Ironwood CCA User manual

CCA / CCB
COMPUTER
CARRELS
0820
CCA
CCB
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].

PARTS DIAGRAM
A
Left Side-CCA
Left Side-CCB
06000141
06000141
2 ea.
1 ea.
B
C(CCB)
G
Right Side-CCA
Right Side-CCB
06000141
06000141
2 ea.
1 ea.
Worksurface-CCB 06000201 1 ea.
C(CCA)
Divider-CCA
Divider-CCB
06000144
06000252
1 ea.
1 ea.
D
Shelf -CCA
Shelf -CCB
06000127
06000127
2 ea.
1 ea.
Worksurface-CCA 06000101 1 ea.

H3 Upper Leg - CCA
Upper Leg - CCB
1CCLEG
1CCLEG
4 ea.
4 ea.
H4 Lower Leg - CCA
Lower Leg - CCB
1CCLEG
1CCLEG
4 ea.
4 ea.
H5 Allen Head Set Screw - CCA
Allen Head Set Screw - CCB
1CCLEG
1CCLEG
4 ea.
4 ea.
H6 Rafix Cam- CCA
Rafix Cam - CCB 909909 9 ea. 5 ea.
H7 Rafix Bolt - CCA
Raifix Bolt - CCB
909924
909925
11 ea.
13 ea.
H8 Through Bolt - CCA 909852 6 ea.
H9 Confirmat Screw - CCA
Confirmat Screw - CCB
950100
950100
15 ea.
9 ea.
H10 Cord Grommet - CCA
Cord Grommet - CCB
H1480
H1480
2 ea.
1 ea.
H1 Leg Bracket - CCA
Leg Bracket - CCB
300810
300810
4 ea.
4 ea.
H2 Panhead Screw - CCA
Panhead Screw - CCB
901220
901220
24 ea.
24 ea.
HARDWARE
H11 Flush Rafix Cam- CCA
Flush Rafix Cam - CCB 909911 8 ea. 4 ea.

Place the Worksurface (C) face
down on a clean, carpeted surface
with the pre-drilled holes facing up.
Install two Leg Brackets (H1) at
each corner of the Worksurface
using FIVE Panhead Screws (H2) in
the pre-drilled holes as shown.
#1
C
H1
H2
CCA / CCB
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

C
H3
Slide a Lower Leg (H4) into each
Upper Leg (H3). Select the desired
height and secure in place using an
Allen Head Set Screw (H5) as
shown.
Repeat this step on the remaining
legs.
#3
H2
Slide an Upper Leg (H3) into each set of
Leg Brackets (H1) and secure in place
using a Panhead Screw (H2) in the pre-
drilled hole as shown.
#2
CCA / CCB
H4
H3
CCA / CCB
H5

Screw two Rafix Bolts
(H7) into the Left Side
(A) and Right Side (B)
where indicated.
#5
H7
Place the Left Sides
(A), Right Sides (B) and
Shelves (G) as shown.
Insert the Flush Rafix
Cams (H11) into the
sides and Rafix Cams
(H6) into the shelf and
work surface where
indicated.
#4
CCB
CCA
Position a Shelf (G) to a Left
Side (A) with the cord notch
oriented as shown. Secure in
place using the cams.
#6
H6
CORD NOTCH
A
G
H6
C(CCB)

For CCB screw six Rafix Bolts (H7) into the Back (D) where indicated.
#8
A
B
GH6
Place a Right Side (B) onto the other
end of the Shelf (G) as shown.
Secure by turning cams
For the CCA unit repeat Steps 5, 6 &
7 to build the other Shelf-and-Side
assembly.
#7
CCA
CCB
For CCA insert six Through Bolts (H8) into the pre-drilled holes of the Back (D) as shown.

Position the other Shelf-and-
Side assembly onto the other
side of the Back (D) and turn
the cams of the Left Side (A),
Right Side (B) and Shelf (G) to
secure.
#10
Turn the Shelf-and-Side
assembly upright as
shown. Position the Back
(D) onto the assembly and
turn the cams of the Left
Side (A), Right Side (B)
and the Shelf (G) clockwise
to secure.
#9
A
B
D
G
H11
H11
THIS STEP FOR CCA UNIT ONLY
With the assistance of
another person, place
the assembly onto the
Worksurface (C) as
shown. Secure in place
using Confirmat Screws
(H9) through the
Worksurface (C) into
the pre-drilled holes in
the bottom edges of the
Shelf-and-Side
assembly.
#11
H9
H9
CCA
H9
H9
H9
CCB
15 ea H9
9 ea

Press Cord Grommets (H10) into the holes in
the Worksurface (C) as shown.
Your Computer Carrel is now fully assembled and ready for use.
#12
H10
H10
H10