Insportline IN 5563 User manual

USER MANUAL - EN
IN 5563 Magnetic Treadmill inSPORTline Jorney

ONTENT
IMPORTANT SAFETY INSTRUCTIONS ............................................................................................................ 3
OVERVIEW DRAWING ....................................................................................................................................... 4
PARTS LIST ........................................................................................................................................................... 5
TOOL ...................................................................................................................................................................... 7
ASSEMBLY INSTRUCTIONS .............................................................................................................................. 8
OPERATING THE COMPUTER ......................................................................................................................... 12
STORAGE ............................................................................................................................................................ 13
ADJUSTMENTS .................................................................................................................................................. 14
LUBRICATION.................................................................................................................................................... 15
MAINTENANCE ................................................................................................................................................. 1
TROUBLESHOOTING ........................................................................................................................................ 1
WARM UP AND COOL DOWN ROUTINE ...................................................................................................... 1

IMPORTANT: Read all instructions carefully before using this product. Retain this owner’s anual for
future reference.
The specifications of this product ay vary fro this photo, subject to change without notice.
IMPORTANT SAFETY INSTRU TIONS
Basic precautions should always be followed, including the following safety instructions when using this
magnetic treadmill: Read all instructions before using this magnetic treadmill.
1. Check every part of the equipment before exercise. If there is any defective component, replace it
immediately; keep the equipment out of use until repair.
2. Make sure all parts, bolts and nuts are well assembled and locked before exercise.
3. Never insert any object into any opening.
4. Never operate this magnetic treadmill if it is not working properly. If it has been dropped or damaged, or
been exposed to water, return the appliance to a service center for examination and repair.
5. Do not attempt any maintenance or adjustments other than those described in this manual. Should any
problems arise, discontinue use and consult your local dealer.
. Wear comfortable and suitable clothing when using the magnetic treadmill. Do not use the magnetic
treadmill barefoot, in only socks or in sandals, always wear athletic shoes. Never wear loose clothing
because it could run the risk of getting caught in the magnetic treadmill.
7. Keep children and pets away from the equipment while in use.
8. Do not use the magnetic treadmill outdoors. This magnetic treadmill is for household use only.
9. Only one person should be on the magnetic treadmill while in use.
10. Keep the magnetic treadmill on a solid, level surface with the minimum safety area clearance of 2000mm x
1000mm of the magnetic treadmill. Be sure the area around the magnetic treadmill remains clear during
use and has adequate clearance.
11. Hold the handlebar with your hands when starting or stopping exercise and increasing or decreasing the
speed.
12. If feeling chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately and
consult your physician before continuing.
13. The maximum weight capacity for this product is 110kgs.
WARNING: Before beginning any exercise program consult your physician. This is especially important
for the persons who are over 35 years old or who have pre-existing health problems. Read all instructions
before using any fitness equipment.
AUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.

OVERVIEW DRAWING
39
37
36
34
19
51
51
52
54
56
51
49
4
60
60 28
29
28
29
58
43
57
53
43
40
25
17
25
1
29
28
29 28
28 29
28 29
51
51
15
20
21
21
20
21
20
21
20
33
33
32
11 10
12
13
14
50
50
51
22
44
27 26
35
29
32
18 19
22 7
39
29
48
55 29 48
46
45
52
3
56
54
53
29 55
55 29
53
47
20
9
47
20
59
16
22
8
6
23
24
22
42 41
35
31
5
31
38
32
34
36
37 29
39
2
30
26 27
46
45
39 29 48
4
45
46
55
29
48
49
46
45
34

