iDataLink maestro Rr User manual

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in
are the properties of their respective owners.
WARNING
Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced
options in the Print menu.
Install your Maestro RR according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE
1
2
3
SELECT VEHICLE
PRINT PAGES NEEDED

ELECTRONICS
Click here for:
Radar Installation Guides
2009-2012
Ford F150
with NAV
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro KFOR01 Dash Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OR
OPTIONAL ACCESSORIES

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford F150 with NAV 2009-2012
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 5
Radio Wire Reference Chart 6
Troubleshooting Table 7
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
[email protected]

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford F150 with NAV 2009-2012
Automotive Data Solutions Inc. © 2020 3
Fig. 1.3
Fig. 1.5
Fig. 1.7
Fig. 1.9
Fig. 1.1 Fig. 1.2
Fig. 1.4
Fig. 1.6
Fig. 1.8
Fig. 1.10
DASH DISASSEMBLY
1. Remove (2) 7mm screws, located under the rubber mat at
the top of the radio bezel. (Fig. 1.1)
2. At the bottom of the bezel, pry out the Aux/USB port, then
remove (1) 7mm screw. (Fig. 1.2)
3. Using a pry tool, pop out the left side panel. Unclip and
remove. (Fig. 1.3)
4. Unclip the glove box (Fig. 1.4)
5. Remove (3) 10 mm bolts securing the air bag. (Fig. 1.5) This
should expose (1) 7mm bolt securing the panel to the right
of the radio bezel. Remove the 7mm bolt, then unclip and
remove the panel. (Fig. 1.6)
6. Using a panel tool, unclip the radio bezel, then unplug and
remove it. (Fig. 1.7)
7. Remove (8) 7mm screws securing the screen and radio
chassis, then unclip and remove them. Remove the
mounting brackets from the screen and radio chassis. (Fig.
1.8)
8. Using (4) 7mm screws, reinstall the radio chassis brackets
and set the screen brackets aside to be used later. (Fig. 1.9)
9. Some trimming may be required in order for the top of the
aftermarket radio chassis to clear and sit straight in the
dash. (Fig. 1.10)
INSTALLATION INSTRUCTIONS
1

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford F150 with NAV 2009-2012
Automotive Data Solutions Inc. © 2020 4
Fig. 2.0
A B C
INSTALLATION INSTRUCTIONS
DASH KIT ASSEMBLY
1. Attach the brackets supplied with the KIT-FOR01 to the
aftermarket radio.
2. Attach mounting brackets from the OEM screen to the
FOR01 brackets. (Fig. 2.0)
3. Clip FOR01 panel on to the front of the brackets.
(Side view)
A: KFOR01 bracket
B: OEM radio bracket
C: Aftermarket radio
MAKE CONNECTIONS (refer to wiring diagram)
1. Locate the aftermarket radio’s main harness. Cut the
WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the
wires from the aftermarket radio’s main harness to the
FOR01 T-harness and match the wire functions (refer to
diagram).
2. Connect the FOR01 T-harness to the factory radio harness.
3. Plug the OBDII connector into the OBDII of the vehicle.
4. Plug the aftermarket radio harnesses into the aftermarket
radio.
Plug the data cable to the data port of the aftermarket
radio.
Insert the audio cable into the iDatalink 3.5mm audio jack
of the aftermarket radio (labeled iDatalink. If there is no
iDatalink audio input, connect to AUX).
Plug the SUB IN, Center IN and backup camera RCA into
the aftermarket radio (if applicable).
Note: When using a Pioneer radio, please ensure that there
is nothing plugged into the W/R port of the radio.
5. Connect all harnesses to the Maestro RR module.
6. Insert the radio and FOR01 kit in the dash, secure with (4)
7mm screws, then test your installation.
1

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford F150 with NAV 2009-2012
Automotive Data Solutions Inc. © 2020 5
7
BACKUP CAMBACKUP CAM
SUB IN
CENTER IN
SUB IN
CENTER IN
STEP 1 STEP 4
STEP 5
STEP 2
STEP 3
PINK/RED (NC)
STEP 6
MAESTRO RR MODULE
CUT AND REMOVE
THE RCA JACKS
MAIN
HARNESS
FO1 T-HARNESS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
BROWN (NC)
WIRING DIAGRAM
WIRES FROM
VEHICLE
FACTORY RADIO HARNESS
OBDII CONNECTOR
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
DATA
CABLE
AUDIO
CABLE
CONNECT TO
AFTERMARKET RADIO
STEP 1 STEP 4
STEP 5
STEP 2
STEP 3
NOT REQUIRED
STEERING WHEEL
CONTROL CABLE
PIONEER RADIO:
ENSURE THAT NOTHING
IS PLUGGED IN W/R PORT.

