Htek UC924U User manual

Solid green when power on, flashing red when there are new messages.
Dialing or during a conversation.
Ringing.
Idle interface.
Pick up the handset; enter the number, then press the send soft key or press .
Press or the line keys; enter the number, then press the send soft key or press .
Press ; enter the number, then press the send soft key or press .
Hang up the handset or press the cancel soft key.
Press , or press the cancel soft key.
Press the cancel soft key.
Pick up the handset.
Press .
Press .
Press to redial the last call you dialed.
Press or the hold soft key during a call to hold the call.
Press or the resume soft key to resume the held call.

1) Press or Transfer soft key during the conversation, the call is on hold now.
2) Enter the number you want to transfer to.
3) Press or the B Transfer soft key and now the blind transfer completed.

1) Press or Transfer soft key during the conversation, the call is on hold now.
2) Enter the number want to transfer to and press the send soft key or .
3) Start the second conversation, press or Transfer soft key, then Transfer completed.

1) Press or Transfer soft key during the conversation, the call is on hold now.
2) Enter the number want to transfer to, and then press , then you can hear the ring tone.
3) Press or the Transfer soft key and now the Semi-attended Transfer completed.
Assuming that Aand B are in Aconversation.A want to bring C (or D & E) in a conference:
1) Apresses Hold, the call is placed on hold.
2) Apresses New Call, enter the number of C and then press send soft key or , C answers the call.
3) A presses or the conference soft key, thenA, B and C are now in a conference.
4) If add D&E,A press Hold, the current conference is on hold, press New Call and dial D, D answer
the call. APress Hold and New Call and dial E, E answer the call.A press , then A, B, C, D, E
are in a conference.
Press to mute the microphone during the call.
Press again to un-mute the conversation.

1) Press Menu → Setting → Advanced Settings (Default password: admin)
2) Select Network: To configure the Wan Port (DHCP/Static/PPPoE), PC Port etc.
3) Select Accounts: Enable the account, fill in the SIP Server, Outbound Proxy and the SIP
registration information.
1) Get the IP address from the phone: Press Menu -> Status-> Information.
2) Login: Input the IP address in the web browser (Login name: admin. Default password: admin).
3) Configuration: Fill in the SIP Server info on the Profile page and the Account registration info
on the Account page.
4) Click on Save Set.
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Tel: [phone] | Fax: [phone] | Mail: [email protected] | Web: www.htek.com
Add: 5th Floor, 1st Building Huashen Tech Park10 Huashen Temple Yuhuatai Dis Nanjing 210012 China
Copyright: © Nanjing Hanlong Technology Co., Ltd. 2005-2021 All rights reserved.
IP Phone
Quick Reference for UC924U