HP 64655A User manual

SERVICE BRIEF
TIEWLEIT-PACKARD
MODEL 5I+655A
8085 TNTERFACE MoDIILE
o C0PYRIGHT HEWTETT PACKARD COMPANY/IOGIC SYSTEMS DMSION 1983
1900 GARDEN Or THE GODS ROAD, COLORADO SPRINGS, COLoRADO' U.S-4.
ALL RIGHTS BESER\IED
Service Brief Part Number 5\655-90903
llicrofiche Part Number 6\65>-gO8OZ PRINIED: JANUARY L983

CERTIFICATION
Hewlett-Packard Company certifies that this product met its pubtished specifications at the
time of shipment from the factory. Hewtett-Packard further certifies that its catibration
measurements are traceable to the lJnited States National Bureau of Standards, to the extent
allowed by the Bureau's calibration facility, and to the calibration facilities of other
lnternational Standards Organization members.
WARRANTY
This Hewlett-Packard system product is warranted against defects in materials and
workmanship for a period of 90 days f rom date of installatio;. During the warranty period, Hp
will, at its options, either repair or replace products which prove to be defective.
Warranty service of this product will be performed at Buyer's facility at no charge within Hp
service travel areas. Outside HP service travel areas, warranty service will be ferformed at
Buyer's facility only upon HP's prior agreement and Buyer shall pay Hp's round trip travel
expenses. ln all other cases, products must be returned to a service facility designated by Hp.
For products returned to HP for warranty service. Buyer shall prepay shipping charges to Hp
and HP shall pay shipping charges to return the product to Buyer. However, Auyer shall pay all
shipping charges, duties, and taxes for products returned to Hp from another country.
HP warrants that its software and firmware designated by HP for use with an instrument will
execute its programming instructions when properly installed on that instrument. Hp does not
warrant that the operation of the instrument, or software, or firmware will be uninterrupted or
error free.
LIMITATION OF WARRANTY
The foregoing warranty shall not apply to defects resulting from improper or inadequate
maintenance by Buyer, Buyer-supplied software or interfacing, unauth orized modification or
m isuse, operatio n outside of the environ mental specif ications for the prod uct, or im proper site
preparation or mai ntenance.
NO OTHER WARRANTY IS EXPRESSED OR IMPLIED. HP SPECIFICALLY DISCLAIMS THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE,
EXCLUSIVE REMED!ES
THE REMEDIES PROVIDED HEREIN ARE BUYER'S SOLE AND EXCLUSIVE REMEDIES. HP
SHALL NOT BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEOUENTIAL DAMAGES, WHETHER BASED ON CONTRACT, TORT, OR ANY OTHER
LEGAL THEORY.
ASSISTANCE
Product maintenance agreements and other customer asslstance agreements are available tor
Hewlett- Packard prod ucts.
For any asslstance, contact your nearest Hewlett-PackardSales and Service Off ice.
cw&A 2/81

SAFETY SUMMARY
The tollowlng general salety precautlons must be observed during all phases ol operation, service,
and repair of this instrument. Faiture to comply with these precautions or with ipecitic'warnings
elsewhere in this manual violates salety standards ol design, manulacture, and intended use ol tie
instrument. Hewlett'Packard Company assurnes no tiability lor the cuslomerb laiture to comply
with these requirements.
GROUND THE INSTRUMENT.
To minimize shock hazard, the instrument chassis and cabinet must be connected to an electrical
ground The instrument is equipped with a three-conductor ac power cable. The power cable
must either be plugged into an approved three-contact electrical ouilet or used with a three-contact
to two-contact adapter with the grounding wire (green) firmly connected to an electrical ground
(safety ground) at the power outlet. The power jack and mating plug of the power cable meet
lnternational Electrotechnical Commission llECt safety standards.
DO NOT OPERATE tN AN EXPLOSIVE ATMOSPHERE.
Do not operate the instrument in the presence of flammable gases or fumes. Operation of any
electrtcal instrument in such an environment constitutes a definite safety hazard.
KEEP AWAY FROM LIVE CIRCUITS.
Operating personnel must not remove instrument covers. Component replacement and internal
adjustments must be made by qualified maintenance personnel. Do not replace components wrth
power cable connected. Under certain conditions, dangerous voltages may exist even with the
power cable removed. To avoid injuries, always disconnect power and discharge circuits before
touching them.
DO NOT SERVICE OR ADJUST ALONE.
Do not attempt internal service or adjustment unless another person, capable of rendering first ard
and resuscitation, is present.
DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT.
Because of the danger of introducing additional hazards, do not install substitute parts or perform
any unauthorized modtfication of the instrument Return the instrument to a Hewlett-Packard
Sales and Service Office for servrce and repair to ensure that safety features are maintained.
DANGEROUS PROCEDURE WARNINGS.
Warnings, such as the example below, precede potentially dangerous procedures throughout this
manual. lnstructions contained in the warnings must be followed.
Dangerous voltages,
Use extreme caution capable ol causing death,
when handling, testing, and are present in this instrumenl.
adjusting.
ss-1-1 /6