PARTS LIST
No. Description Qty
001 Main Frame 1
002 Handlebar Support Frame 1
003 Incline Adjuster 1
004
Handlebar Support Frame Base
Tube
2
005 Handlebar Ø28x1.5t 1
00 Front Roller 1
007 Rear Roller 1
008 Front Roller Axle Ø12x512 1
009 Rear Roller Axle Ø12x480 1
010 Magnet Bracket 1
011 Magnet 30x15x8 8
012 Nut M 1
013 Spring Ø23xØ1. x110 1
014
Tension Control Knob Bracket
74x25x31
1
015 Bolt M5x10 2
01 Running Deck 444x10 5x12 1
017 Running Belt 2450x400x1.2 1
018 Left Side Rail 10 5x20x1.5 1
019 Bolt M x40
020 Washer Ø xØ12x1.0 8
021 Nylon Nut M
022 C Ring Ø12
023 Protective Cover 1
024 Screw ST4.2x10 2
025 Bolt Cap S1 2

02 Hexagon Head Bolt M10x 0 2
027 Big Washer Ø10xØ20 2
028 Bolt M8x15 12
029 Washer Ø8xØ1 x1.5t 20
030 Locking Knob M8x 5 1
031 Handlebar Knob M8x45 2
032 Wire Grommet Ø12.1 3
033
Hand Pulse Sensor with Wire
1200mm
2
034 Screw ST4.2x20 4
035 Handlebar End Cap Ø32 2
03
Handlebar Foam Grip
Ø31xØ37x430
2
037 Cap Nut M8 2
038 Computer (HR1752) 1
039 Bolt M8x50 4
040 Tension Control Knob 1
041 Big Washer Ø5xØ20 1
042 Bolt M5x20 1
043 Sensor with Wire I (L=1400mm) 1
044 Screw ST2.9x12 2
045 Bumper Ø39xH17 4
04
Pan Head Phillips Self Drilling
Screw ST4.8x20
4
047
Hexagon Socket Head Cap Bolt
M x50mm
2
048 Sleeve Ø8.2xØ12.5x .5 4
049 Transport Wheel Ø51xØ9xH22 2
050 Anti-slip Pad 2

051 End Cap 40x20x1.5
052 Locking Pin Ø8x38 2
053 End Cap 0x30x1.5 3
054 Bolt M8x40 2
055 Nylon Nut M8 4
05 Incline Adjuster End Cap Ø38x1.5 2
057 Washer Ø5xØ12x1.0 2
058 Extension Sensor Wire (L=750mm) 1
059 Right Side Rail 990x20x1.5 1
0 0 Square End Cap (38x38x1.5) 2
SILI ONE OIL IN LUDED
TOOL
Allen Wrench 6mm
1PC
Multi Hex Tool with Phillips Screwdriver S10,
S13, S1 , S15 1PC

ASSEMBLY INSTRU TIONS
Step 1
Place the magnetic treadmill in the upright position.
Remove twelve M8x15 Bolts (28) and twelve Ø8xØ1 x1.5t Washers (29) from both Handlebar Support Frame
Base Tubes (4). Remove bolts with the mm Allen Wrench provided.
Install both Handlebar Support Frame Base Tubes (4) to the Handlebar Support Frame (2) by inserting both
Handlebar Support Frame Base Tubes (4) into the Handlebar Support Frame (2), using twelve M8x15 Bolts (28)
and twelve Ø8xØ1 x1.5t Washers (29) that were removed. Tighten bolts with the mm Allen Wrench provided.
NOTE: It is recommended that you always use the aid of a second person when assembling the treadmill.
2
4
4
28
29
28 29
29
28
29
28
28
29
28 29
Tool:
Allen Wrench 6mm

2
1
30
Step 2
Place one hand on the rear end of Main Frame (1) and use the other hand to remove the Locking Knob (30) by
turning it in a counterclockwise direction from the Handlebar Support Frame (2). Then Lower the Main Frame
(1) down onto the floor and align Locking Knob hole. Tighten the Locking Knob (30) by turning it in a
clockwise direction into the holes on the left side of the Handlebar Support Frame (2) and Main Frame (1).
TO PREVENT INJURY PLEASE MAKE SURE YOU HAVE A FIRM HOLD WHEN
SETTING DOWN THE DE K.
AUTION: Failure to secure the Main Frame with the Locking Knob may
cause the treadmill unstable and cause bodily injury.

2
531
31
Step 3
Remove two Handlebar Knobs (31) from the Handlebar Support Frame (2) and Handlebar (5). Then pull the
Handlebar (5) all the way up. Install two Handlebar Knobs (31) onto the Handlebar (5) by turning them in a
clockwise direction into the holes on the Handlebar (5) to secure the Handlebar (5) in place.

Step 4
Remove two ST4.2x20 Screws (34) from the back of the Computer (38). Remove screws with the Multi Hex
Tool with Phillips Screwdriver provided.
Remove the battery cover that is located on the back of the Computer (38).
Connect the Hand Pulse Sensor Wires (33) and Extension Sensor Wire (58) to the wires that come from the
Computer (38). Tuck wires into the Computer (38). Be careful not to pinch the wires.
Align the Computer (38) into the holes in the Handlebar (5) and replace the battery cover onto the back of the
Computer (38). Finally, using two removed ST4.2x20 Screws (34) to secure the Computer (38) in place.
Tighten screws with the Multi Hex Tool with Phillips Screwdriver provided.
5
58
33
38
34
Tool:
Multi Hex Tool with Phillips Screwdriver S10,
S13, S14, S1

OPERATING THE OMPUTER
SPE IFI ATIONS:
TIME --------------------------------------------------- 0:00-99:59 MIN: SEC
SPEED ------------------------------------------------ 0.0-99.9 KM/H
DIST (DISTANCE) ---------------------------------- 0.00-99.99 KM
CAL (CALORIES) ----------------------------------- 0.0-999.9 KCAL
ODO (ODOMETER) -------------------------------- 0.0-999.9 KM
PULSE ------------------------------------------------ 40-240 BEATS/MIN
USING YOUR OMPUTER
The computer can be activated by pressing the button or by receiving the signal from the
speed sensor. If you leave the equipment for 4 minutes, the power will turn off automatically.
BUTTON FUN TIONS:
Press the button to select one of the seven functions of the computer.
Press and hold the button for 3 seconds to reset all data values to zero except the ODOMETER data values.
OMPUTER FUNTIONS:
SCAN: Automatically scans each function in sequence with change every 4 seconds.
NOTE: If you do not want to use the SCAN function, press the button to select one of the other functions.
TIME: Displays your elapsed workout time in minutes and seconds.
SPEED: Displays the current training speed.
DIST (DISTANCE): Displays the cumulative distance traveled during workout.
CAL (CALORIES): Displays approximate amount of calories burned during workout. (This data is a rough
guide for comparison of different exercise sessions and should not be used in medical treatment).
ODO (ODOMETER): Displays the total accumulative distance traveled. The ODOMETER data values cannot
be clear to zero by pressing and holding the button for 3 seconds. If you take out the batteries from the
computer, the ODOMETER data values will clear to zero.
PULSE: Displays your current heart rate figures after you grip the handlebar pulse sensors with both your hands
during exercise. To ensure the pulse readout is more precise, please always hold on to the handlebar pulse
sensors with two hands instead of just with one hand only when you try to test your heart rate figures.
HOW TO INSTALL THE BATTERIES:
1. Remove the battery cover that is located on the back of the computer.
2. Place two "SIZE-AAA" batteries into the battery housing.
3. Insure batteries are correctly positioned and battery springs are proper contact with batteries.

