IBASE Technology SI-62S User manual

SI-62S
Digital Signage Player
User’s Manual
Version 1.2
(Oct. 2020)

ii
SI-62S User Manual
Copyright
©2020 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from misuse or
inability to use the product or the information contained herein, and for any infringements of
rights of third parties, which may result from its use.
Trademarks
All the trademarks, logos and brands mentioned herein are used for identification purposes
only and may be trademarks and/or registered trademarks of their respective owners.

SI-62S User Manual
iii
Compliance
The product described in this manual complies with all applicable European Union
(CE) directives if it has a CE marking. For systems to remain CE compliant, only CE-
compliant parts may be used. Maintaining CE compliance also requires proper cable
and cabling techniques.
This product has been tested and found to comply with the limits for a Class B
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product complies with the current RoHS directives restricting the
use of the following substances in concentrations not to exceed 0.1%
by weight (1000 ppm) except for cadmium, limited to 0.01% by weight
(100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
SI-62S User Manual
Important Safety Information
Carefully read the following safety information before using this device.0
Setting up your system:
•Put the device horizontally on a stable and solid surface.
•Do not use this product near water or any heated source.
•Leave plenty of space around the device and do not block the ventilation
openings. Never drop or insert any objects of any kind into the openings.
•Use this product in environments with ambient temperatures between 0˚C and
45˚C.
Care during use:
•Do not place heavy objects on the top of the device.
•Make sure to connect the correct voltage to the device. Failure to supply the
correct voltage could damage the unit.
•Do not walk on the power cord or allow anything to rest on it.
•If you use an extension cord, make sure the total ampere rating of all devices
plugged into the extension cord does not cord’s ampere rating.
•Do not spill water or any other liquids on your device.
•Always unplug the power cord from the wall outlet before cleaning the device.
•Only use neutral cleaning agents to clean the device.
•Vacuum dust and particles from the vents by using a computer vacuum cleaner.
Product Disassembly
Do not try to repair, disassemble, or make modifications to the device. Doing so will
void the warranty and may result in damage to the product or personal injury.
CAUTION
There is a danger of explosion if the lithium-ion battery is replaced with an incorrect
battery. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries by observing local regulations.

SI-62S User Manual
v
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices,
power adaptor, display panel and touch screen.
＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you encounter any technical problems and require assistance from your
distributor or sales representative, please prepare and send the following
information:
•Product model name
•Product serial number
•Detailed description of the problem
•Error messages in text or screenshots if any
•The arrangement of the peripherals
•Software used (such as OS and application software)
3. If repair service is required, please download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/.
Fill out the form and contact your distributor or sales representative.

vi
SI-62S User Manual
Table of Contents
Compliance....................................................................................................iii
Important Safety Information.......................................................................iv
CAUTION .......................................................................................................iv
Warranty Policy..............................................................................................v
Technical Support & Services ......................................................................v
Chapter 1 General Information................................................................1
1.1 Introduction.............................................................................................2
1.2 Features..................................................................................................2
1.3 Packing List ............................................................................................3
1.4 Specifications..........................................................................................3
1.5 Product View...........................................................................................5
1.6 Dimensions.............................................................................................6
Chapter 2 Hardware Installation & Motherboard Information ..............8
2.1 Installations.............................................................................................9
2.1.1 Memory Module Installation......................................................9
2.1.2 Mini-PCIe Card Installation.......................................................9
2.1.3 WiFi / 3G / 4G Antenna Installation.........................................10
2.1.4 Mounting Installation...............................................................11
2.1.5 Pin Assignment for Power Input Connector ............................11
2.2 Setting the Jumpers..............................................................................11
2.2.1 How to Set Jumpers ...............................................................12
Chapter 3 Driver Installation .................................................................32
3.1 Introduction...........................................................................................33
3.2 Intel®Chipset Software Installation Utility..............................................33
3.3 Intel®HD Graphics Driver Installation....................................................35
3.4 HD Audio Driver Installation..................................................................36
3.5 LAN Network Driver Installation ............................................................37
3.6 Intel®Management Engine Components Drivers Installation.................39
3.7 ASMedia USB 3.1 Drivers Installation...................................................40
3.8 Fintek 8150x Serial Port Drivers Installation..........................................41