Service--Model 6\6SSe
Figure 1. Model 6\6SSg fnterface Module

Service_ _Model 5t+G5>e
GENERAL IMORMATIOI.
The Model 6\655e, 808! rnterface Modure, provides a dedicated interface between
a microprocessor system and either the Model LS3}A/D r,ogic Ana{yr", or the Model
5l+6zos Logic ana]ryzer. Although both hard.ware and software are needed to
provide this interface, the. software element is beyond the scope of this
manual' For information in addition to the following trief description please
refer to the Model 5h520S or the Model AG3OA/D Operating Manual.
The software portion includes format specification data and a disassembler.
The format specification data includes infozmation on which analyzer bits or
fields contain address, data and status information, which clock signals to
use and their polarities. The disassembler, a set of tables for an inverse
assembler program, a1lows the analyzer to displ-ay mnemonics in addition to
binary display.
The Module eontains circuitry required to interface the Logic Anatyzer to the
8085 microprocessor. fts location near the test point helps minimize loading
of the system under test. The Logic Analyzer mainframe supplies +5 volts to the
rnterface Module for operating power at rrt logic levers. The g0g5
rnterface Module r.D. code is !! decimar, 3T hexadecimal.
CATI]TION
Remove Poner from the System Before Preceding with the Installation
INSTATTATION IN MODET 5\65A9 CENERAT PURPOSE PREPROCESSOR
1. Connect W5 from the small General Purpose Preprocessor card (A2) to J\
on the 8085 tnterface Module.
2. Connect Wl from the large General Purpose Preprocessor card (A1) to J3
on the 8085 Interface Module.
3. Lower the Interface ModuLe into the preprocessor so
component side fits inside the pod. that the
l{. Fit the Pod Cover hinges into hinge slots on the General Purpose
Preprocessor pod. Lower the cover over the Interface Module and, fasten
down with screr{s.
cAllltr0N
To avoid possible damage from static dischargeo always connect the wire
assembly (Wl+) from the preprocessor endcap to J5 on the 8085 tnterface
Module.
a

Service--Model 6\6SSe
II{STALLATION IN MODEL LO26TA nITERFACE
1-. Connect W1 from JL on the General purpose
to J\ on the Dedicated fnterface Module.
2. Connect W2 from J3 on the General purpose
to J3 on the Dedicated fnterface Module.
Fit the Dedicated Interface Module assembly
L0269A General Furpose probe fnterface pod.
fasten dorrn with screws-
Interface Card in tine lOZ6gA
fnterface card in ttre LOZ6/A
into hinge slots on the
Lower the cover and
It may be added by installing
or L25L-3090 for a l0-pin
3.
J2 is not provided with the 8085 Interface lvtodul_e.
HP part number 1251-300)+ for a )+O-pin eonnector
connector.
IMTERFACE REQUIREMEI{TS .
The 8O8l tnterface Module
rates up to 5 lftIz. The
(excludes 808! clock pins
35 pF.
r'rilr operate with &n 808! microprocessor clocked. at
card adds one LS rrl load to a1r monitored rines
L and 2) and an interface eapacitanee of approximately
The Interface Module has user definable wirewrap
the folloring setup ancl hold specifications: pins. Inputs nust meet
Setup
Hold
5h6eoS Logic Ana1yzer
22 nS
15 nS
3"53OA/D Logic Analyzer
20 nS
0 nS min
PERFORMANCE \MRIFICATION AND ADJUSTMENT PROCEDURE
Equipment Needed (or Equivalent)
Logic probe ,.Hp LO5Z5A
Logi.c pu1ser. ".. . .Hp 1,0526T
There are no automatic performance tests and no adjustments for the ModeI
5t+6SSt.
TROUBLESHOOTING
If a failure is suspected in the HP 6l+655A rnterface Module, troubleshooting can
be done usi-ng a togic Pulser and a togic Probe. The Model 6l+5>Sg *rrut be
connected to the Model 5l+6509 or the Model 1,0269A. Remove the Z],F connector
from the system under test. Remove the 8OB5 mieroprocessor from the ZIF
connector. Pulse each pin of the ZIF socketo and, using the schematic, look for
a pulse on the appropriate pin of J3 and Jh.