4. Replace the battery cover.
5. If the display is illegible or only partial segment appear, remove batteries and wait 15 seconds before
reinstalling.
STORAGE
Remove the Locking Knob from the Handlebar Support Frame and Main Frame, see Figure 1.
Lift the rear end of the Main Frame up in the vertical position and align Locking Knob hole.
Tighten the Locking Knob by turning it in a clockwise direction into the holes on the left side of the Handlebar
Support Frame and Main Frame, see Figure 2.
AUTION: Failure to secure the Main Frame with the Locking Knob may cause the treadmill accidental
fall and cause bodily injury.
Remove two Handlebar Knobs from the Handlebar and Handlebar Support Frame. Then push the Handlebar all
the way down, see Figure 1.
Install one Handlebar Knob onto the Handlebar Support Frame by turning it in a clockwise direction into the
hole on the top end of the Handlebar Support Frame that was removed, see Figure 2.
Install the other removed Handlebar Knob onto the right side of the Handlebar by turning it in a clockwise
direction into the holes on the Handlebar and Handlebar Support Frame to lock the Handlebar in place, see
Figure 2.
The unit can be carefully tilted onto its transport wheels for easy moving and storage. Store the treadmill in a
clean and dry environment away from children.
NOTE: Do not stand under the main frame when setting down the treadmill.
TO PREVENT INJURY PLEASE MAKE SURE YOU HAVE A FIRM HOLD WHEN LIFTING
UP OR SETTING DOWN THE MAIN FRAME.
Warning: Keep the children and pets away from the folding machine.
Figure 1
Locking Knob
Handlebar Knob
Figure 2
Locking Knob
Handlebar Knob

ADJUSTMENTS
Adjusting the Tension Control Knob
To increase the load, turn the Tension Control Knob in a clockwise direction.
To decrease the load, turn the Tension Control Knob in a counterclockwise direction.
Adjusting the Incline Adjuster
There are 3 incline angles that the incline adjuster can be set to. Loosen the Locking Knob by turning
counterclockwise direction. Place one hand on the rear end of the Main Frame, then lift the rear end of the Main
Frame up and use the other hand to remove the Locking Pins. Adjust the Incline Adjuster to the desired position
and insert the Locking Pins into the holes on the Main Frame and Incline Adjuster to lock the Incline Adjuster in
place. For added safety, tighten the Locking Knob in a clockwise direction.
Adjusting the Running Belt
The running belt is initially set and adjusted at the factory. However it may come loose during transportation
and/or during use. It is recommended that the user run on the center of the running belt. After prolonged use,
the belt will begin to stretch out. It is suggested that the user always to walk or run on the central area. This will
prevent the belt shifting off the center.
Tension Control Knob
Locking Knob

If the running belt begins to shift to the left, the user can stand on the Main Frame and hold the handlebar with
both hands. Then use your right foot to run on the right side of the running belt. You should see the running belt
start to correct itself by moving back towards the center. However, if the running belt is still shifting to the left,
use the Allen Wrench provided and turn the left Rear Roller Adjustment Bolt 1/2 turn in a clockwise direction.
Then try running on the center of the running belt again. If the running belt is still shifting to the left, turn the
left Rear Adjustment Bolt another 1/4 turn in the clockwise direction. Then try running on the center of the
running belt again. You should see the belt start to correct itself by moving back towards the center. Repeat this
procedure until the running belt is centered.
If the running belt begins to shift to the right, the user can stand on the Main Frame and hold the handlebar with
both hands. Then use your left foot to run on the left side of the running belt. You should see the running belt
start to correct itself by moving back towards the center. However, if the running belt is still shifting to the right,
use the Allen Wrench provided and turn the right Rear Roller Adjustment Bolt 1/2 turn in a clockwise direction.
Then try running on the center of the running belt again. If the running belt is still shifting to the right, turn the
right Rear Adjustment Bolt another 1/4 turn in the clockwise direction.
Then try running on the center of the running belt again. You should see the belt start to correct itself by moving
back towards the center. Repeat this procedure until the running belt is centered.
If the running belt is slipping during use, then use the Allen Wrench provided and turn both left and right Rear
Roller Adjustment Bolts 1/4 turn in the clockwise direction. You should now run on the running belt to
determine if the running belt is still slipping. Repeating the above procedure until the running belt is not
slipping.
LUBRI ATION
The treadmill has already been spread with "Silicone Oil" in advance before leaving the manufacturing plant.
Silicone oil is without volatility and has gradually permeated through the running belt. There will be no need to
re-spread the oil in normal circumstances. "Silicone Oil" may be re-spread once the resistance has been
increased and the running belt starts rubbing against the running deck. To hold open the running belt from two
sides, apply the silicone oil with an even motion on the center of the running deck. Allow the silicone oil to ‘set’
for one minute before using the magnetic treadmill.
Attention: Only use "Silicone Oil" lubricants for this equipment. In addition, do not add any other oil
ingredient; otherwise the magnetic treadmill will be damaged. Do not over-lubricate the running deck.
Excess lubricant should be wiped off with a clean towel.

