Insportline 5547 Sprynkl User manual

USER MANUAL - EN
IN 5547 Magnetic Treadmill inSPORTline Sprynkl

IMPORTANT !
Please read all instructions carefully before using this product.
Retain this manual for future reference.
IMPORTANT SA ETY IN ORMATION
WARNING: TO REDUCE THE RISK OF SERIOUS INJURY, READ THE FOLLOWING IMPORTANT PRECAUTIONS
BEFORE USING THE TREADMILL.
1. Before tarting to exerci e, read the manual carefully and al o alway keep thi manual with you.
2. Before beginning any exerci e program you hould con ult your doctor fir t to determine if you have
any medical or phy ical condition that could put your health and afety at ri k or prevent any damage.
Your doctor’ advice i e ential if you are taking medicine that affect your heart rate, blood pre ure
or chole terol level.
3. Be aware of your body’ ignal . Incorrect or exce ive exerci e can damage your health. If you feel
dizzine , nau ea, che t pain, back pain or other health ymptom top the workout at once and con ult
your doctor before continuing.
4. Do not operate any exerci e equipment if it i not a embled well. Al o you mu t in pect your machine
periodically to en ure your machine in good condition. If there are any defective component , do not
u e the treadmill. It i your re pon ibility to en ure that all u er of the equipment are informed of all
warning and precaution .
5. Keep children and pet away from the equipment. The equipment i de igned for adult u e only. The
equipment i not uitable for therapeutic u e.
6. Before u ing the machine, plea e check the nut and bolt are ecurely tightened.
7. Alway u e the equipment a mentioned. If any defective component while a embling or checking
the equipment ha been found, or you hear any unu ual noi e from the equipment during u e, top
immediately. Do not u e the equipment until the problem ha been rectified.
8. Wear appropriate workout clothing while exerci ing. Do not wear robe or other clothing that could
become caught in the machine. Running or aerobic hoe are al o required while u ing the machine.
9. U e the equipment on a flat level, clear urface. Do not u e the machine near the water or outdoor .
10. Keep hand away from all moving part . While lifting or moving the equipment, alway do it carefully.
11. The equipment ha been te ted and certified to En957 under cla H.C. for home u e only. Maximum
weight of u er: 100kg/220Lb .
12. The minimum backward clearance required i 1200mm, the other three ide i 300mm.

EXPLODE-VIEW

PART LIST O EXPLODE-VIEW
NO. PART Q’TY
A Bolt M8X50 4
B Wa her ID8.2*OD16.2 4
C Arc Wa her ID8.2*ID22.2 2
D Screw M6X10 2
E Wa her φ 6.2 2
F Bolt M8X50 2
G Big Wa her ID8.2*ID22.2 2
H Bolt M8X45 2
I Screw M4*15 2
J Knob M8*60 1
K Screw M5*10 2
L Nut M8 4
M Wrench S13 1
N Wrench S6 1
O Wrench S5 1
1 Main Frame 1
2 Rear Roller 1
3 Pla tic Wa her 4
4 Steel end 2
5 Bolt M6X75 2
6R Rear End Cap(R) 1
6L Rear End Cap(L) 1
7 Screw M4*15 2
8 Rear Axle 1
9 Rear u pen ion 2

10 Side Rail 2
11 Nut M8 2
12 Pla tic End Cap 4
13 Bolt M8x45 1
14 Handle pul e wire 1 et
15 Pla tic End Cap 4
16 Screw M6*25 1
17 Nut M6 1
18 Ba e of The Magnet 1
19 Nut M8 2
20 Bolt M8x40 2
21 Pla tic Wheel 2
22 Ba e frame cu hion 2
23 Bottom Frame 1
24 Right Side Handle Po t 1
25 Ten ion 1
26 Screw M5X15 1
27R-R&L Cover Of Handle 2
28L- L&R Cover Of Handle 2
29 Handle Bar 1
30 Computer 1
31 Sen or Wire Connector 1 et
32 Screw M5*25 10
33 Left Side Handle Po t 1
34 Spring 1
35 Wooden Deck 1
36 Running Belt 1
37 End Cap 2
38 Pla tic Cover 1

39 Front Axle 1
40 Front Roller 1
41 Screw M3 2
42 Sen or Control 1
43 Handle Bar Grip 2
44 Handle Bar Grip 2
45 Hand pul e connector 2
46 Screw M4*20 2
47 Wa her φ 5.2 2

ASSEMBLY IN ORMATION
NO. PART Q’TY NO. PART Q’TY
1 Main frame 1 29 Handle Bar 1
23 Bottom frame 1 30 Computer 1
24 Right ide handle po t 1 33 Left ide handle po t 1
27R-R&L Cover of handle 2 38 Pla tic Cover 1

28L-L&R Cover of handle 2
ASSEMBLY
30 MIN
NOTICE
• Read thi manual before a embly.
• Recognize the pare part fir t.
• Check the hardware.
• En ure that you have the right tool.
• Prepare an area to a emble.
• Follow the in truction accordingly.
• Never force the joint
• Periodically tighten the joint .

PART LIST O ASSEMBLY

ASSEMBLY
1. STEP:

2. STEP:

3. STEP:
Before you a emble the ten ion cable, plea e make ure that it i at the level 8.
THE ASSEMBLY OF MAGNETIC TENSION ADJUSTING SET IS AS THE FOLLOWING STEPS:
A. In ert C through A. (Note: G through under the Main Frame)

B. Pull G downward in order to make A be near B,
C. Revolve D a the drawing direction in order to tighten the e two part well.

4. STEP:

5. STEP:

6. STEP:

7. STEP:

8. STEP:

You’d better check if all the part are well fa tened or not before u ing.

STORAGE
Plea e loo en knob (NO. J) completely before folding the treadmill. Then lift the Main frame （NO.1） to the
upright po ition and u e knob (J) to fa ten it tightly to prevent any accident in advance.
TREADBELT ADJUSTING
If the following ituation i happened on the tread belt, it will make ome noi e on the machine. So if the tread
belt i not in the center po ition, too tight or too loo e, plea e u e the tool to adju t it .
1. When the tread belt move to the right ide, plea e revolve the right ide hexagon ocket crew clockwi e 1
or 2 circle , revolve back a little bit.
2. When the tread belt move to the left ide, plea e revolve the left ide hexagon ocket crew clockwi e 1 or
2 circle , revolve back a little bit.
3. When the tread belt i too tight, plea e revolve the left and the right ide hexagon ocket crew
anticlockwi e, then revolve back a little bit.
4. When the tread belt i too loo e, plea e revolve the left and the right ide hexagon ocket crew clockwi e,
then revolve back a little bit.