Impulse IT8001 User manual

IT8001 Chest Press
Assembly Instructions

Table of contents
Important Safety Instructions--------------------------------- 1
Exploded View Diagram------------------------------------------ 2
Hardware List--------------------------------------------------
Parts List-----------------------------------------------------
Assembly instructions------------------------------------------
------ 3
---------- 4
-- 5

Important Safety Instructions
Before beginning any fitness program, you should obtain a complete
physical examination from your physician. When using exercise equip-
ment, basic precautions should always be taken, including the following:
* Read all instructions before using the .
arewrittentoensureyoursafetyandtoprotect
* Do not allow children on or near the equipment.
* Use the equipment only for its intended purpose as described in this
guide. Do not use accessory attachments that are not recommended
by the manufacturer: such attachments might cause injuries.
* Wear proper exercise clothing and shoes for your workout---no loose
clothing.
* Be careful when getting on or off the equipment.
* Do not overexert yourself or work to exhaustion.
* If you feel any pain or abnormal symptoms, stop your workout imme-
diately and consult your physician.
* Never operate the unit when it has been dropped or damaged.
* Never drop or insert anything into any opening in the equipment.
* Always check the unit and its cables before each use. Make sure that
all fasteners and cables are secure and in good working condition.
* Frayed or worn cables can be dangerous and may cause injury.
Periodically check these cables for any indication of wear.
* Keep hands, limbs, loose clothing and long hair well out of the way of
moving parts.
* Do not attempt to lift more weight than you can control safely.
* Do not use the equipment outdoors.
* Read each step in the assembly instructions and follow the steps in
sequence. Do not skip ahead. If you skip ahead, you may learn later
that you have to disassemble compontents and that you may have
damaged the equipment.
* Assemble and operate the equipment on a solid, level surface. Locate
the unit a few feet from walls or furniture to provide easy access.
The is designed for your enjoyment. By
precautions and using common sense, you will have
pleasurable hours of healthfull exercise with the
Chest Press These instructions
the unit.
Chest Press following these
many safe and
equipment.
Personal Safety During Assembly
1

2
I Chest PressT8001
Exploded View Diagram

3
Hardware List
0 100
10 20 30 40 50 60 70 80 90 110 120 130 140 150
Inches
0123456
/
12
/
14 /
34 / 34 / 34 / 34 / 34 / 34
/
14 / 14 / 14 / 14 / 14
/
12 / 12 / 12 / 12 / 12
Millimeters

4
Hardware List
0 100
10 20 30 40 50 60 70 80 90 110 120 130 140 150
Inches
0123456
/
12
/
14 /
34 / 34 / 34 / 34 / 34 / 34
/
14 / 14 / 14 / 14 / 14
/
12 / 12 / 12 / 12 / 12
Millimeters

Parts List
Item No. Description QTY Item No. Description QTY
5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
1
1
1
1
1
1
1
1
1
2
1
3
3
2
2
1
1
5
1
1
1
1
1
2
1
1
2
9
2
1
18
2
1
5
8
6
15
4
4
14
2
3
2
2
2
1
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
1
6
2
1
4
2
2
6
4
2
5
2
6
2
8
7
40
1
2
8
27
8
10
4
17
2
2
7
4
2
2
2
2
1set
1
2
1
1
1
1
1
1
1
1
1
2
Main Upright
Main Support
Left Press Arm
Right Press Arm
Assistant Frame1
Foot Plate Support
Seat Pad Support
Back Pad Support
Assistant Frame2
Swivel Pulley Block
Moving Pulley Block
Big Washer
Washer
Wide Pulley
Small Wheel
Big Wheel
Collar
Small Collar
Pedal
Seat Pad
Back Pad
Front Decal Plate
Rear Decal Plate
Guide Rod
Weight Pin
Weight Shroud
"D" End Cap
4.5" Pulley
Side Cover
Foot Sleeve
Plastic Block
Weight Rubber Bumper
Top Plate
10lbsWeight
15lbs Weight
20lbs Weight
Button
Plastic Washer
Bolt Cover
Pulley Cover
Rubber Cap
Adj. Foot Plate
Gimbal
End Cap 25
Handle Grip
Weight Cable
Φ
Chest Press Cable
Bearing
Pop Pin
Small Shaft
Bronze Bushing ID12
Bronze Bushing Id25
Allen Bolt M12×40
Allen Bolt M10×115
Allen Bolt M10×75
Screw M6×20
Allen Bolt M10×50
Allen Bolt M10×45
Allen Bolt M10×25
Allen Bolt M10×15
Allen Bolt M8×60
Shoulder BoltM10×50
Chamfer Bolt M5×10
End CapRT40×80
Washer 38× 11×2.5
Washer 13× 24×1.5
Washer 11× 20×2
Washer 9× 16×1.5
Spring Washer
NylonLockM12
NylonLockM10
Split Pin
Sleeve RT50×100/40×80
Plug
.4
25×50×2
Plug 50
Plug 60
Spacer
Pad
ScrewST4.2 19
Decal Weight Numbers
Upper Support
"L" Plate
Decal Pinch Points
Decal Tighten
Decal Note
Allen Wrench S=6
Allen Wrench S=8
Grease
Decal Warning
Decal Maintenance Routine
Plastic Cap
Screw M6×15
ΦΦ
ΦΦ
ΦΦ
ΦΦ
Φ
□
□

