.

(2) Tools required:
(3) Installation time:
About 3-4 hours, 3-4 people may be needed. Installation time may differ
according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (MMR.10060), please scan the QR code.
a. 10mm & 13mm & 14mm Wrench;
b. 5mm & 6mm Hex Bit Socket;

(4) Installation instruction:
The main part, please see the following steps for detailed steps.

Base Installation:
Step 1: Install the wheels (Part “G”) on the Part ”F” (number 1). Free wheels is
installed in the front, brake wheels is installed in the rear. Install the Part
“Z3” into the Part “F” (number 1).
Step 2: Install the Part “E” (number 2). Clamp the Part “K5” at the connection.

Step 3: Sleeve into round tube (Part “Z2), There are multiple holes on the top
and bottom of the tube for you to choose, and the height of the product
assembled with different holes is different.
Support Platform Installation:
Step 4: Install the Part ”D” (number 3) into the Part “Z2”. Assemble the Part “C”
(number 4) & the Part “D” (number 3).

Step 5: Install two round pipes (Part “Z1”) into the Part “D” (number 3). Next,
connect the support body (number 5) to the round tube.
Step 6: Adjust the height of the support platform to the minimum. Install the
Part “J2” & Part “K4” into the Part “A” (number 5). Notes: If your vehicle is TJ,
Replace the screws in the Part “J2” with the Part “J4”.

Step 7: Install critical brakes-Part “K7” (in screw pack4).
1Install the brake disc in the two holes above the side with the
handbrake with the Part “I2” (in screw pack2).
2Install the adjustable travel stop (Part “K1” in screw pack 4) in the
second hole on the side with the handbrake.

3First install the spring in the adjustable travel stop and ring,
remove the screw on the adjustable travel stop and insert it into the
brake rope, restore and tighten the screw to lock the brake rope.
Note: Clamp the wire rope with a pliers and string in the screw,
screw in the screw, clamp the wire rope and adjust the screw to the
proper position

Step 8:
Install the Part “J1”, Part “J3” & the Part “B” (in screw pack 3).

Instructions for use:
1. When preparing to disassemble, adjust the height of the front support
device to be higher than the rear.
2. After the roof is stuck, install the front supports（Part “F”)The front of the
first roof should be significantly higher than the rear, and the recommended
distance is about 4 inches, as shown in the figure below. At this time, the roof
has a certain height so that it will not bump the vehicle body.
High
Low
About 4 “

3. When adjusting the height up and down, please support the armrest firmly
and then adjust the height slowly. This method is the safest to use.
4. We recommend that the two support devices in front of you support the
two large boards in front of the hardtop, and the four support devices in the
back support the edge of a small board on one side. As the picture shown.

Step 9:
The installation is complete. We hope you enjoy a wonderful off-road life
with this quality Hooke Road product!
Attention:
1.The product parts in this instruction may differ slightly from the
actual product contents but generally does not affect the installation
of the product.
2.Please feel free to contact your distributor if you have any kind
of question about your purchase.
Hooke Road to find your parts