iDataLink maestro Rr User manual

NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in
are the properties of their respective owners.
WARNING
Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll
down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced
options in the Print menu.
Install your Maestro RR according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE
1
2
3
SELECT VEHICLE
PRINT PAGES NEEDED

PRODUCTS REQUIRED
iDatalink Maestro RR or RR2 Radio Replacement Interface
iDatalink Maestro HRR-MA2 Installation Harness
PROGRAMMED FIRMWARE
ADS-RR(SR)-MA1-DS
ADDITIONAL RESOURCES
Maestro RR2 Programmable Outputs Guide
ELECTRONICS
Click here for:
Radar Installation Guides
20142017
MAZDA 3
TOUCHSCREEN
INSTALL GUIDE
RETAINS STEERING WHEEL CONTROLS, VEHICLE SETTINGS, AND MORE!
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here
in are the properties of their respective owners.
OR
ANTENNA ADAPTER (MAY BE REQUIRED)
HEAD UNIT ADAPTER:
ACC-HU-PIO1, SON1, KEN1, KEN2, ALP1
OPTIONAL ACCESSORIES

ADS-RR(SR)-MA2H-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2023 2
MAZDA 3 TOUCHSCREEN 20142017
WELCOME
NEED HELP?
Congratulations on the purchase
of your iDatalink Maestro RR Radio
replacement solution. You are
now a few simple steps away from
enjoying your new car radio with
enhanced features.
Before starting your installation,
please ensure that your iDatalink
Maestro module is programmed
with the correct firmware for your
vehicle and that you carefully review
the install guide.
Please note that Maestro RR will
only retain functionalities that
were originally available in the
vehicle.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Radio Wire Reference Chart 5
Module Diagnostics 6
Troubleshooting Table 7
1 866 427-2999
maestro.idatalink.com/support
www.12voltdata.com/forum
[email protected]

ADS-RR(SR)-MA2H-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2023 3
MAZDA 3 TOUCHSCREEN 20142017
STEP 1
• Disconnect the negative battery terminal (not doing so
may blow the 7.5A audio fuse 2 under hood during the
installation of the radio).
• Remove the factory radio
If using head unit adapter (sold separately), connect HRR-
MA2 harness to adapter and skip to step 2.
• Unbox the aftermarket radio and locate its main harness.
• Cut and remove the black 20 pin connector from the HRR-
MA2 T-harness and connect the wires, shown in the wiring
diagram, from aftermarket radio main harness to the HRR-
MA2 T-harness and match the wire functions.
Note: only connect purple/white wire to radio reverse input
or module damage will occur.
STEP 2
If the vehicle DOES NOT have a factory amplifier:
• Plug in the extension harness to HRR-MA2 main harness
8-pin black connector.
If the vehicle DOES have a factory amplifier:
• Plug in the extension harness to 8-pin black connector of
RCA cable.
• Connect the RCAs to the radio outputs: white/left front,
gray/right front, green/left rear, purple/right rear.
• Route the extension harness to the radio tuner in the
passenger kick panel.
STEP 3
• Connect both the 18-pin and 28-pin connectors of HRR-
MA2 T-harness to the factory radio harness (at CMU,
behind/below display).
STEP 4
• Connect the 24-pin adapter (red connector) to the factory
radio tuner in the passenger kick panel.
• Connect the adapter’s 8-pin black connector to the
extension harness.
• Plug the blue POWER ANT terminal to amplified antenna
adapter (if required).
STEP 5
• Plug the harnesses into the aftermarket radio.
• Connect the backup cam cable into the aftermarket radio
(if equipped).
• Plug the antenna adapter (if required).
• Plug the Data cable to the data port of the aftermarket
radio.
Note: On Pioneer radio, ensure that there is nothing plugged
into the W/R port.
STEP 6
• Connect all the harnesses to the Maestro RR module.
• Reconnect the negative battery terminal then test your
installation.
INSTALLATION INSTRUCTIONS P1 /1
1

ADS-RR(SR)-MA2H-DS-IG-EN maestro.idatalink.comAutomotive Data Solutions Inc. © 2023 4
MAZDA 3 TOUCHSCREEN 20142017
1
BACKUP CAMBACKUP CAM
AMP TURN ONAMP TURN ON
POWER ANTPOWER ANT
AUDIO
CABLE
*
NC
MICMIC
N.C. AMP TURN ONAMP TURN ON
POWER ANTPOWER ANT
3
4
4
3
10
18
18
18
28
20
8
8
8
8
8
20
8
24
8
MAESTRO RR MODULE
STEP 1
MAIN
HARNESS
HRR-MA2 T-HARNESS
STEP 5
STEP 6
WHITE - LF SPEAKER (+)
WHITE/BLACK - LF SPEAKER (-)
GRAY - RF SPEAKER (+)
GRAY/BLACK - RF SPEAKER (-)
GREEN - LR SPEAKER (+)
GREEN/BLACK - LR SPEAKER (-)
PURPLE/BLACK - RR SPEAKER (-)
YELLOW - 12V (+)
BLACK - GROUND
RED - ACCESSORY (+)
BLUE/WHITE - AMP. TURN ON (+)
PURPLE - RR SPEAKER (+)
ORANGE - ILLUMINATION (+)
PURPLE/WHITE - REVERSE LIGHT (+) *
LTGREEN - E-BRAKE (-)
PINK - VEHICLE SPEED
WIRING DIAGRAM
STEP 2
CMU
TUNER
STEP 3
STEP 4
SEE RADIO WIRE
CHART
FOR RADIO WIRE
COLORS
DATA
CABLE
CONNECT TO
AFTERMARKET RADIO
NOT REQUIRED
STEERING WHEEL
CONTROL CABLE
PIONEER RADIO: ENSURE
THAT NOTHING IS PLUGGED
IN W/R PORT.
* ONLY CONNECT TO RADIO REVERSE INPUT
OR MODULE DAMAGE WILL OCCUR
TO ANTENNA
ADAPTER IF REQUIRED
WITH OEM AMP
WITHOUT OEM AMP
OR
HEAD UNIT ADAPTER
SOLD SEPARATELY
IF WIRES ARE PRESENT ON
ADAPTER: SEE RADIO
REFERENCE CHART
IF NOT USING A MAESTRO HEAD UNIT ADAPTER:
CUT AND DISCARD CONNECTOR
LF OUT
RF OUT
LR OUT
RR OUT
CONNECT IF EQUIPPED *
PASSENGER KICK PANEL
BEHIND/BELOW RADIO DISPLAY