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford F150 with NAV 2009-2012
Automotive Data Solutions Inc. © 2020 6
RADIO WIRE REFERENCE CHART
Wire
Description Polarity Wire Color on Maestro
T-Harness
Wire Color on Alpine
cable
Wire Color on Kenwood
cable
Wire Color on Pioneer
cable
Wire Color on Sony
cable
Illumination (+) Orange N/A Orange/White Orange/White Orange
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green
VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford F150 with NAV 2009-2012
Automotive Data Solutions Inc. © 2020 7
TROUBLESHOOTING TABLE
PROBLEM SOLUTION
Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the
vehicle.
If you hardwired connections at the OBDII, check connections at the OBDII
connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/
BROWN wire is connected to PIN 14 of the OBDII connector. Do not use
T-Taps. Soldering or military splicing methods are recommended.
Reset the RR.
There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the
RR and the radio. Make sure it is in the correct radio input.
The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module.
The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and
that it is plugged into the black port on the Maestro RR. The red and blue
ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during
the flash. Verify the radio’s serial number entered during the flash matches
what is listed on the radio screen. This can be found in the settings of the
radio, listed as Device Id, Device Number, or Serial Number.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: [phone]
Email: maestr[email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.

ELECTRONICS
Click here for:
Radar Installation Guides
2010-2012
Ford Flex
with NAV
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro KFOR01 Dash Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OR
OPTIONAL ACCESSORIES

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford Flex with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 5
Radio Wire Reference Chart 6
Troubleshooting Table 7
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
[email protected]

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford Flex with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 3
Fig. 1.7
Fig. 1.3
Fig. 1.5
Fig. 1.4
Fig. 1.6
Fig. 1.1 Fig. 1.2
DASH DISASSEMBLY
1. Unclip and remove the trim around the shifter. Unclip and
remove the top of the center console and cupholders. (Fig.
1.1)
2. Unclip and remove the trim panel that runs along the dash
above the radio. (Fig. 1.2)
3. Remove (2) 7mm screws from the top of the radio bezel.
(Fig. 1.3)
4. Unclip the side panels on the center console. This will
expose (1) 7mm screw on each side securing the bottom of
the radio bezel. Remove these screws. (Fig. 1.4)
5. Remove (2) 7mm screws at the bottom of the radio bezel.
Unclip and remove the radio bezel. If equipped, unclip the
thermistor attached to the radio bezel and move it to the
side. (Fig. 1.5)
6. Remove (8) 7mm screws securing the screen and radio
chassis, then unclip and remove them. Remove the
mounting brackets from the screen and radio chassis. (Fig.
1.6)
7. Using (4) 7mm screws, reinstall the radio chassis brackets
and set the screen brackets aside to be used later. (Fig. 1.7)
INSTALLATION INSTRUCTIONS
1

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford Flex with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 4
Fig. 2.0
A B C
INSTALLATION INSTRUCTIONS
DASH KIT ASSEMBLY
1. Attach the brackets supplied with the KIT-FOR01 to the
aftermarket radio.
2. Attach mounting brackets from the OEM screen to the
FOR01 brackets. (Fig. 2.0)
3. Clip FOR01 panel on to the front of the brackets.
(Side view)
A: KFOR01 bracket
B: OEM radio bracket
C: Aftermarket radio
MAKE CONNECTIONS (refer to wiring diagram)
1. Locate the aftermarket radio’s main harness. Cut the
WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the
wires from the aftermarket radio’s main harness to the
FOR01 T-harness and match the wire functions (refer to
diagram).
2. Connect the FOR01 T-harness to the factory radio harness.
3. Plug the OBDII connector into the OBDII of the vehicle.
4. Plug the aftermarket radio harnesses into the aftermarket
radio.
Plug the data cable to the data port of the aftermarket
radio.
Insert the audio cable into the iDatalink 3.5mm audio jack
of the aftermarket radio (labeled iDatalink. If there is no
iDatalink audio input, connect to AUX).
Plug the SUB IN, Center IN and backup camera RCA into
the aftermarket radio (if applicable).
Note: When using a Pioneer radio, please ensure that there
is nothing plugged into the W/R port of the radio.
5. Connect all harnesses to the Maestro RR module.
6. Insert the radio and FOR01 kit in the dash, secure with (4)
7mm screws, then test your installation.
1