Assembly instructions
Assembly of the takes professional installers about
2 hours. If this is the first time you have assembled this type of
equipment, plan to spend more time. It is strongly recom men
ded to assemble the equipment by professional installers.
You may find it quicker, safer, easier to assemble this equipment
with the help of a friend, as some of components may be large,
heavy or awkward to handle alone. It is important that you asse-
mble your product in a clean, clear, uncluttered area. This will
enable you to move around the product while you are fitting com-
onents and reduce the possibility of injury during assembly.
As with any assembled part, proper alignment and adjustment
is critical. While tightening the fasteners, be sure to leave room
for adjustments. Do not fully tighten the fasteners until instructed
to do so. Be careful to assemble the components in the sequence
presented in this guide.
Chest Press
-
p
Note
6

Step1 Install The Adj.Foot Plates
7
Align the Adj.Foot Plates (#42) to the Main Upright(#1)
and the Main Support(#2) then secure them by hands.

Step2 Assemble The Frame
8
1)Secure the Upper Support (#81) to the Main Support
(#2), using
2)Attach the Main Support (#2) and the Upper Support
(#81) to the Main Upright(#1) using
11× 20×2
two Allen Bolts(#54) M10×115
four Washers(#67) 11× 20×2
two Locknuts(#71) M10
four Allen Bolts(#54) M10×115
eight Washers(#67)
four Locknuts(#71) M10
ΦΦ
ΦΦ

Step3 Assemble The Foot Plate
9
1)Attach the Foot Plate Support(#6) to the Main Support
(#2) using
2)Attach the Pedal (#19) to the Support (#6)using
two Allen Bolts(#55) M10×75
four Washers(#67) 11× 20×2
two Locknuts(#71) M10
eight Allen Bolts(#61) M8×60
eight Washers(#68) 9× 16×1.5
ΦΦ
ΦΦ

10
Step4 Assemble The Assistant
Frame1
Attach the Assistant Frame1(#5) to the Main Support
(#2) using
ΦΦ
one Allen Bolts(#59) M10×25
one Spring Washers(#69) 9× 16×1.5
one Small Collar(#18)
one Collar(#17)
one Big Washer(#12)

11
Step5 Assemble The Assistant
Frame2
Align the Assistant Frame2(#9) to the Main Support(#2)
and secure it into place using
ΦΦ
Φ
two Allen Bolts(#60) M10×15
two Washers(#65) 38× 11×2.5
two Spring Washers(#69) 10
one Small Shaft(#50)

Step6 Assemble The Left
Press Arm
12
Attach the Left Press Arm(#3) to the Main Support(#2)
sing
one Allen Bolt(#59) M10×25
two Small Collars(#18)
one Spring Washer(#69) 10
one Big Washer(#12)
Φ

13
Step7 Assemble The Right
Press Arm
This assembly is the same as step 6.

14
Step8 Assemble The Weight Plates
1)Insert the two Guide Rods(#24) into the Main Upright
(#1).
2)Slide the Weight Rubber Bumper(#32) down onto each
Guide Rod(#24).
3)Carefully begin sliding the Weight Plates one by one
in sequence:#36,#35,#34,#33
4)Align both top ends of the Guide Rods(#24) to the Main
Upright(#1) and secure them using
two Allen Bolts(55) M10×75
two Washers(#67) 11× 20×2
two Spring Washers(#69) 10
two Rubber Caps(#41)
ΦΦ
Φ
Note
Make sure that Washers(#67)and Spring Washers
(#69) are on the top side.