SI-62S User Manual
vii
Chapter 4 BIOS Setup............................................................................42
4.1 Introduction...........................................................................................43
4.2 BIOS Setup...........................................................................................43
4.3 Main Settings........................................................................................44
4.4 Advanced Settings................................................................................45
4.4.1 Connectivity Configuration......................................................46
4.4.2 CPU Configuration..................................................................48
4.4.3 Trusted Computing.................................................................49
4.4.4 ACPI Settings.........................................................................50
4.4.5 LVDS (eDP/DP) Configuration................................................51
4.4.6 Fintek Super IO Configuration ................................................52
4.4.7 Fintek Super IO Hardware Monitor .........................................54
4.4.8 USB Configuration..................................................................55
4.4.9 Network Stack Configuration ..................................................56
4.4.10 CSM Configuration.................................................................57
4.4.11 NVMe Configuration ...............................................................58
4.5 Chipset Settings....................................................................................59
4.5.1 Graphics Configuration...........................................................59
4.5.2 PCH-IO Configuration.............................................................61
4.6 Security Settings...................................................................................62
4.7 Boot Settings.........................................................................................64
4.8 Save & Exit Settings..............................................................................65
Appendix ......................................................................................................66
A. I/O Port Address Map............................................................................67
B. Interrupt Request Lines (IRQ)...............................................................69
C. Watchdog Timer Configuration..............................................................70

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Packing List
•Specifications
•Optional Accessories
•Product View
•Dimensions

2
SI-62S User Manual
1.1 Introduction
The SI-62S is powered by Intel®7th / 6th Gen. desktop processors and
supports three display outputs for HDMI, DVI-D and DisplayPort as well as the
iSMART energy-saving technology that features power on/off scheduling and
power resume function. It comes with a standard system bracket and
measures 436 x 93 x 345 mm.
1.2 Features
•9th/8th Gen Intel® Core™/ Pentium® / Celeron® processors
•2x DDR4 SO-DIMM, Max. 32GB, ECC compatible
•Intel® Processor integrated graphics, supports DVI-D, HDMI,
•DisplayPort
•Dual Intel® Gigabit LAN
•6x USB3.0, 2x USB2.0, 4x COM, 4x SATA III
•1x PCI-E(x16), 2x M.2
•Watchdog timer, Digital I/O, iAMT (11.6), TPM (2.0)
•1x PCI-E(x16) or 2x PCI-E(x8) based on PCI-E x16 connectors for Matrox
/ AMD / Nvidia GPU card options

General Information
SI-62S User Manual
3
1
1.3 Packing List
If you buy a barebone SI-62S, your product package should include the items
listed below. If any of the items below is missing, contact the distributor or the
dealer from whom you have purchased the product.
Drivers and this user manual are downloadable from our website.
•SI-62S Digital Signage Player x 1
•Power Cord x 1
•2-Pin Terminal Block for Power Button x 1
•Wall Mount Kit x 1
•Screws for Wall Mount Kit (M3 x 12 mm) x 8
1.4 Specifications
Product
SI-62S
System
Mainboard
MI998AF
Operating
System
•Windows 10 Enterprise (64-bit)
•Windows 8.1 (64-bit) for Intel Skylake solution series only
•Windows 7 (64-bit)
CPU
Intel®9th / 8th Gen. Core™ desktop processor
TDP<=65W
Chipset
Intel®Q370 PCH
Memory
2x DDR4 SO-DIMM, Max. 32GB
(supports ECC by CPU SKU)
Graphics
Intel®processor HD Graphics P630
Network
1x Intel®I219LM Gigabit LAN controller
1x Intel®I211AT PCI-E Gigabit LAN (as 2nd LAN)
Storage
2x 2.5” SATA SSD slots with RAID 1
Power Supply
Internal 500W PSU
Watchdog
Watchdog Timer 256 segments, 0, 1, 2…255 sec/min
iSMART
Yes

4
SI-62S User Manual
Chassis
Aluminum and SGCC, black & white
Mounting
Standard system bracket
Dimensions
(W x H x D)
406mm(W) x 345mm(D) x 93mm(H)
17.16”(W) x 15.9”(D) x 3.66”(H)
Net Weight
8 kg (17.64 lb)
Compliance
CE, FCC class B
I/O Ports
Display
•1 x HDMI
•1 x HDMI-In for capture card option
•1 x DVI-D
•1 x Display Port
LAN
2 x GbE RJ45 LAN port
Serial
2 COM ports:
•COM1 RS-232/422/485, jumperless selectable and
configurable in BIOS
•COM2 RS-232 only
USB
•6 x USB 3.0
•2 x USB 2.0
Digital I/O
1 x GPIO 4-In / 4-Out
Audio Jack
•1 x Line-In
•1 x Line-Out
•1 x Mic-In
Power Jack
1 x DC-in power jack
Expansion
•1x M.2 (E-key, type:2230)
•1x M.2 (M-key, type:2280)
•1x PCI-E (x16) or 2x PCI-E (x8) based on PCI-E x16
connectors for Matrox / AMD / NVIDIA graphics card
Environment
Temperature
•Operating: 0°C ~ 45°C (32°F ~ 113°F)
•Storage: -20°C ~ 80°C (-4°F ~ 176°F)
Relative
Humidity
10 ~ 90% (non-condensing)
Vibration
Protection
mSATA: 5 grms, 5 ~ 500 Hz, random operation
All specifications are subject to change without prior notice.

