IBASE Technology SI-111-N User manual

SI-111-N
Intel® Atom® x6000
Fanless Signage Player
User’s Manual
Version 1.0
(May 2023)

ii
SI-111-N User Manual
Copyright
©2023 IBASE Technology, Inc. All rights reserved.
No part of this publication may be reproduced, copied, stored in a retrieval system, translated
into any language or transmitted in any form or by any means, electronic, mechanical,
photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc.
(hereinafter referred to as “IBASE”).
Disclaimer
IBASE reserves the right to make changes and improvements to the products described in
this document without prior notice. Every effort has been made to ensure the information in
the document is correct; however, IBASE does not guarantee this document is error-free.
IBASE assumes no liability for incidental or consequential damages arising from
misapplication or inability to use the product or the information contained herein, nor for any
infringements of rights of third parties, which may result from its use.
Trademarks
All the trademarks, registrations and brands mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

SI-111-N User Manual
iii
Compliance
In a domestic environment, this product may cause radio interference in which case
users may be required to take adequate measures.
This product has been tested and found to comply with the limits for a Class B
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with manufacturer’s instructions, may cause
harmful interference to radio communications.
WEEE
This product must not be disposed of as normal household waste, in
accordance with the EU directive of for waste electrical and electronic
equipment (WEEE - 2012/19/EU). Instead, it should be disposed of by
returning it to a municipal recycling collection point. Check local
regulations for disposal of electronic products.
Green IBASE
This product is compliant with the current RoHS restrictions and
prohibits use of the following substances in concentrations exceeding
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by
weight (100 ppm).
•Lead (Pb)
•Mercury (Hg)
•Cadmium (Cd)
•Hexavalent chromium (Cr6+)
•Polybrominated biphenyls (PBB)
•Polybrominated diphenyl ether (PBDE)

iv
SI-111-N User Manual
Important Safety Information
Carefully read the precautions before using the device.
Environmental conditions:
•Lay the device horizontally on a stable and solid surface in case the device may
fall, causing serious damage.
•Leave plenty of space around the device and do not block the openings for
ventilation. NEVER DROP OR INSERT ANY OBJECTS OF ANY KIND INTO
THE VENTIILATION OPENINGS.
•Use this product in environments with ambient temperatures between 0˚C and
45˚C.
•DO NOT LEAVE THIS DEVICE IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY IS BELOW -20° C OR ABOVE 80° C. This
could damage the device. The device must be used in a controlled environment.
Care for IBASE products:
•Before cleaning the device, turn it off and unplug all cables such as power in case
a small amount of electrical current may still flow.
•Use neutral cleaning agents or diluted alcohol to clean the device chassis with a
cloth. Then wipe the chassis with a dry cloth.
•Vacuum the dust with a computer vacuum cleaner to prevent the air vent or slots
from being clogged.
WARNING
Attention during use:
•Do not place heavy objects on the top of the device.
•Operate this device from the type of power indicated on the marking label. If you
are not sure of the type of power available, consult the distributor or local power
company.
•Do not walk on the power cord or allow anything to rest on it.
•If you use an extension cord, make sure that the total ampere rating of the
product plugged into the extension cord does not exceed its limits.
Avoid Disassembly
Do not disassemble, repair or make any modification to the device. Doing so could
generate hazards and cause damage to the device, even bodily injury or property
damage, and will void any warranty.

SI-111-N User Manual
v
CAUTION
There is danger of explosion if internal lithium-ion battery is replaced by an incorrect
type. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
Warranty Policy
•IBASE standard products:
24-month (2-year) warranty from the date of shipment. If the date of shipment
cannot be ascertained, the product serial numbers can be used to determine
the approximate shipping date.
•3rd-party parts:
12-month (1-year) warranty from delivery for the 3rd-party parts that are not
manufactured by IBASE, such as CPU, CPU cooler, memory, storage devices,
power adapter, panel and touchscreen.
＊PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT,
IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE
TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED
FOR REPAIR AND SHIPPING CHARGES.
Technical Support & Services
1. Visit the IBASE website at www.ibase.com.tw to find the latest information about
the product.
2. If you need any further assistance from the distributor or sales representative,
prepare the following information:
•Product model name
•Product serial number
•Detailed description of the problem
•The error messages in text or in screenshots if there is any
•The arrangement of the peripherals
•Software in use (such as OS and application software, including the version
numbers)
3. If repair service is required, you can download the RMA form at
http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and
contact the distributor or sales representative.