Step9 Route The Weight Cable
1)Put the Clip tied on the weight pin leash onto the Top
Plate (#33) as shown below,next connect the Weight
Cable(#46) to the Top Plate(#33).
2)Route the Weight Cable (#46) up and over the two Pu-
lleies (#28), next, secure them to the Main Upright
(#1) using
3)Route the Weight Cable(#46) down and under the two
Pulleies (#24) next, secure them to the Main Upright
(#1) and the Main Support(#2) using
4)Connect the looped end of the Weight Cable (#46) to
the Moving Pulley Block(#11).
two Allen Bolts(#58) M10×45
four Washers(#67) 11× 20×2
two Nylon Locknuts(#71) M10
two Shoulder Bolt(#62) M10×50
two Nylon Locknut(#71) M10
four Pulley Covers(#40)
ΦΦ
15

Clip
Top plate
Step 9
16

Step10 Route The Chest
Press Cable
1)Connect the end of Chest Press Cable (#47)to the Gi-
mbal (#43), next secure the Gimbal (#43) to the Main
Support(#2) using:
2)Route the Chest Press Cable(#4 ) over the Wide Pul-
ley(#14),and insert the Spacer(#77) and the "L" Plate
(#82) onto the Wide Pulley(#14),then secure them to
the Right Press Arm(#4) by tightening the Wide Pulley
(#14).
3)Route the Chest Press Cable (#4 ) under the Pulley
(#28),and secure the Pulley (#28) to the Swivel Pull
Block(#10) using:
4)Route the Chest Press Cable(#4 ) up and over Pulley
(#28), and secure them to the Upper Support (#81)
using
5)Route the Chest Press #4 ) down and under the
Pulley (#28),and secure them to the Moving Pulley Bl
ock (#11) using
6)Route the Chest Press Cable(#4 ) up and over Pulley
(#28), and secure them to the Upper Support (#81)
using
7)Route the Chest Press Cable (#4 ) down and under the
Pulley (#28),and secure them to another Swivel Pul
Block(#10) using
one Allen Bolt (#53) M12×40
two Washers (#66) 13× 24×1.5
one Nylon Locknut(#70) M12
one Shoulder Bolt(#62) M10×50
two Pulley Covers(#40)
one Nylon Locknut(#71) M10
one Shoulder Bolt(#62) M10×50
two Pulley Covers(#40)
one Nylon Locknut(#71) M10
one Shoulder Bolt(#62) M10×50
two Pulley Covers(#40)
one Nylon Locknut(#71) M10
one Shoulder Bolt(#62) M10×50
two Pulley Covers(#40)
one Nylon Locknut(#71) M10
one Shoulder Bolt(#62) M10×50
two Pulley Covers(#40)
one Nylon Locknut(#71) M10
ΦΦ
7
7
ey
7
Cable( 7
-
7
7
ley
17

8)Route the Chest Press Cable(#47) over the Wide Pul-
ey(#14),and insert the Spacer (#77) and the "L" Plate
(#82) onto the Wide Pulley (#14),then secure them to
the Right Press Arm(#4) by tightening the Wide Pulley
(#14).
9)Connect the looped end of the Chest Press Cable(#47)
to the Gimbal (#43), then secure the Gimbal (#43) to
the Main Support(#2) using
10)Adjust the tension of the Weight Cable (#46) using
the Jam Nut
11)Make sure that the cables are in the grooves of all
the pulleies then fully tighten all bolts and nuts.
12)Select an approprate weight by the Weight Pin.
one Allen Bolt(#53) M12×40
two Washers(#66) 13× 24×1.5
one Nylon Locknut(#70) M12
ΦΦ
Step10 Route The Chest
Press Cable
18