Iron Age Office CARRUCA DOGBONE WORKSTATION User manual

CARRUCA DOGBONE
WORKSTATION
Assembly Instructions
Thank you for your purchase!
Iron Age Office furniture is uniquely and individually
fabricated. For this reason, your furniture is pre-assembled
and labeled before shipping. Labels are marked on the
underside of the furniture. Most furniture is then
deconstructed prior to shipping. Pieces that uniquely
correspond can typically be found on the same pallet.
Assembly is best completed by keeping the pieces that
correspond together. Clear your work area of anything that
could scratch furniture surfaces. If possible, cover your
work area with a clean, soft blanket. Carefully flip
any wooden tops over and inspect the bottom sides for markings.
Match legs, flat brackets, etc.
to the appropriate labels.
If you need further assistance of any kind,
please contact:
Iron Age Office Operations Manager
Henry Dover
678-725-1473 (c)
[e-mail]

HARDWARE
Screws are shown actual size. You may receive extra hardware with your unit.
14-10 LAG BOLT
QTY: 82
SCREEN BOLT
QTY: 16
SCREEN NUT
QTY: 16
LEVELING FOOT
QTY: 20 9/16 Crescent Wrench
15/16 Crescent Wrench
3/8 Hex Drive
#3 Square Drive
Tools Required
1
2
3
4
10 TROUGH SCREWS
QTY: 12 #2 Phillips Drive

PARTS
RIGHT TABBED LEG W/
SHEET METAL
LEFT TABBED LEG W/
SHEET METAL MAIN TOP
SECOND TOP
DIVIDER SCREEN
MODESTY SCREEN
1
2
M1
M2
MS
DS
TTROUGH
SHARED LEG
SPLICE PLATE M3
M4
THIRD TOP
FOURTH TOP
RETURN TOP
SECOND RETURN TOP
R1
R2
LEFT TABBED LEG
RIGHT TABBED LEG
3
4
5
5
R1
M3
6
C
7
DS2
8
D
9
M4
T
R2
5
MS4
MS2 T
MS1
MS3
M1
M2
4
B
3
DS1
2
A
1
6
7
RIGHT TABBED LEG W/
SHEET METAL
LEFT TABBED LEG
8
9
RIGHT TABBED LEG
LEFT TABBED LEG W/
SHEET METAL
A
SPLICE PLATE
SPLICE PLATE
SPLICE PLATE
B
C
D

ASSEMBLY
STEP 1
Place wood tops face down on a clean surface.
STEP 2
Align legs using markings on
the underside of the wood tops.
Tabbed legs should be placed so that
tabs are facing each other.
Screw in all legs with
(5) 14-10 lag bolts in each leg.
STEP 3
Screw in (2) leveling feet in each leg.
M4
M3
R1
R2
M2
M1
1
2
3
4
5
9
87
6
5
Screw in (4) 14-10
Lag bolts in each leg
using a #3 square drive.
1
Screw in leveling foot into
each leg with 9/16 crescent wrench.
4

ASSEMBLY
STEP 4
Align splice plates to main tops
using markings on the tops.
STEP 5
Attach screens to tabbed legs
with (4) screen bolts and (4) screen nuts
in each screen.
Insert screen bolts into
the front of the screen
through the tabbed legs
using a 3/8 hex drive.
Fasten screen nut to screen bolt
on backside of screen using a
15/16 crescent wrench.
2
3
STEP 6
Flip M2 and M4 desks
to upright position.
M1
M2
M4
M3
Screw in (3) lag bolts into each
splice plate with a #3 square drive
to secure splice plate to appropriate desks.
1
M2
M4
A
B
C
D
MS1
MS3
MS3
MS4

ASSEMBLY
STEP 9
Flip M1 desk to an upright position and
align to M2 desk. Secure M1 desk
to M2 desk with (3) lag bolts into divider
screen on the underside of
the M1 desk with a #3 square drive.
STEP 8
Align divider screen to M2 desk and R2 return.
STEP 7
Flip and align R2 between M2 and M4.
Screw in (3) lag bolts into each
splice plate with a #3 square drive
to secure splice plate to return desk.
SP
1
M4
M2
R2
Secure divider screen to underside
of M4 desk with (3) lag bolts on each side
with a #3 square drive.
1
M2
R2
DS1
M1
DS1
M2

ASSEMBLY
STEP 11
Flip M3 desk to an upright position and
align to M4 desk. Secure M3 desk to M4
desk with (3) lag bolts into divider screen
on the underside of
the M3 desk with a #3 square drive.
STEP 12
Align R1 between M1 and M3 desks. Secure with
lag bolts into splice plates and divider screens
on the underside of R1.
STEP 10
Align divider screen to M4 desk and R2 return.
Secure with lag bolts on the underside of desk.
M4
DS2
R2
M4
DS2
M3
M3
R1
M1

ASSEMBLY
STEP 13
Align trough to underside of
joined desks using markings.
Screw in (6) trough screws
into each trough using
a #2 phillips drive.
T
10
STEP 14
Enjoy your desk!
CARE INSTRUCTIONS
To care for either wooden or metal surfaces of Iron Age Office products,
gently wipe with a soft cloth dampened with water and a mild dishwashing liquid.
Once satisfied, dry with a soft cloth.
T