8
Decals
Description Part No.
1 J&M Oval Decal (Large) 9-1/2”x 15” JM0015151
2 www.jm-inc.com Decal JM0019239
3 Danger, Do Not Enter Grain Tank Decal JM0018033
4 Danger, Keep O Ladder Decal JM0018034
5 Warning, Keep Hands Away Decal JM0018039
6 Closed Decal JM0025434
7 Open Decal JM0025433
8 Danger, Electric Lines Decal JM0015099
9 J&M Oval Decal (Medium) 5-1/2”x 8-1/2” JM0010179
10 Danger, Keep Hands and Clothing Away Decal JM0018035
11 California Proposition 65 Warning Decal JM0077568
12 Danger Warning Important Decal JM0037665
13 Lock and Load Indicator Lights Decal JM0044289
1 3 4 5 6 7
89
12
Lock-n-Load
Active
12 Volt
Active
Close Gate ToFold Auger
10
DO NOT ENTER GRAIN TANK WHEN
AUGER IS RUNNING.
KEEP OFF THE LADDER WHILE
THE MACHINE IS OPERATING,
IN TRANSPORT OR THE
UNLOADING AUGER IS IN MOTION
KEEP HANDS AND CLOTHING AWAY
FROM MOVING PARTS
KEEPHANDS AND CLOTHING AWAY
FROMMOVING PARTS
Lock-n-Load
Active
12 Volt
Active
CloseGateToFold Auger
KEEPOFF THE LADDER WHILE
THEMACHINE IS OPERATING,
INTRANSPORT OR THE
UNLOADINGAUGER IS IN MOTION
DO NOT ENTER GRAIN TANKWHEN
AUGER IS RUNNING.
2
Do not inflate tires more than 6 PSI over the recommended
pressure printed on the side of the tire.
CHECK TIRE INFLATION
OPERATING INSTRUCTIONS
Do not operate or service machine until you
read and understand operator’s manual.
Dealer or manufacturer is not responsible for damaged caused by
loose wheel nuts.
CHECK ALL WHEEL NUTS
To prevent serious injury or death:
• Relieve pressure on system before
repairing, adjusting or disconnecting.
• Wear proper hand and eye protection
when searching for leaks.
• Keep all components in good repair.
HIGH-PRESSURE FLUID HAZARD
Do not adjust, service, clear, or lubricate the machine until all
power is shut off.
Keep all safety shields in place.
Keep people and objects clear of equipment before applying
power or moving machine.
Before highway travel, secure a slow-moving vehicle emblem to
the rear of the machine in accordance to the state and local
laws.
Make sure all flashers and turn/brake lights are working properly
BEFORE incidental highway travel.
•
•
•
•
•
FLOWING GRAIN TRAPS AND SUFFOCATESVICTIM IN SECONDS!
With the gate indicator in the closed position, fill the box with
grain.
With the PTO disengaged, fold discharge auger to upright
position.
After auger is in the upright position, start the PTO at a SLOW
RATE OF SPEED untilthe pin on the upper auger engages the
drive dog on the bottom auger(failure to follow this procedure
may cause extensive damage to both the drive dog and the pin).
Increase PTO speed to 1000 RPM and open inner gate until the
pointer is in the halfway position. When grain begins flowing
from the discharge auger, open gate to the full position.
Once the grain has ceased to flow, return the gate to the closed
position (for complete clean-out, gradually close gate, allowing
the opening to be reduced). Disengage the PTO and allow its
rotation to come to a complete stop. Auger is now ready to be
returned to the lowered position.
•
•
•
•
•
SERIOUS INJURY OR
DEATH CAN RESULT WITH
ELECTRIC LINES.
USE CARE WHEN MOVING
OR OPERATING MACHINE
NEAR ELECTRIC LINES TO
AVOID CONTACT.
NEVER PLAY IN OR
ON GRAIN CART YOU CAN DIE IN
SECONDS IN
FLOWING GRAIN!
JM0037665
Donotinflate tires more than 6 PSI over the recommended
pressureprintedon the side of the tire.
CHECKTIRE INFLATION
OPERATINGINSTRUCTIONS
Donot operate or service machine until you
readand understand operator’s manual.
Dealerormanufacturer is not responsible for damaged caused by
loosewheelnuts.
CHECKALL WHEEL NUTS
Topreventserious injury or death:
• Relievepressureonsystem before
repairing,adjusting or disconnecting.
• Wearproperhandand eye protection
whensearching for leaks.
• Keepallcomponentsin good repair.
HIGH-PRESSUREFLUID HAZARD
Donotadjust, service, clear, or lubricate the machine until all
powerisshut off.
Keepallsafety shields in place.
Keeppeopleand objects clear of equipment before applying
powerormoving machine.
Beforehighwaytravel, secure a slow-moving vehicle emblem to
therearof the machine in accordance to the state and local
laws.
Makesureall flashers and turn/brake lights are working properly
BEFOREincidentalhighway travel.
•
•
•
•
•
FLOWINGGRAINTRAPS AND SUFFOCATES VICTIM IN SECONDS!
Withthegate indicator in the closed position, fill the box with
grain.
WiththePTO disengaged, fold discharge auger to upright
position.
Afteraugeris in the upright position, start the PTO at a SLOW
RATEOFSPEED until the pin on the upper auger engages the
drivedogon the bottom auger(failure to follow this procedure
maycauseextensive damage to both the drive dog and the pin).
IncreasePTOspeed to 1000 RPM and open inner gate until the
pointerisin the halfway position. When grain begins flowing
fromthedischarge auger, open gate to the full position.
Oncethegrain has ceased to flow, return the gate to the closed
position(forcomplete clean-out, gradually close gate, allowing
theopeningto be reduced). Disengage the PTO and allow its
rotationtocome to a complete stop. Auger is now ready to be
returnedtothe lowered position.
•
•
•
•
•
SERIOUSINJURY OR
DEATHCAN RESULTWITH
ELECTRICLINES.
USECARE WHEN MOVING
OROPERATING MACHINE
NEARELECTRIC LINES TO
AVOIDCONTACT.
NEVERPLAY IN OR
ONGRAIN CART YOUCANDIE IN
SECONDSIN
FLOWINGGRAIN!
JM0037665
13
WARNING
THIS PRODUCT MAY CONTAIN ACHEMICAL
KNOWN TO THE STATE OF CALIFORNIA TO CAUSE
CANCER, BIRTH DEFECTS, OR OTHER
REPRODUCTIVE HARM.
CALIFORNIA PROPOSITION 65 WARNING
For more information: www.p65warnings.ca.gov
THISPRODUCT MAYCONTAIN A CHEMICAL
KNOWNTO THE STATEOF CALIFORNIA TO CAUSE
CANCER,BIRTH DEFECTS, OR OTHER
REPRODUCTIVEHARM.
CALIFORNIAPROPOSITION 65 WARNING
Formoreinformation: www.p65warnings.ca.gov
11
ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
Replace Immediately If Damaged or Missing