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford Flex with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 5
7
BACKUP CAMBACKUP CAM
SUB IN
CENTER IN
SUB IN
CENTER IN
STEP 1 STEP 4
STEP 5
STEP 2
STEP 3
PINK/RED (NC)
STEP 6
MAESTRO RR MODULE
CUT AND REMOVE
THE RCA JACKS
MAIN
HARNESS
FO1 T-HARNESS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
BROWN (NC)
WIRING DIAGRAM
WIRES FROM
VEHICLE
FACTORY RADIO HARNESS
OBDII CONNECTOR
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
DATA
CABLE
AUDIO
CABLE
CONNECT TO
AFTERMARKET RADIO
STEP 1 STEP 4
STEP 5
STEP 2
STEP 3
NOT REQUIRED
STEERING WHEEL
CONTROL CABLE
PIONEER RADIO:
ENSURE THAT NOTHING
IS PLUGGED IN W/R PORT.

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford Flex with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 6
RADIO WIRE REFERENCE CHART
Wire
Description Polarity Wire Color on Maestro
T-Harness
Wire Color on Alpine
cable
Wire Color on Kenwood
cable
Wire Color on Pioneer
cable
Wire Color on Sony
cable
Illumination (+) Orange N/A Orange/White Orange/White Orange
Reverse Light (+) Purple/White Orange/White Purple/White Purple/White Purple/White
E-Brake (-) Lt Green Yellow/Blue Lt Green Lt Green Lt Green
VSS (vehicle speed sensor) (DATA) Pink Green/White Pink Pink N/A

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford Flex with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 7
TROUBLESHOOTING TABLE
PROBLEM SOLUTION
Gauges do not work, radio shows OBD2 Error 1 or Error 2. Ensure OBDII connector is securely attached to the OBDII connector of the
vehicle.
If you hardwired connections at the OBDII, check connections at the OBDII
connector. Make sure the RED/ BROWN wire is on PIN 6 and the YELLOW/
BROWN wire is connected to PIN 14 of the OBDII connector. Do not use
T-Taps. Soldering or military splicing methods are recommended.
Reset the RR.
There is no sound from Sync (if equipped). Ensure the all black, 3-pin to 3.5mm audio cable is connected between the
RR and the radio. Make sure it is in the correct radio input.
The light on the Maestro is flashing RED ONCE. There is no firmware on the module; flash the RR module.
The light on the Maestro is blinking RED TWICE. Ensure the 4-pin data cable is connected between the radio and the RR, and
that it is plugged into the black port on the Maestro RR. The red and blue
ports on the RR should be empty.
Make sure the correct radio model and serial number were entered during
the flash. Verify the radio’s serial number entered during the flash matches
what is listed on the radio screen. This can be found in the settings of the
radio, listed as Device Id, Device Number, or Serial Number.
MAESTRO RR RESET PROCEDURE:
Turn the key to the OFF position, then disconnect all connectors from the module.
Press and hold the module’s programming button and connect all the connectors back to the module. Wait, the module’s LED will flash RED rapidly (this may
take up to 10 seconds).
Release the programming button. Wait, the LED will turn solid GREEN for 2 seconds to show the reset was successful.
TECHNICAL ASSISTANCE
Phone: [phone]
Email: maestr[email protected]
Web: maestro.idatalink.com/support add www.12voltdata.com/forum/
IMPORTANT: To ensure proper operation, the aftermarket radio needs to have the latest firmware from the manufacturer. Please visit the radio
manufacturer’s website and look for any updates pertaining to your radio.

