IBASE Technology SE-603-N User manual

SE-603-N
Intel® 11th Gen Core™
Outdoor Signage Player
User’s Manual
Version 1.0
(July 2023)

ii
SE-603-N User Manual
Copyright
©2023 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

SE-603-N User Manual
iii
Compliance
In a domestic environment, this product may cause radio interference in which case
users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class B
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
SE-603-N User Manual
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
•Lay the device horizontally on a stable and solid surface in case the device may
fall, causing serious damage.
•Leave plenty of space around the device and do not block the openings for
ventilation. NEVER DROP OR INSERT ANY OBJECTS OF ANY KIND INTO
THE VENTIILATION OPENINGS.
•DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY IS BELOW -20°C OR ABOVE 80°C. This
could damage the device. The device must be used in a controlled environment.
Care for IBASE products:
•Before cleaning the device, turn it off and unplug all cables such as power in case
a small amount of electrical current may still flow.
•Use neutral cleaning agents or diluted alcohol to clean the device chassis with a
cloth. Then wipe the chassis with a dry cloth.
•Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots
from being clogged.
WARNING
Attention during use:
•Do not place heavy objects on the top of the device.
•Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult the distributor or local power
company.
•Do not walk on the power cord or allow anything to rest on it.
•If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
Avoid Disassembly
Do not disassemble, repair or make any modification to the device. Doing so could
generate hazards and cause damage to the device, even bodily injury or property
damage, and will void any warranty.

SE-603-N User Manual
v
CAUTION
There is danger of explosion if internal lithium-ion battery is replaced by an incorrect
type. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices,
power adapter, panel and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from the distributor or sales representative,
prepare the following information:
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact the distributor or sales representative.

vi
SE-603-N User Manual
Table of Contents
Chapter 1 General Information .............................................................1
1.1 Introduction.............................................................................................2
1.2 Features..................................................................................................2
1.3 Packing List ............................................................................................3
1.4 Specifications..........................................................................................3
1.5 Product View...........................................................................................5
1.6 Dimensions.............................................................................................8
Chapter 2 Hardware Installation & Motherboard Information ..............9
2.1 Installation / Replacement.....................................................................10
2.2 Setting the Jumpers..............................................................................15
2.3 Jumper & Connector Locations on Motherboard...................................16
Chapter 3 Driver Installation .................................................................30
3.1 Introduction...........................................................................................31
3.2 Intel®Chipset Software Installation Utility..............................................31
3.3 VGA Driver Installation..........................................................................33
3.4 HD Audio Driver Installation..................................................................35
3.5 LAN Drivers Installation.........................................................................36
3.6 Intel® ME Drivers Installation................................................................38
3.7 Intel Thunderbolt Drivers Installation.....................................................39
Chapter 4 BIOS Setup............................................................................40
4.1 Introduction...........................................................................................41
4.2 BIOS Setup...........................................................................................41
4.3 Main Settings........................................................................................42
4.4 Advanced Settings................................................................................42
4.5 Chipset Settings....................................................................................52
4.6 Security Settings...................................................................................55
4.7 Boot Settings.........................................................................................57
4.8 Save & Exit Settings..............................................................................58
Appendix ......................................................................................................59
A. I/O Port Address Map............................................................................60
B. Interrupt Request Lines (IRQ)...............................................................62
C. Watchdog Timer....................................................................................63

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Packing List
•Accessories
•Specifications
•Product View
•Dimensions

2
SE-603-N User Manual
1.1 Introduction
Powered by 11th Gen Intel® Core™processors and supporting up to 64GB DDR4-
3200 memory, the SE-603-N delivers high performance, reliability and security, and
enables smooth 4K media playback on three independent displays.The SE-603-N
features various connectivity options such as M.2 E-Key (2230) for Wi-Fi, Bluetooth,
or capture card options and M.2 B-Key (3052) for 5G options. The fanless design
enables silent operation, making it ideal for use in noise-sensitive environments. It
can also operate in a wide-range temperatures from -20°C to 70°C, making it suitable
for use in various rugged environments.
1.2 Features
•iSMART energy-saving & Observer remote monitoring technologies
•11th Gen Intel® Core™/ Celeron® U-Series Processors
•2x DDR4-3200 SO-DIMM, dual channel, Max. 64GB
•Intel® Processor integrated graphics device
•1x HDMI 2.0 , 1x DVI-D , 1x DP (supports DP++)
•1x M.2 E-Key (2230) for Wi-Fi, Bluetooth or capture card options
•1x M.2 B-Key (3052) for 5G options
•TPM 2.0, vPro and watchdog timer
•Wide-range operating temperature: -20°C ~ 70°C
•Ruggedized, fanless and all solid state design

