HunterDouglas RB 500 Safety guide

Standard+ Clutch with 5.875" Dual Bracket
Manual Clutch Installation
Mount into wood or metal studs or into concrete with concrete anchors.
Drywall anchors are not recommended.
Determine the mounting location.
a) surface/wall b) ceiling c) in recess/end mount
Measure and mark the bracket locations with a pencil.
Mount brackets with the screws provided. Pre-drilling is recommended.
Check that the brackets are level and aligned.
5.875” DUAL BRACKET WITH STANDARD
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
1 of 3
a
c
b
Insert the provided Allen key into the set screw
of the leveler.
Adjust skewing by turning the Allen key left or
right to move the shade up or down. Support
the shade with your hand if necessary.
All adjustments can be made after the shade
has been installed and after the operation has
been tested.
OPTIONAL: INTEGRATED LEVELER
ADJUST LEVELER
TOOLS NEEDED
INSTALLING THE BRACKETS
Pencil Level
Measuring
Tape Drill with
bits
Allen Key
(provided with
optional Leveler)
Screwdriver Pliers
Ensure the leveling set screw
opening is pointing downwards
before installing the bracket.
The orientation can be changed
by loosening the two screws
(M3x6) and turning the leveler
90°. Fix the screws after turning.
112119

LOCK THE SHADE
2 of 3
INSTALLING THE SHADE - Do not remove the tape around the shade until it is fully installed
CHECK SHADE
OPERATION
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
CLUTCH BRACKET IDLE BRACKET
UNLOCKED
CORD TENSIONER
INSTALLATION
BALL STOP
INSTALLATION
LOCKED
Remove the tape from the shade.
Make sure the shade operates properly.
Pull the front chain down to raise the shade.
Pull the back chain down to lower the shade.
Adjust leveler if applicable.
SET LOWER LIMIT
Lower shade to the bottom of the window opening.
Place a ball stop over the chain in front of the clutch
and secure using pliers.
SET UPPER LIMIT
Raise shade to the desired height.
Place a ball stop over the chain in back of the clutch
and secure using pliers.
Be sure the cord tensioner is not placed in the path of the bottom
rail and fabric.
Unlock the cord tensioner by removing the plug from the screw hole
and pushing down.
Hold the cord tensioner firmly in place and check that the bead chain,
ball stop, and chain connector can move freely through it. The chain
should not be taught.
Mark the screw hole with a pencil. Attach the cord tensioner directly
to the wall using a 1½” screw. Use a wall anchor if necessary.
Standard+ Clutch with 5.875" Dual Bracket
Manual Clutch Installation
2
1
Place the clutch onto the clutch bracket.
Push the shade against the clutch end and
lift the roller shade up until the end plug fits
into the center of the idle bracket.
Rotate the nut on the
idle end clockwise until
it meets the tube. This
locks the shade into
position.

Move the shade
downward and out
of the clutch bracket.
Rotate the nut
on the idle end
counterclockwise
to unlock the shade.
Slide a flat head
screwdriver between
the idle end plug and
bracket and push
towards the clutch
end to remove the
plug from the bracket.
2
1
3
3 of 3
SHADE REMOVAL
UNLOCK THE SHADE REMOVE IDLE END REMOVE CLUTCH END
© 2018 Hunter Douglas. All rights reserved. All trademarks used herein are the property of Hunter Douglas or their respective owners.
Las Vegas • Chicago
800.229.5300
HDhospitality.com
Standard+ Clutch with 5.875" Dual Bracket
Manual Clutch Installation