Ironwood GLACIER LWPS User manual

03/07
LWPS
LAB WORKSTATION
PROCESSOR SHELF
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
B
TOP
Rightside 06002141 1 ea.
A
TOP
Leftside 06002141 1 ea.
C
Top 06002101 1 ea.
E
Bottom 06002101 1 ea.
H2 Leveler Glide 300870 4 ea.
H3 Minifix Bolt 909834 12 ea.
H1 Leveler Insert 274650 4 ea.
H5 Minifix Cam 909810 12 ea.
H4 Wood Dowel 195000 8 ea.
H6 Sleeve
Connector 950200 8 ea.
H7 Connector
Screw 901350 8 ea.

ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
Place the Left Side Panel (A) and the Right Side Panel (B) on a clean, carpeted surface
or foam padding with the pre-drilled holes facing up. Insert the Leveler Inserts (H1) into
the holes in the bottom edges of Left Side Panels (A) and Right Side Panels (B). Using a
plastic mallet, tap until flush with the surface. Screw the Levelers (H2) into the Leveler
Inserts. Adjust Levelers when the assembled unit is in place.
#1
H1
H2

Using a screwdriver, screw six Minifix
bolts (H3) into the Right Side Panel (B)
where indicated. Insert four Wood
Dowels (H4) into the Right Side Panel
(B) where indicated.
#3
H3
Using a screwdriver, screw six Minifix
bolts (H3) into the Left Side Panel (A)
where indicated. Insert four Wood
Dowels (H4) into the Left Side Panel (A)
where indicated.
#2
H4
H3 H4
Place the Top Panel (C) onto a
clean, carpeted surface or foam
padding with the pre-drilled holes
facing up. Insert six Minifix cams
(H5) into the Top Panel (C) with
the arrows of the cams facing out.
#4
H5

Insert six Minifix Cams (H5) into the
Bottom Panel (E) with the arrows of
the cams facing out.
#5
Place the Left Side Panel (A) on a clean,
carpeted surface or foam padding with the
bolts and dowels facing up as shown.
Position the Top Panel (C) onto the Left
Side Panel (A) with the front edges
oriented as shown and turn the arrows of
the Minifix cams (H5) clockwise to secure.
#6
H5
Position the Bottom Panel (E)
onto the Left Side Panel (A) with
the front edges oriented as
shown and turn the arrows of the
Minifix cams (H5) clockwise to
secure.
#7
Position the Right Side Panel (B) onto the unit
and turn the Minifix cams (H5) of the Top Panel
(C) and Bottom Panel (E) clockwise to secure.
Turn the unit upright.
Assembly is now complete.
The next steps show how to connect this unit to
either one or two Lab Workstations.
#8

ADJOINING TO OTHER WORKSTATIONS:
Remove Cable Grommets from the panel
to be connected. The Cable Grommet must
be reinstalled in the other side of the
Processor Shelf unit.
Using a 13/64" bit, drill through the four pilot
holes on the inside of each side panel.
Align the side panels of the units to be
connected. Tap four Connector Sleeves (H6)
throught the holes in one side panel and into
the holes of the unit to be connected. From
the other side, secure the units together using
four connector Screws (H7).
ADJOINING TO OTHER WORKSTATIONS:
Remove Cable Grommets from
the panel to be connected.
Using a 13/64" bit, drill through
the four pilot holes on the inside
of each side panel.
Align the side panels of the
units to be connected. Tap four
Connector Sleeves (H6)
throught the holes in one side
panel and into the holes of the
unit to be connected. From the
other side, secure the units
together using four connector
Screws (H7).
H6 H7
H6 H7