Ironwood TTL User manual

TTL
TABLE TOP
LECTERN
0121
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].

LECTERN Left Side 05870241 1 ea. LECTERN Right Side 05870241 1 ea.
PARTS DIAGRAM
LECTERN Top 05870101 1 ea. LECTERN Back 05870252 1 ea.
AB
CD
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

Place the Left Lectern Side (A), Right Lectern Side (B) and Lectern Back (D) on a
clean, carpeted surface or foam padding with the cam holes upright as shown. Insert
Rafix Cams (H1) into the Left Lectern Side, Right Lectern Side and Lectern Back
where indicated with the arrows of the cams facing out.
#1
AB
D
H1
H1
H1 H1
H1
H2 Rafix Bolt 909925 8 ea.
H1 Rafix Cam 909909 8 ea.
HARDWARE
Screw four Rafix Bolts (H2) into the predrilled holes in the underside of the Lectern Top
(C) where indicated. Screw Rafix bolts into the predrilled holes on the Left Side (A) and
Right Side (B) where indicated.
#2
AB
C
H2
H2 H2 H2
H2
#3
AD
H1
Position the Lectern Back (D) onto the
Left Lectern Side (A) as shown. Turn
the Rafix Cams (H1) to secure.
H6
H6

#4
A
DB
H1
Position the Lectern Side (B) onto the Left
Lectern Back (D) and turn the cams (H1) to
secure.
Position the Rafix bolts (H2) on the
LECTERN Top into the corresponding holes
of the Left Lectern Side (A) and the Right
Lectern Side (B) and turn the cams (H1) to
secure in place.
#5
C
B
D
A
H1
H1
H1
#6 Your Table Top Lectern is now fully assembled
and ready for use.