Iron Age Office CARRUCA User manual

CARRUCA 4 PERSON
WORKSTATION
Assembly Instructions
Thank you for your purchase!
Iron Age Office furniture is uniquely and individually
fabricated. For this reason, your furniture is pre-assembled
and labeled before shipping. Labels are marked on the
underside of the furniture. Most furniture is then
deconstructed prior to shipping. Pieces that uniquely
correspond can typically be found on the same pallet.
Assembly is best completed by keeping the pieces that
correspond together. Clear your work area of anything that
could scratch furniture surfaces. If possible, cover your
work area with a clean, soft blanket. Carefully flip
any wooden tops over and inspect the bottom sides for markings.
Match legs, flat brackets, etc.
to the appropriate labels.
If you need further assistance of any kind,
please contact:
Iron Age Office Operations Manager
Henry Dover
678-725-1473 (c)
[e-mail]

HARDWARE
Screws are shown actual size. You may receive extra hardware with your unit.
14-10 LAG BOLT
QTY: 68
SCREEN BOLT
QTY: 4
SCREEN NUT
QTY: 4
LEVELING FOOT
QTY: 6 9/16 Crescent Wrench
15/16 Crescent Wrench
3/8 Hex Drive
#3 Square Drive
Tools Required
1
2
3
4
10 TROUGH SCREW
QTY: 12 #2 Phillips Drive

PARTS
RIGHT TABBED LEG
LEFT TABBED LEG MAIN TOP
SECOND TOP
DIVIDER SCREEN
1
2
M1
M2
DS
TTROUGH
SB SUPPORT BAR
DS1
DS2
1
M2
T
SB
M1
2
M3
3
SB
T
M4
3
SHARED LEG
M3
M4
THIRD TOP
FOURTH TOP

ASSEMBLY
STEP 1
Place M2 top face down on a clean surface.
STEP 2
Align legs using markings on
the underside of the M2 top.
Tabbed legs should be placed so that
tabs are facing each other.
Screw in all legs with
(6) 14-10 lag bolts in each leg.
M2
M2 2
1
Screw in (6) 14-10
Lag bolts in each leg
using a #3 square drive.
1
STEP 3
Screw in (2) leveling feet in each leg.
Screw in leveling foot into
each leg with 9/16 crescent wrench.
4

ASSEMBLY
STEP 4
Align support bar in between tabbed legs.
Secure but do not tighten support bar with
(2) screen bolts and (2) screen nuts.
STEP 6
Align divider screen to M2 desk.
Secure divider screen to underside of main top
with (4) lag bolts.
SB
2
1
Insert screen bolts into
the support bar through the tabbed
legs using a 3/8 hex drive.
Fasten screen nut to screen bolt
on backside of screen using a
15/16 crescent wrench.
3
2
STEP 5
Flip M2 desk into an upright position.
DS1
M2
M2
Screw in (4) lag bolts into
divider screen on each side
with #3 square drive.
1

ASSEMBLY
STEP 7
Align M1 top to M2 desk. Screw
in (6) lag bolts into each leg and
(4) lag bolts into each side of
divider screen on the underside
of M1 top.
M2
M1
DS1
2
1
Screw in lag bolts into
divider screen and shared legs
on each side with #3 square drive.
1
STEP 8
Flip Leg 3 upside down and screw in
(2) leveling feet.
STEP 9
Flip leg 3 to an upright position.
Align support bar to in between tabbed legs.
Secure but do not tighten support bar with
(2) screen bolts and (2) screen nuts.
3
3
SB

ASSEMBLY
STEP 10
Align M4 top to M2 desk. Screw
in (3) lag bolts into shared leg
and (6) lag bolts into leg 3.
M4
3
M2
2
STEP 11
Align divider screen to M4 desk.
Secure divider screen to underside of
M4 desk with (4) lag bolts.
DS2
M4
STEP 12
Align M3 top to M4 desk. Screw in
(3) lag bolts into shared leg, (6)
lag bolts into leg 3, (4) lag bolts
into divider screen on each side.
M4
DS2
M3
3
2

ASSEMBLY
STEP 10
Align trough to underside of
joined desk using markings.
T
Screw in (6) trough screws into trough
using a #2 phillips drive.
10
STEP 11
Tighten support bars
SB
STEP 12
Enjoy your desk!
CARE INSTRUCTIONS
To care for either wooden or metal
surfaces of Iron Age Office products,
gently wipe with a soft cloth
dampened with water and a mild
dishwashing liquid.
Once satisfied, dry with a soft cloth.