Serwice- -Model 5t+655e,
Figure 2. Replaceable Parts Breakdorrn

Service--Model 6\655A
<-Mp6
<-w7
+MP4
_- MPs
Figure J. Exploded View User Plug

Service--Mode1 5L+6fie
REF HP PART C gTY
DES NI,IMBER D
Table L. Replaceable parts List
DESCRIPTION
POD COVER 808, INTERFACE CARD
U CHANNET NPRN .047-IU-WO-CHANNEI
STRAIN RELIEF BdACKET
PIN BASE-IO PrU
SOCKET-IC \OO-COrr DIP DIP-SLDR
ZIF SOCKET BOARD.bO
CABLE ASSEMBTY
BOARD ASSEMBTY-8o85
CAPACITOR-FXD . ol_UF +gO- 20% TOOVDC
CAPACTTOR-FXD . 01t F +go-20% LOOVDC
CAPACITOR-FXD . 01_UF +80- 2!ro lOO\tDC
CAPACITOR-FXD . 01UF +gO-2Aro LOOVDC
CAPACTTOR-rXD . 01UF +90- 2oro LOOVDC
CONNECTOR-POST IYPE hO DPSLDR
HEADER 6O PrN
HEADER 6O PrX
9-PrN WAFER
9 PIN POST SET
CONNECTOR IO-PIN M POST TYPE
CONNECTOR IO-PIN M POST TYPE
CONNECTOR ]-O-PII{ M POST TYPE
CoNNECTOR 25-PIN M POST TYPE
CoNNECTOR 25-PIt{ M POST TYPE
IC BFR TTL LS IINE DRVR OCTt
IC BFR TTL tS tINE DR\TR OCTt
IC BTR TTL LS LINE DRVR OCTL
IC BFR TTL tS IINE DRTR OCTL
IC BTR TTL LS LINE DRVR OCTt
IC CATE TTL S NAI{D TPT 3-INP
DIODE ARRAY hOV I+OOI A
DroDE ARRAY l+ov hooue
DIODE ARRAY lOV 4OOUE
DIODE ARRAY LOV hOOU.T
MTR MTR
CODE NT]M
MP1 5t+555-O\tot t
MPz 43eO-Oog5 T
uP3 5\65t-otzot z
MP)+ 50h-3153 5
uP5 L2O0-O682 L
MP5 5\5>r-56>o\ \
w7 8L20-36n 3
A3 5\55>-66>ot t
c1 ot6o-2055 9
e2 otSa-2o55 9
c3 ot6o-2o55 9
cU 0160-2055 9
c5 oLSo-2055 9
It tz5t.3oot+ L
J3 L25L-7575 2
J4 125L-7575 2
J5 tzSt-75t3 9
lrr1 tz5t-7597 9
wr2 tzSt-2958 T
1{r3 L25L-3958 T
wr)r L25L-3958 T
m5 n5t-\rT3 5
wt5 tz5t-t+frc 5
u1B L82a-L9LB z
u1D LBzo-1,9L8 2
t|2c LSzo-Lgtg z
u3B Lgzo-1-gLB z
u3D L820-1918 2
uLc L82o-o695 B
ucRlA t9o5-ozoz T
ucR2A t9o6-ozoz T
ucR3A t9o5-ozoz T
ucRlre tgo6-ozoz T
L
L
L
L
2
L
L
L
5
28180
28)+80
28180
28)+80
281+80
28h80
28180
28180
cER 28h80
cER 28480
cEn 28180
cER 28180
cER 281+80
28h80
281+80
e8480
28h80
281+80
281+80
28L8o
28h80
z8l+80
zBl+80
0L295
0L295
0L295
0t295
0L295
01,295
Lo295
Lo295
Lo295
Lo2g5
5\655-or*ot
\3zo-0095
6\555-otzot
5oW-:,L53
L200-0582
6t+65t-565ot+
8L2o-3623
6t+615-6550t
ot6o-2o55
otSo-2055
oLSo-2055
otSo-zor5
ot6o-2o55
L25L-3oot+
t25L-7575
L25L-7575
tzjt-76t3
L25L-T5gT
L25L-3958
L25L-3958
L25L-3918
]-zS]--t+773
L25a-\773
SNTI+LS2llil,I
SUTl+f,Se\fN
sN?)+ts2l+1N
suTl+lsebrN
sr7hlse)+ru
suThr,se\rl.I
TIDI3O
TIDI3O
TIDI3O
TIDI3O
L
2
L
L
3
2
5
L
l+
Mfr No.
olzg5
Table 2. Manufacturer's
Manufacturer Name
Texas fnstr Inc Semicond Cmpnt Div
Code
Address
. Dallas Tx
Zip Code
75222

Service- -Model 6\5SSe,
l-Wr1-l
ffi
twr4 1
-r^.1-
IIE !E
!H[l;E
E-l ["1
-cs- I I
8085 INTERFACE