vi
SI-111-N User Manual
Table of Contents
Chapter 1 General Information.......................................................... 1
1.1 Introduction .............................................................................................2
1.2 Features..................................................................................................2
1.3 Packing List ............................................................................................3
1.4 SI-111-N Specifications...........................................................................3
1.5 Product View...........................................................................................5
1.6 Dimensions .............................................................................................6
Chapter 2 Hardware Installation & Motherboard Information ..............7
2.1 Installation / Replacement.......................................................................8
2.2 Switches & Connectors on the Motherboard .........................................12
Chapter 3 Driver Installation ................................................................. 21
3.1 Introduction ...........................................................................................22
3.2 Intel®Chipset Software Installation Utility..............................................22
3.3 VGA Driver Installation..........................................................................24
3.4 HD Audio Driver Installation ..................................................................27
3.5 Intel® ME Drivers Installation ................................................................29
3.6 LAN Drivers Installation.........................................................................31
Chapter 4 BIOS Setup............................................................................ 33
4.1 Introduction ...........................................................................................34
4.2 BIOS Setup...........................................................................................34
4.3 Main Settings ........................................................................................35
4.4 Advanced Settings ................................................................................35
4.5 Chipset Settings....................................................................................42
4.6 Security Settings ...................................................................................45
4.7 Boot Settings.........................................................................................47
4.8 Save & Exit Settings..............................................................................48
Appendix ...................................................................................................... 49
A. I/O Port Address Map............................................................................50
B. Interrupt Request Lines (IRQ) ...............................................................52
C. Watchdog Timer....................................................................................53

1
Chapter 1
General Information
The information provided in this chapter includes:
•Features
•Packing List
•Specifications
•Product View
•Dimensions

2
SI-111-N User Manual
1.1 Introduction
The SI-111-N is a palm-sized fanless 4K digital signage player system based on the
Intel® Atom® x6211E and Celeron® N6210 processors. Equipped with an HDMI 2.0b
port that supports 3840 x 2160 @60Hz resolution, the industrial-grade system enables
businesses to easily connect to a 4K display and create immersive visual experiences
that attract attention and effectively promote their products or services.
IBASE values sustainable development and ESG practices. The SI-111-N
incorporates various energy-saving features, including IBASE's proprietary iSMART
green technology that enables power on/off scheduling with power resume capabilities,
and the Observer utility that remotely monitors system voltages and temperature to
ensure the system is operating efficiently while minimizing energy consumption. The
SI-111-N's extensive I/O connectivity offers a rich array of expansion options, reliable
data handling, and wireless operation, which includes 1x 2.5GbE LAN, 1x COM (RS-
232) port, 1x M.2 M-Key (2280) and 1x M.2 E-Key (2230) sockets.
1.2 Features
•Intel® Atom® X6000/ Pentium® / Celeron® Processors
•iSMART intelligent energy-saving & Observer remote monitoring
technologies
•2x DDR4-3200 SO-DIMM, Dual channel
•1x HDMI 2.0b
•3x USB 3.1
•1x 2.5GbE LAN port
•1x COM (RS-232)
•1x M.2 M-Key (2280) for storage
•1x M.2 E-Key (2230) for Wi-Fi, Bluetooth or capture card options
•TPM 2.0 and watchdog timer
•Industrial-grade robust, fanless and compact design

General Information
SI-111-N User Manual
3
1
1.3 Packing List
The product package should include the items listed below. If any of the items
below is missing, contact the distributor or the dealer from whom you
purchased the product.
•SI-111-N Digital Signage Player
•Power Adaptor
•Power Cord
1.4 SI-111-N Specifications
Product
SI-111-N
Mainboard
Mainboard
MBD111
CPU
Intel® Atom® x6211E (1.3~3.0GHz)
Intel® Celeron® N6210 (1.2~2.6GHz)
CPU Socket
FCBGA1493
Chipset
SoC Integrated
Operating
System
Win10 IoT Enterprise (64-bit)
Linux Ubuntu (64-bit)
Certification
CE, FCC class-B, UKCA, cULus, LVD
Memory
2x DDR4-3200 SO-DIMM, Max. 32GB (support IBECC)
Graphics
11th Gen Intel® SoC integrated 18EUs graphics device
LAN Controller
1x Intel® I226IT 2.5GbE LAN for Atom® x6000 series
1x Intel® I226V 2.5GbE LAN for Celeron®
Expansion Slots
1x M.2 M-Key (2280) for storage
1x M.2 E-Key (2230) for Wi-Fi, Bluetooth or capture card
options
I/O Interface
1x HDMI 2.0b 3x USB 3.1
1x RJ45 for 2.5GbE LAN
1x RJ45 for RS232 serial port
2x Audio connectors for Line-in / Line-out 1x Power button
1x Lockable power connector
1x Power / HDD LED
Watchdog Timer
256 segments, 0, 1, 2…255 (sec/ min)
Power
+12V DC
Chassis
Aluminum + SGCC
Chassis Color
Black & White
Storage
1x M.2 M-Key (2280)

