John Lewis IL4017 User manual

IL4017
Recommended bulb
2 x 3-4 Watt SES energy efficient LED CNDL
or
2 x 28 Watt SES eco halogen CNDL
Bulb not included
Specification
Max power: 28W
Voltage: 220~240V, 50Hz
IP20
Weight 2.4Kg
Please retain these instructions for future reference.
This symbol indicates that this product should not be treated as normal house-hold
waste and it should be recycled. John Lewis does not operate in store take back, but
as members of the Distributer Take Back scheme have funded the development and
upgrade of recycling facilities across the UK. Please take it to your nearest collection
facility or for further details contact your local council or visit www.recycle-more.co.uk.
We have taken great care to ensure that this product reaches you in perfect
condition. However, should any parts be damaged or missing please e-mail
[e-mail]
Trouble shooting:
Why is the light not working when switched on?
Check your power supply is switched on
Turn off light and check that the bulb is inserted correctly
Check the bulb is still in working order.
John Lewis partnership
171 Victoria Street
London SW1E 5NN
Johnlewis.com
Made in China
Issue 2 05/18
User manual
ALICE PIERCED
SHADE FLOOR

IL4017
Thank you for purchasing this Alice pierced shade floor lamp. Please read the
instructions carefully before use to ensure safe and satisfactory operations of this
product.
Please keep this instruction for future reference.
Warnings!
The supply cable runs through the inside of this product. Take care not to place
undue stress on the cable whilst unpacking to prevent the possibility of a poor
connection.
If you are in any doubt consult a person competent to give advice on the
assembly of electrical equipment.
If the external flexible cable of the lamp is damaged it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in
order to avoid a hazard.
To prevent electrocution switch off at the mains supply before assembling or
maintaining this fitting. Ensure the plug is not connected to any power supply and
read instructions before assembly.
Always be sure to use the correct type and wattage of bulbs as indicated on the
fitting. Never exceed the wattage stated.
When changing the bulb, always switch off at the mains and allow the old bulb to
cool down before handling. Dispose of used bulbs carefully.
Caution! The bulb and surrounding parts can become hot during use.
For indoor use only.
Care instructions
We recommend cleaning with a soft dry cloth. Do not use abrasive materials as
these will damage the finish.
Replace bulbs from John Lewis or established brand of the same type and
compatibility.
Parts list
Assembly
Never assembly your appliance on a wet, freshly painted surface. Ensure to switch
off at the mains supply before assembling or maintaining this fitting.
Step 1
Unpack the product and remove all packaging. Be
careful not to scratch the surface of the product whilst
removing the wrapping.
Lay the product out on the floor. If the floor is not
carpeted please cover it with a soft cloth to avoid
damage to the flooring and surface of the product.
Assembly should take place with the product lying flat.
Screw the lower pole onto the upper lamp holder
section ensuring that the lamp holder section is kept still
and that the pole is threaded on ensuring that the cable
does not twist.
Step 2
Gently pull any excess supply cable through the small
hole in the base until it meets the pole assembly.
Place the self-adhesive protective pad to the bottom of
the base.
Note: Peel the cover from the protective base pad and
apply evenly.
Stand the floor lamp upright and ensure all the
assembled parts are fully tightened.
Step 3
To fit shade: Lower the shade over the lampholder
section and align the screw holes at the base of the
shade with those in the frame just below the lamp
holder. Insert the three thumb screws through the
underside of the lamp holder frame section and into
the threaded holes in the lower frame and tighten
screws to secure in place.
Fit the bulb, type and wattage as indicated on the
fitting (bulb not supplied). The wattage indicated must
not be exceeded.
Floor lamp is now ready for use.