Ironwood GLACIER CDCUR User manual

CDCUR
CDCRR
RISER UNIT
0307
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

A
PARTS DIAGRAM
B
TOP
C
D
M
Left Side 01011642 1 ea.
N
Top CDCUR
Top CDCRR
01050801
01050501
1 ea.
1 ea.
Right Side 01011643 1 ea.
Right Back CDCUR
Right Back CDCRR
01050854
01050554
1 ea.
1 ea.
Left Back CDCUR
Left Back CDCRR
01050854
01050554
1 ea.
1 ea.
Back CDCUR
Back CDCRR
01050852
01050552
1 ea.
1 ea.

H3 Dowel 195000 8 ea.
H2 Minifix Bolt 909834 12 ea.
H1 Minifix Cam 909810 12 ea.
H4 Connector
Screw 950100 4 ea.
ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
HARDWARE

Insert four Minifix Cams (H1) and
screw four Minifix Bolts (H2) into the
Top Panel (C) as shown.
#1
c
H1
H2
H1
TOP
A
B
H3
H3
H3
H2
H3
H3
H3
H2
LEFT SIDE
RIGHT SIDE
#2
Tap in four Wood Dowels (H3) and
screw four Minifix Bolts (H2) into
each Side Panel (A & B) as shown.

#3
#4
D
C
H1
H1
M
H1
H1
LEFT BACK
ND
H1
H1
H1
RIGHT BACKBACK
H1
Insert Minifix Cams (H1)
into each Back Panel
(M,N,D) as shown,
making sure the arrow
faces out toward the edge
of the panel.
Attach the Back Panel (D)
to the Top (C) as shown.
Turn the Minifix Cams
(H1) clockwise to tighten.
#5
D
C
M
H1
Attach the Left Back (M)
as shown. Turn the
Minifix Cam (H1)
clockwise to tighten.

H1
N
Attach the Right Back (N) as shown. Turn the Minifix Cam (H1) clockwise to tighten.
#6
H1
H1
A
Attach the Left Side as shown.
Turn the Minifix Cams (H1)
clockwise to tighten.
#7

Attach the Right Side (B)
as shown. Turn the Minifix
Cams (H1) clockwise to
tighten.
#8
BH1
H1
#9
CDCU or CDCR
FOUR 3/16" HOLES DRILLED THROUGH
FROM PILOT HOLES UNDERNEATH
H4
Drill four holes thru
the desk top of the
CDCU or CDCR as
shown. Turn the
riser unit upright and
attach to the
desktop using four
Confirmat Screws
(H4) as shown.
The installation of your Glacier Corner Riser unit
is now complete and ready to use.
ATTACHING THE UNIT TO THE DESKTOP: