Htek UC926U User manual

Steady green when power on, blinking green when the call is ringing.Blinking red
When there are new messages.
During the conversation, or plan to dial a call.
The call is ringing.
Idle interface.
Pick up the handset; enter the number, then press the send soft key or press .
Press or the line keys; enter the number, then press the send soft key or press .
Press , enter the number, then press the send soft key or press .
Hang up the handset or press the cancel soft key.
Press , or press the cancel soft key.
Press the cancel soft key.
Pick up the handset.
Press .
Press .
Press to redial the last call that dialed.
Press or press the hold soft key during a call to hold the call.
Press or press the resume soft key to resume the call.
1) Press or transfer soft key during the conversation, the call is on hold now.
2) Enter the number that transfers to.
3) Press or the B Transfer soft key and now the blind transfer completed.
1) Press or transfer soft key during the conversation, the call is on hold now.
2) Enter the number that transfer to and press the send soft key or .
3) Start the second conversation, press or transfer soft key, then transfer completed.
1) Press or transfer soft key during the conversation, the call is on hold now.
2) Enter the number transfer to, and then press , then you can hear the ring tone.
3) Press or the Tran soft key and now the Semi-attended transfer completed.
Assuming that Aand B are in conversation. Awants to bring C (or D & E) in a conference:
1) Apress Conference soft key, the call is placed on hold.
2) Aenter the number of C and then press send soft key or , C answers the call.
3) Apress the conference soft key, thenA, B and C are now in a conference.
4) If add D&E, Apress Hold soft key, the current conference is on hold, press New Call soft key and
dial D, D answer the call. APress Hold soft key and New Call soft key and dial E,E answer the call. A
press the conference soft key, then A,B,C,D,E are in conference.
Press to mute the microphone during the call.
Press again to un-mute the conversation.
When you want to change from the low angle position to another positions.
Please take out the hook switch then rotate it 180 degrees then slide it back into its groove.

1) Press Menu → Setting → Advanced Settings (Default password: admin)
2) Select Network: To configure the Wan Port (DHCP/Static/PPPoE), PC Port etc.
3) Select Accounts: Enable the account; fill in the SIP Server, Outbound Proxy and the SIP
Registration information.
1) Get the IP address from the phone: Press Menu→ Status→Information.
2) Login: Input the IP address in the web browser. The PC and phone should be in the same IP
address segment (Login name: admin ; Default password: admin).
3) Configuration: Fill in the SIP Server info on the Profile page and theAccount registration info on
the Account page.
4) Click on SaveSet and Restart the Phone if needed.
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
Tel: [phone] | Fax: [phone] | Mail: [email protected] | Web: www.htek.com
Add: 5th Floor, 1st Building Huashen Tech Park10 Huashen Temple Yuhuatai Dis Nanjing 210012 China
Copyright: © Nanjing Hanlong Technology Co., Ltd. 2005-2020 All rights reserved.
IP Phone
Quick Reference For UC926U