ELECTRONICS
Click here for:
Radar Installation Guides
2010-2012
Ford FusioN
with NAV
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, FACTORY AMPLIFIER, AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro KFOR01 Dash Kit
PROGRAMMED FIRMWARE
ADS-RR(SR)-FOR01-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
OR
OPTIONAL ACCESSORIES

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford FusioN with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 5
Radio Wire Reference Chart 6
Troubleshooting Table 7
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
[email protected]

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford FusioN with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 3
CENTER
CONSOLE
DRIVER
DOOR
Fig. 1.3 Fig. 1.4
Fig. 1.1 Fig. 1.2
Fig. 1.5
Fig. 1.7 Fig. 1.8
Fig. 1.6
1
23
(a)
DASH DISASSEMBLY
1. Remove (2) 7mm screws from the pocket on top of the
dash. Remove the panel. (Fig. 1.1)
2. Note: In some trims, there is a safety strap fixed behind
the panel (Fig. 1.1 (a)) that prevents the removal of the top
plate/pocket/vents. It's not necessary to remove this unless
you want to take the pocket/vents out for ease of install.
(OPTIONAL) To completely remove the vents: looking from
the floorboard up into the dash (driver side) locate and
remove (1) 10mm bolt securing top pocket with a strap. (fig.
1.2)
Otherwise, use a panel tool to loosen the vents enough to
gain access to the top of the radio bezel.
3. Remove (2) 7mm screws securing the top of the radio
bezel. (fig. 1.3)
4. Using a panel tool, pry upward to release and remove the
plastic trim around the shifter. Unclip and remove the top
of the center console (fig. 1.4)
5. Using a panel tool, pry outward to release the radio bezel
from the dash, then unplug and remove it. (fig. 1.5)
6. Remove (8) 7mm screws securing the screen and radio
chassis, then unclip and remove them. Remove the
mounting brackets from the screen and radio chassis. (fig.
1.6)
7. Using (4) 7mm screws, reinstall the radio chassis brackets
and set the screen brackets aside to be used later. (fig. 1.7)
8. Note: In some trims, this module may have to be relocated
to make the new radio fit. (fig. 1.8)
INSTALLATION INSTRUCTIONS
1

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford FusioN with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 4
Fig. 2.0
A B C
INSTALLATION INSTRUCTIONS
DASH KIT ASSEMBLY
1. Attach the brackets supplied with the KIT-FOR01 to the
aftermarket radio.
2. Attach mounting brackets from the OEM screen to the
FOR01 brackets. (Fig. 2.0)
3. Clip FOR01 panel on to the front of the brackets.
(Side view)
A: KFOR01 bracket
B: OEM radio bracket
C: Aftermarket radio
MAKE CONNECTIONS (refer to wiring diagram)
1. Locate the aftermarket radio’s main harness. Cut the
WHITE, GRAY, GREEN and PURPLE RCA tips. Connect the
wires from the aftermarket radio’s main harness to the
FOR01 T-harness and match the wire functions (refer to
diagram).
2. Connect the FOR01 T-harness to the factory radio harness.
3. Plug the OBDII connector into the OBDII of the vehicle.
4. Plug the aftermarket radio harnesses into the aftermarket
radio.
Plug the data cable to the data port of the aftermarket
radio.
Insert the audio cable into the iDatalink 3.5mm audio jack
of the aftermarket radio (labeled iDatalink. If there is no
iDatalink audio input, connect to AUX).
Plug the SUB IN, Center IN and backup camera RCA into
the aftermarket radio (if applicable).
Note: When using a Pioneer radio, please ensure that there
is nothing plugged into the W/R port of the radio.
5. Connect all harnesses to the Maestro RR module.
6. Insert the radio and FOR01 kit in the dash, secure with (4)
7mm screws, then test your installation.
1

ADS-RR(SR)-KFOR01-DS-IG-EN maestro.idatalink.com
Ford FusioN with NAV 2010-2012
Automotive Data Solutions Inc. © 2020 5
7
BACKUP CAMBACKUP CAM
SUB IN
CENTER IN
SUB IN
CENTER IN
STEP 1 STEP 4
STEP 5
STEP 2
STEP 3
PINK/RED (NC)
STEP 6
MAESTRO RR MODULE
CUT AND REMOVE
THE RCA JACKS
MAIN
HARNESS
FO1 T-HARNESS
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+)
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
BROWN (NC)
WIRING DIAGRAM
WIRES FROM
VEHICLE
FACTORY RADIO HARNESS
OBDII CONNECTOR
SEE RADIO WIRE
REFERENCE
CHART
FOR RADIO WIRE
COLORS
DATA
CABLE
AUDIO
CABLE
CONNECT TO
AFTERMARKET RADIO
STEP 1 STEP 4
STEP 5
STEP 2
STEP 3
NOT REQUIRED
STEERING WHEEL
CONTROL CABLE
PIONEER RADIO:
ENSURE THAT NOTHING
IS PLUGGED IN W/R PORT.