iDataLink maestro Rr User manual

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in
are the properties of their respective owners.
WARNING
Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced
options in the Print menu.
Install your Maestro RR according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE
1
2
3
SELECT VEHICLE
PRINT PAGES NEEDED

ELECTRONICS
Click here for:
Radar Installation Guides
2015-2017
Chrysler 200
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
OR
OPTIONAL ACCESSORIES
ACC-SP1
PRODUCTS REQUIRED
iDatalink Maestro RR Radio Replacement Interface
iDatalink Maestro K200 Dash Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-CHR03M-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide

ADS-RR(SR)-K200-DS-IG-EN maestro.idatalink.com
Chrysler 200 2015-2017
Automotive Data Solutions Inc. © 2019 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 5
Radio Wire Reference Chart 6
Troubleshooting Table 7
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
[email protected]

ADS-RR(SR)-K200-DS-IG-EN maestro.idatalink.com
Chrysler 200 2015-2017
Automotive Data Solutions Inc. © 2019 3
Fig. 2.5
Fig. 2.3
Fig. 2.1
Fig. 1.3 Fig. 1.4
Fig. 1.2
Fig. 1.1
Fig. 2.6
Fig. 2.4
Fig. 2.2
Fig. 2.5
Fig. 2.3
Fig. 2.1
Fig. 1.3 Fig. 1.4
Fig. 1.2
Fig. 1.1
Fig. 2.6
Fig. 2.4
Fig. 2.2
INSTALLATION INSTRUCTIONS
DASH DISASSEMBLY
Remove the radio bezel by prying it forward with a panel
removal tool. (Fig. 1.1)
Remove the (4) screws holding the radio in, then unplug
and remove the radio. (Fig. 1.2)
Remove the screw securing the bracket. Cut the plastic
at the top and bottom of the radio cavity, where indicated.
(Fig. 1.3)
Using a Dremel with a cutting wheel, cut the flat bracket
holding the front bracket as close as possible to the cross-
member. (Fig. 1.4)
DASH KIT ASSEMBLY
1. The dash kit comes with a blank panel in place of the
hazard switch. If your factory bezel has a hazard switch in
this location, remove it from the factory bezel and install it
in the K200. (Fig. 2.1)
2. Screw the (2) metal brackets into the plastic surround of
the dash kit using the supplied screws. (Fig. 2.2)
3. Clip the assembled bracket to the back side of the K200.
(Fig. 2.3)
4. Place the K200 assembly over the aftermarket radio. Adjust
the bezel and radio placement to the desired mounting
depth, and then insert the screws to fasten the metal
brackets to the radio. (Fig. 2.4)
5. Now that the radio has been secured properly to the new
brackets, unclip the radio and mounting brackets from the
K200 bezel. (Fig. 2.5)
6. Transfer the vents from the OEM radio bezel to the K200.
(Fig. 2.6)
1

ADS-RR(SR)-K200-DS-IG-EN maestro.idatalink.com
Chrysler 200 2015-2017
Automotive Data Solutions Inc. © 2019 4
INSTALLATION INSTRUCTIONS
1
MAKE CONNECTIONS (refer to wiring diagram)
1. Locate the aftermarket radio’s main harness. Connect the
wires from the aftermarket radio’s main harness to the
K200 T-harness and match the wire functions.
2. Determine if the vehicle has a factory amplifier. Look for
badges on the radio, door panels and dash that indicate the
presence of an amplifier (ex: Alpine).
If the vehicle DOES NOT have a factory amplifier:
• Plug the female GREEN connector to the male GREEN
connector of your K200 T-harness.
• Plug the female WHITE connector to the male WHITE
connector of your K200 T-harness.
If the vehicle DOES have a factory amplifier:
• Plug the female GREEN connector to the male WHITE
connector of your K200 T-harness.
• Plug the female WHITE connector to the male GREEN
connector of your K200 T-harness.
3. Connect the factory harness to the K200 T-harness.
4. Plug the aftermarket radio harnesses into the aftermarket
radio.
• Plug the Data cable to the data port of the aftermarket
radio.
• Insert the Audio cable into the iDatalink 3.5 mm audio jack
of the aftermarket radio (If there is no iDatalink audio input,
connect to AUX).
Note: On Pioneer radio, ensure that there is nothing plugged
into the W/R port.
If the vehicle is equipped with parking sensors AND using an
Alpine radio: plug Audio cable in auxiliary input of the radio.
5. Connect all the harnesses to the Maestro RR module.
• If the vehicle is equipped with OEM parking assist, lane
departure, or other safety systems, the ACC-SP1 is
required: Plug the ACC-SP1 the Maestro RR.
If you are not using this speaker, the radio will mute when
the parking assist is active. If you are using this speaker,
the parking assist chimes will play through the external
speaker and the radio will not mute unless the settings are
changed in the radio.
6. Screw the radio into the dash, clip the K200 bezel into the
dash, and test your installation.

