Iron Age Office CARRUCA STACK User manual

CARRUCA STACK
WORKSTATION
Assembly Instructions
Thank you for your purchase!
Iron Age Office furniture is uniquely and individually
fabricated. For this reason, your furniture is pre-assembled
and labeled before shipping. Labels are marked on the
underside of the furniture. Most furniture is then
deconstructed prior to shipping. Pieces that uniquely
correspond can typically be found on the same pallet.
Assembly is best completed by keeping the pieces that
correspond together. Clear your work area of anything that
could scratch furniture surfaces. If possible, cover your
work area with a clean, soft blanket. Carefully flip
any wooden tops over and inspect the bottom sides for markings.
Match legs, flat brackets, etc.
to the appropriate labels.
If you need further assistance of any kind,
please contact:
Iron Age Office Operations Manager
Henry Dover
678-725-1473 (c)
[email protected]om

HARDWARE
Screws are shown actual size. You may receive extra hardware with your unit.
14-10 LAG BOLT
QTY: 116
SCREEN BOLT
QTY: 4
SCREEN NUT
QTY: 4
LEVELING FOOT
QTY: 10
Tools Required
#3 Square Drive
3/8 Hex Drive
15/16 Crescent Wrench
9/16 Crescent Wrench
1
2
3
4
10
TROUGH SCREW
QTY: 12
#2 Phillips Drive

PARTS
LEFT TABBED LEG
RIGHT TABBED LEG
LEFT TABBED LEG
SHARED LEG
RIGHT TABBED LEG
DIVIDER SCREEN
TROUGH
SUPPORT BAR
FOURTH TOP
THIRD TOP
SECOND TOP
MAIN TOP
SECOND RETURN TOP
RETURN TOP
1
2
3
4
5
M1
M2
M3
M4
R1
R2
SB
T
DS
THIRD RETURN TOP
R3
FOURTH RETURN TOP
R4
ASPLICE PLATE
1
DS1
M1
5
R1
DS3
R3
B
T
M3
3
2
SB
M2
DS4
T
A
R2
R4
4
DS2
M4
SB
SPLICE PLATE
B

ASSEMBLY
STEP 1
Place wood tops face down on a clean surface.
STEP 2
Align legs using markings on
the underside of the wood tops.
Tabbed legs should be placed so that
tabs are facing each other.
STEP 3
Secure legs to appropriate tops
using 14-10 lag bolts with a #3 square drive.
STEP 4
Screw in (2) leveling feet in each leg.
M1
M2
R1
R3
M3
M4
R4 R1
1
4
3
2
5
Screw in (6) 14-10 Lag bolts
in legs 1,3,4,5, and 6.
Screw in (3) 14-10 Lag bolts
in shared leg 2.
Screw in leveling feet into
each leg with 9/16 crescent wrench.
4
STEP 5
Align splice plates to main tops
using markings on the tops.
M3
M4
1
Screw in (3) lag bolts into each
splice plate with a #3 square drive
to secure splice plate to main desks.
A
B

ASSEMBLY
STEP 6
Flip M3 desk to upright position. Secure but
do not tighten bottom support bar with
(2) screen bolts and (2) screen nuts.
STEP 7
Flip M4 top and align to M3 desk. Secure desks together
with lag bolts into the shared legs on the underside of
M4 top.
3
2
SB
Insert screen bolts into
support bar through the tabbed
legs using a 3/8 hex drive.
Fasten screen nut to screen bolt
on backside of screen using a
15/16 crescent wrench.
M3
SB
M3
M4
Screw in lag bolts into each
shared leg with a #3 square drive
to secure M4 desk to M3 desk.
1
STEP 8
Flip M1 desk to upright position.
Align M1 desk to M3 desk. Secure desks together with
lag bolts into the shared legs and splice plate on the
underside of M1 top.
M3
M1
STEP 9
Secure but do not tighten
bottom support bar with
(2) screen bolts and (2) screen nuts.
SB

ASSEMBLY
STEP 10
Flip and align M2 top to M1 desk.
Secure desks together with lag bolts into the shared legs
and splice plate on the underside of M2 top.
M1
M2
STEP 11
Flip R3 return to upright position.
Align R3 to M3 desk. Secure desks together with lag bolts into the
splice plate on the underside of R3. R3
M3
SP
STEP 12
Flip and align R1 return to R3 and M1.
Secure desks together with lag bolts into the shared legs and splice
plate on the underside of R1.
R3
R1
M1
5
STEP 13
Flip and align R4 desk to M4 desk.
Secure desks together with lag bolts into splice plate on the
underside of R4.
R4
M4
SP

ASSEMBLY
STEP 15
Flip R2 return to upright position.
Align R2 to M2 desk and R4. Secure desks together with lag bolts
into the shared legs and splice plate on the underside of R2.
R4
M2
R2
STEP 16
Align troughs to underside of
joined desks using markings.
T
Screw in (6) trough screws into each trough
using #2 phillips drive.
1
STEP 17
Tighten both bottom support bars.
SB
STEP 18
Align desktop screens to desks.
Screw in (4) lag bolts into
divider screen on each side
with #3 square drive.
1
DS4 DS1
DS3
DS2

ASSEMBLY
STEP 19
Enjoy your desk!
CARE
INSTRUCTIONS
To care for either wooden
or metal surfaces of Iron
Age Office products,
gently wipe with a soft cloth
dampened with water and a
mild dishwashing liquid.
Once satisfied, dry with a
soft cloth.