General Information
SI-62S User Manual
5
1
1.5 Product View
Top View
Front View
No.
Name
No.
Name
1
Power Button
4
GPIO 4-In & 4-Out Port
2
LED Indicators for Power &
HDD
5
DC-In 12V Connector
3
USB 2.0 Ports
6
Reset Button

6
SI-62S User Manual
Rear View
No.
Name
No.
Name
7
AC Power Input
14
LAN Ports
8
COM1 & COM2 Ports
15
HDMI Input
9
DVI-D Port
16
2-Pin Terminal Block
(For remote power button)
10
HDMI Output
17
Expansion Slots for PCIe (x16) or
PCIe (x8)
11
DisplayPort
18
Antenna Holes
12
USB 3.0 Ports
19
Mounting Kit
13
Audio Jacks
(From top to buttom: Line-
In, Line-Out, Mic-In)
1.6 Dimensions

General Information
SI-62S User Manual
7
1
Unit: mm

8
Chapter 2
Hardware Installation &
Motherboard Information
This section contains general information about:
•Installations
•Jumper and connectors

Motherboard Information
SI-62S User Manual
9
2
2.1 Installations
Before installing any card or module into the device, remove the screws
shown in the picture below to pull out and remove the cover.
2.1.1 Memory Module Installation
To install the modules, locate the memory slot on the motherboard and
perform the following steps:
1. Press the ejector tab of the memory slot down and outwards with your
fingertips.
2. Hold the memory module and align the key of the module with that on the
memory slot.
3. Gently push the module in an upright position unitl the ejector tabs of the
memory slot close to hold the module in place when the module touches
the bottom of the slot.
To remove the module, press the ejector tabs outwards with your fintertips to
eject the module.
2.1.2 Mini-PCIe Card Installation

10
SI-62S User Manual
1. Align the mini-PCIe card’s bus connector with the mini-PCIe slot, and
insert the card slantwise.
2. Push the mini PCIe card downwards as shown in the picture, and fix it with
a screw.
2.1.3 WiFi / 3G / 4G Antenna Installation
Insert the WiFi / 3G / 4G antenna extension cable through the antenna hole of
the front I/O cover and fasten the antenna as shown below. Then apply
adhesive around the hex nut behind the front I/O cover to prevent the
extension cable from falling off if the cable becomes loose.
1. Fasten the hex nut and the washer.
Then install the antenna.
2. Apply adhesive around here.
Info: The diameter of the nut is around 6.35 mm (0.25”-36UNC).

Motherboard Information
SI-62S User Manual
11
2
2.1.4 Mounting Installation
Requirements
Before mounting the system, ensure that you have enough room for the power
adaptor and signal cable routing, and have good ventilation for the power
adaptor. The method of mounting must be able to support weight of the SI-
62S plus the weight of the suspending cables attached to the system. Use the
following methods for mounting your system:
Wall Mounting Installation
1. Turn your device upside down. Attach the wall-mount kit to the device and
secure with the supplied 8 screws.
2. Prepare at least 4 screws (M3) to install the device on the wall as shown.
2.1.5 Pin Assignment for Power Input Connector
Pin
Signal
Pin
Signal
1
Ground
2
PWR_SW
2.2 Setting the Jumpers
1 2

12
SI-62S User Manual
Configure your SI-62S by using jumpers to enable the features that you need
based on your applications. Contact your supplier if you have doubts about
the best configuration for your use.
2.2.1 How to Set Jumpers
Jumpers are short-length conductors consisting of several metal pins with a
base mounted on the circuit board. Jumper caps are placed (or removed) on
the pins to enable or disable functions or features. If a jumper has 3 pins, you
can connect Pin 1 with Pin 2 or Pin 2 with Pin 3 by shorting the jumper.
A 3-pin jumper
A jumper cap
Refer to the illustration below to set jumpers.
Pin closed
Oblique view
Illustration in the manual
Open
1-2
2-3
When two pins of a jumper are encased in a jumper cap, this jumper is
closed, i.e. turned On.
When a jumper cap is removed from two jumper pins, this jumper is open, i.e.
turned Off.
2.1 Jumper & Connector Locations
Pin# 1 23
1 2 3
1 2 3
1 2 3