4
SI-111-N User Manual
Power Supply
60W power adaptor
Mounting
Standard system bracket
Dimensions
181mm(W) x 123mm(D) x 21.5mm(H)
Certificate
CE, FCC class B, UL, CCC
Environment
Operating
Temperature
-10°C ~ 50°C (14°F~122°F) for SI-111-N
-20°C ~ 70°C (-4°F~158°F) for SI-111-N11E
Storage
Temperature
-40°C~80°C (-40°F~176°F)
Relative
Humidity
10%~90% (non-condensing)
Vibration
SSD: 5 grms / 5~500Hz / random operation
Models
SI-111-N
Signage Player with Intel® Celeron® N6210 (1.2~2.6GHz); 2x
4GB DDR4-3200 SO-DIMM, M.2 128GB storage, 1x HDMI 2.0b,
3x USB 3.1, 1x LAN, 1x COM (RJ45) and 60W power adaptor
(Operating temperature -10°C~50°C)
SI-111-N11E
Signage Player with Intel® Atom® x6211E (1.3~3.0GHz); 2x
4GB DDR4-3200 SO-DIMM, M.2 128GB storage, 1x HDMI 2.0b,
3x USB 3.1, 1x LAN, 1x COM (RJ45) and 60W power adaptor
(Operating temperature -20°C~70°C)
All specifications are subject to change without prior notice.

General Information
SI-111-N User Manual
5
1
1.5 Product View
Front View
Name
Function
SW2
Power Button
CN7
HDMI Connector
CN4, CN5, CN6
USB3.1 Connector
CN2
COM1 RS-232
CN3
LAN Connector
J7
Audio Line-In Connector
J8
Audio Line-Out Connector
Oblique View

6
SI-111-N User Manual
1.6 Dimensions
Unit: mm

7
Chapter 2
Hardware Installation &
Motherboard Information
The information provided in this chapter includes:
•Removing the brackets and system cover
•Installation of memory modules and M.2 cards
•Switches and connectors information

8
SI-111-N User Manual
2.1 Installation / Replacement
2.1.1 Removing the Brackets and Cover
The SI-111-N is provided with the two brackets installed as shown in the
picture below.
To access the internal components, turn the unit upside down and remove the
two brackets by removing the four (4) screws as shown below.

Hardware Configuration
SI-111-N User Manual
9
2
Unscrew the six (6) screws shown in the picture below to remove the bottom
cover.

10
SI-111-N User Manual
2.1.2 Installing Memory Modules and M.2 Cards
After removing the bottom cover, you are now able to access the J9 DDR4
memory slot as shown below. To install and remove a memory module, follow
the steps below.
1. Align the key of the memory module with that on the memory slot and
insert the module slantwise.
2. Gently push the module in an upright position until the clips of the slot
close to hold the module in place when the module touches the bottom of
the slot.
3. To remove the module, press the ejector tabs outwards with your
fingertips.
4. The second memory slot, J3, can be found on the other side (top) of the
board. Repeat the previous steps to install/replace a memory module.

Hardware Configuration
SI-111-N User Manual
11
2
After removing the bottom cover, you are now able to access the
J10 M.2 E-Key Connector and J11 M.2 M-Key Connector as shown below.
1. To install a card, locate the M.2 card slot. Align the key of the M.2 card to
the M.2 interface, and insert the card slantwise.
2. Push the M.2 card down, and fix it onto the standoff with a screw.

12
SI-111-N User Manual
2.2 Switches & Connectors on the Motherboard
MBD111 –top and I/O
MBD111 –back and I/O

Hardware Configuration
SI-111-N User Manual
13
2
Switches on SI-111-N
2.2.1 SW1-1: Clear CMOS Data
Function
Setting
Normal (default)
P1-OFF
Clear CMOS
P1-ON
2.2.2 SW1-2: Clear ME Register
Function
Setting
Normal (default)
P2-OFF
Clear ME
P2-ON
Switch
Function
SW1-1
Clear CMOS Data
SW1-2
Clear ME Register
SW2
Power Button

14
SI-111-N User Manual
2.2.3 SW2: Power Button
Connectors on SI-111-N
Connectors
Function
CN1
DC 12V Power Input Connector
CN2
COM1 RS232
CN3
LAN Connector
CN4, CN5, CN6
USB 3.1 Connectors
CN7
HDMI Connector
J1
SPI Flash Connector (Factory use only)
J2
Program iSmart MCU Connector (Factory use only)
J3
DDR4 Slot
J4
Program VCore Connector (Factory use only)
J5
Port 80 Connector (Factory use only)
J6
Front Panel Connector (optional)
J7
Audio Line-In Connector
J8
Audio Line-Out Connector
J9
DDR4 Slot
J10
M.2 E-Key Connector
J11
M.2 M-Key Connector