MAINTENAN E
leaning
The magnetic treadmill can be cleaned with a soft clean damp cloth. Do not use abrasives or solvents on plastic
parts. Please wipe your perspiration off the magnetic treadmill after each use. Be careful not get excessive
moisture on the computer display panel as this might cause an electrical hazard or electronics to fail.
Please keep the magnetic treadmill, specially, the computer console, out of direct sunlight to prevent screen
damage.
Please inspect all assembly bolts, nuts, and screws on the machine for proper tightness every week.
Storage
Store the magnetic treadmill in a clean and dry environment away from children.
TROUBLESHOOTING
PROBLEM: Treadmill running belt slips or is not centered on rear roller.
SOLUTION: Refer to “Adjusting the Running Belt” section on page 14.
PROBLEM: Computer not working correctly.
SOLUTION: Check to make sure the computer wires are connected securely.
SOLUTION: Check the batteries are correctly positioned and battery springs are proper contact with batteries.
SOLUTION: Make sure the batteries are not dead.
PROBLEM: There is no heart rate reading or heart rate reading or is erratic / inconsistent.
SOLUTION: Make sure that the wire connections for the hand pulse sensors are secure.
SOLUTION: To ensure the pulse readout is more precise, please always hold on to the handlebar grip sensors
with two hands instead of just with one hand only when you try to test your heart rate figures.
SOLUTION: Gripping the hand pulse sensors too tight. Try to maintain moderate pressure while holding onto
the hand pulse sensors.
PROBLEM: The magnetic treadmill makes a squeaking noise when in use.
SOLUTION: The bolts may be loose on the treadmill, please inspect the bolts and tighten the loose ones.
WARM UP AND OOL DOWN ROUTINE
The WARM-UP is an important part of any workout. The purpose of warming up is to
prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before aerobic
exercising. It should begin every session to prepare your body for more strenuous exercise by heating up and
stretching your muscles, increasing your circulation and pulse rate, and delivering more oxygen to your muscles.
OOL DOWN at the end of your workout, repeat these exercises to reduce soreness in tired muscles. The
purpose of cooling down is to return the body to its resting state at the end of each exercise session. A proper
cool-down slowly lowers your heart rate and allows blood to return to the heart.
HEAD ROLLS
Rotate your head to the right for one count,

feeling the stretch up the left side of your neck, then rotate your head back for one count, stretching your chin to
the ceiling and letting your mouth open. Rotate your head to the left for one count, then drop your head to your
chest for one count.
SHOULDER LIFTS
Lift your right shoulder toward your ear for one count. Then lift your left shoulder up for one count as you lower
your right shoulder.
SIDE STRET HES
Open your arms to the side and lift them until they are over your head. Reach your right arm as far toward the
ceiling as you can for one count. Repeat this action with your left arm.

QUADRI EPS STRET H
With one hand against a wall for balance, reach behind you and pull your right foot up. Bring your heel as close
to your buttocks as possible. Hold for 15 counts and repeat with left foot.
INNER THIGH STRET H
Sit with the soles of your feet together and your knees pointing outward. Pull your feet as close to your groin as
possible. Gently push your knees toward the floor. Hold for 15 counts.
TOE TOU HES
Slowly bend forward from your waist, letting your back and shoulders relax as you stretch toward your toes.
Reach as far as you can and hold for 15 counts.

HAMSTRING STRET HES
Extend your right leg. Rest the sole of your left foot against your right inner thigh. Stretch toward your toe as
far as possible. Hold for 15 counts. Relax and then repeat with left leg.
ALF/A HILLES STRET H
Lean against a wall with your left leg in front of the right and your arms forward. Keep your right leg straight
and the left foot on the floor; then bend the left leg and lean forward by moving your hips toward the wall. Hold,
then repeat on the other side for 15 counts.