ADS-RR(SR)-K200-DS-IG-EN maestro.idatalink.com
Chrysler 200 2015-2017
Automotive Data Solutions Inc. © 2019 5
1
BACKUP CAMBACKUP CAM
STEP 6
K200 DASH KIT
WIRING DIAGRAM
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
MAESTRO RR MODULE
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
GREEN WHITE
WHITE GREEN
CONNECTIONS WITH AMP
CONNECTIONS WITHOUT AMP
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
BLUE/WHITE - AMP. TURN ON (+)
MAIN
HARNESS
DATA
CABLE
AUDIO
CABLE
PURPLE - RR SPEAKER (+)
CONNECT TO
AFTERMARKET RADIO
K200 T-HARNESS
FACTORY RADIO
HARNESS WIRES FROM
VEHICLE
PINK - VEHICLE SPEED
YELLOW/BLACK - FOOT BRAKE
GREEN GREEN
WHITEWHITE
WHITEWHITE
BLACKBLACK
RCA CABLES
SPEAKER*
*Optional accessory
for vehicles without oem amp,
with oem parking sensors,
cross-traffic alerts or
lane departure alerts.
BROWN (NOT CONNECTED) READ NOTE IN
INSTALLATION
INSTRUCTIONS
SECTION
N.C.
PIONEER RADIO: ENSURE
THAT NOTHING IS PLUGGED
IN W/R PORT.
CONNECTION NOT REQUIRED
STEERING WHEEL
CONTROL CABLE
SEE RADIO
WIRE REFERENCE
CHART FOR
RADIO WIRE
COLORS

ADS-RR(SR)-K200-DS-IG-EN maestro.idatalink.com
Chrysler 200 2015-2017
Automotive Data Solutions Inc. © 2019 6
RADIO WIRE REFERENCE CHART
Wire
Description Polarity Wire Color on Maestro
T-Harness
Wire Color on Alpine
cable
Wire Color on Kenwood
cable
Wire Color on Pioneer
cable
Wire Color on Sony
cable
Illumination (+) Orange N/A Orange/White Orange/White Orange
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green
Foot Brake (+) Yellow/Black Yellow/Black N⁄A N⁄A N/A
VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-K200-DS-IG-EN maestro.idatalink.com
Chrysler 200 2015-2017
Automotive Data Solutions Inc. © 2019 7
TROUBLESHOOTING TABLE
PROBLEM SOLUTION
Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure the 2-pin connectors of the K200 T-harness are configured correctly,
as shown in step 2.
Reset the RR.
When making a phone call you cannot hear the callers but they can hear you. If the vehicle has a factory amplifier, make sure that the 4-pin black and
white connectors in the harness are plugged in correctly as stated in step 2.
The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module.
The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and
that it is plugged into the black port on the Maestro RR. The red and blue
ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during
the flash. Verify the radio’s serial number entered during the flash matches
what is listed on the radio screen. This can be found in the settings of the
radio, listed as Device Id, Device Number, or Serial Number.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: [phone]
Email: maestr[email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.