General Information
SE-603-N User Manual
3
1
1.3 Packing List
The product package should include the items listed below.
•SE-603-N Digital Signage Player
•Power Adaptor
•Power Cord
1.4 Specifications
Product
SE-603-N
Mainboard
MBD603
CPU
11th Gen Intel® Core™/ Celeron® U-Series
(TGL-U Platform) Processors TDP<=15W
CPU Socket
SoC Integrated
Memory
2x DDR4-3200 SO-DIMM, dual channel, Max. 64GB
Graphics
Gen12 integrated graphics (up to 96EU)
LAN
1x Intel® 226IT PCI-E Gigabit LAN controller
Memory
2x DDR4-3200 SO-DIMM, dual channel, Max. 32GB
Expansion
Slots
1x M.2 E-Key (2230)
1x M.2 B-Key (3052)
1x UIM/SIM card slot
I/O Interface
1x HDMI 2.0
1x DP (supports DP++)
1x DVI-D
3x USB 3.1 Gen 2
1x USB 2.0
1x RJ45 for 2.5 Gigabit LAN
2x Audio connectors for Line-in / Line-out
2x COM ports: 1x RS232/422/485 + 1x RS232, supports ring-in
with power @500 mA (selectable for 5V or 12V)
1x DIO (4-in/4-out)
1x Power / HDD LED
1x Power button
1x 4-pin Terminal block
1x Power switch connector

4
SE-603-N User Manual
Auto Control and
Monitoring
Watchdog Timer: 256 segments, 0, 1, 2...255 (sec/min)
Construction
Aluminum + SGCC
Power
+12V DC
Weight
1.7kg (3.75lbs)
Chassis Color
Black and white
Storage
1x M.2 M-Key (2280)
Power Supply
Optional
Mounting
Standard system bracket
Dimensions
224mm(W) x 134.6mm(D) x 46.5mm(H)
103”(W) x52.9”(D) x 18.3”(H)
Operating
Temperature
-20°C ~ 70°C (-4°F ~ 167°F)
Storage
Temperature
-20°C ~ 80°C (-4°F ~ 176°F)
Relative Humidity
10% ~ 90% (non-condensing)
Vibration
SSD: 5 grms / 5~500Hz / random operation
Certification
CE, FCC class-B, cULus, UKCA
Operating System
Win10 IoT Enterprise (64-bit) Linux Ubuntu (64-bit)
Models
SE-603-N
Fanless Signage Player with MBD603 w/ Intel® 11th Gen
Intel® Core™I7-1185GRE processor TDP<=15W, 2x 4GB
SODIMM RAM, M.2 128GB storage,and 60W power adaptor
(Operating temperature -20°C~70°C; w/o adapter)
SE-603-N5
Fanless Signage Player with MBD603 w/ Intel® 11th Gen
Intel® Core™I5-1145G7E processor TDP<=15W, 2x 4GB
SODIMM RAM, M.2 128GB storage, and 60W power adaptor
(Operating temperature -20°C~70°C; w/o adaptor)
All specifications are subject to change without prior notice.
Note: The product performance relies on the system functioning as a whole. The
level of CPU/APU/GPU processor, the interaction among the processor and
the memory and storage bandwidth, or the functionality of the digital signage
application software may affect the product performance.

General Information
SE-603-N User Manual
5
1
1.5 Product View
Front View
No.
Function
1
HDMI
2
DP (supports DP++)
3
DVI-D
4
USB 3.1 @Gen 2
5
USB 2.0
6
RJ45 for 2.5 Gigabit LAN
Front View

6
SE-603-N User Manual
Rear View
No.
Function
1
Power Switch
2
Power Button
3
Line-in / Line-out
4
DIO (4-in/4-out)
5
RS232/422/485 + RS232
6
DC-in Power
Rear View

General Information
SE-603-N User Manual
7
1

8
SE-603-N User Manual
1.6 Dimensions
Unit: mm

9
Chapter 2
Hardware Installation &
Motherboard Information
The information provided in this chapter includes:
•Installation of memory, M.2 cards and antennas
•Information and locations of connectors

10
SE-603-N User Manual
2.1 Installation / Replacement
The following pictures show how to disassemble the SE-603-N. Flip the
system to expose the bottom cover and remove the six (6) screws as shown
in the picture below. Afterwards, you will be able to access the sockets and
connectors that will be discussed in the following pages.

Hardware Configuration
SE-603-N User Manual
11
2
2.1.1 Memory
To install memory modules, locate the memory slot on the motherboard and
perform the following steps:

12
SE-603-N User Manual
1. Align the key of the memory module with that on the memory slot and
insert the module slantwise.
2. Gently push the module in an upright position until the clips of the slot
close to hold the module in place when the module touches the bottom of
the slot.
To remove the module, press the ejector tabs outwards with your fingertips to
eject the module.

Hardware Configuration
SE-603-N User Manual
13
2
2.1.2 M.2 Cards
1. Locate the M.2 slot inside the device.
Align the key of the M.2 card to the interface, and insert the card
slantwise. Fix the M.2 card with an screw.
M.2 Slots
Description
J8
M.2 B-Key [supports USB2.0 & 3.0 & PCIe]
J13
M.2 M-Key
J11
M.2 E-Key [supports USB2.0 & PCIe]

14
SE-603-N User Manual
2.1.3 WiFi /5G Antenna Installation
Thread the WiFi / 5G antenna extension cable through an antenna hole of the
front I/O cover and fasten the antenna as shown below. Then apply adhesive
to the edge of the hex nut behind the front I/O cover to prevent the extension
cable from falling if the cable becomes loose.
1. Thread and fasten the hex nut and the
washer. Then install the antenna.
2. Apply adhesive around here.
Info: The diameter of the nut is around 6.35 mm (0.25”-36UNC).