JUMO JUMO dTRANS p20 DELTA User manual

40302500T90Z001K000
V10.00/EN/00525980/2022-10-04
JUMO dTRANS p20
Process pressure transmitter
Operating Manual

Contents
Contents
1 Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Hazardous materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1 Areas of application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.2 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
3 Identifying the device version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.1 Nameplate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
3.2 Order details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
3.3 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.4 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
3.5 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
3.5.1 Process connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
4.1 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
4.2 Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
4.3 Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
4.4 Voltage supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
4.5 Mechanical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
4.6 Environmental influences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
4.7 Accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
4.8 Approvals and approval marks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
5 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
5.1 Before mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
5.2 Unscrew the front ring or case lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
5.3 Rotating the LCD (display) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
5.4 Rotating the housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
5.5 Pressure connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
5.6 Measuring the relative or absolute pressure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
5.7 Bracket for wall and pipe mounting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
5.8 Level measurement with or without a pressure separator . . . . . . . . . . . . . . . . . . . . . . . . . .36
5.8.1 General information for a system with a diaphragm seal . . . . . . . . . . . . . . . . . . . . . . . . . . .37
5.9 Assembly in the explosion area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
6.1 Installation notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
6.2 Device with cable gland . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
6.3 Device with M12 connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
6.4 Electrical connection in Ex areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
6.4.1 Connection diagram "Ex" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Contents
7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
7.1 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
7.2 Operation with rotary knob or with setup programm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
7.3 The level concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
7.3.1 The display level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
7.3.2 The parameter level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
8 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
8.1 Data flow diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
8.2 Description of the possible configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
8.3 Level measurement configuration with a pressure specification - recommended (tank emp-
ty, tank full) 60
8.4 Level measurement configuration without a pressure specification with or without a dia-
phragm seal 61
9 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
9.1 Overcoming errors and malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
10 HART® 7 specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
10.1 Device identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
10.2 Variable codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
10.3 HART® commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
10.4 Burst mode commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
10.5 Performance data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
11 Declaration of conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
12 Examination certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
13 DNV GL Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
14 China RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

5
1 Safety information
1 Safety informat ion
General
This manual contains information that must be observed in the interest of your own safety and to avoid
material damage. This information is supported by symbols which are used in this manual as indicated.
Please read this manual before starting up the device. Store this manual in a place that is accessible to
all users at all times.
If difficulties occur during startup, please do not intervene in any way that could jeopardize your warranty
rights!
Warning symbols
DANGER!
This symbol indicates that personal injury from electrocution may occur if the appropriate precaution-
ary measures are not taken.
CAUTION!
This symbol in connection with the signal word indicates that material damage or data loss will occur
if the respective precautionary measures are not taken.
Note symbols
NOTE!
This symbol refers to important information about the product, its handling, or additional benefits.
1.1 Hazardous materials
Using hazardous materials as a medium may result in abrasive and corrosive damage to components
of the product that come into contact with the medium. The medium may leak and present a fire hazard
and a risk to health.
Carry out a risk assessment taking into consideration the safety data sheet for the relevant hazardous
substance for mounting, operation, maintenance, cleaning, and disposal:
• Comparison and systematic checking of the durability of the components of the product that come
into contact with the medium and the admissible environmental influences.
• Assessment of the risk to people and the environment.
• Assessment of the fire hazard due to the product materials, the admissible environmental influences,
and the voltage supply.

1 Safety information
6

7
2 General information
2 General information
DANGER!
The device is suitable for measuring pressure in gases and liquids without solids content.
In the SIL version (functional safety), this device is used in safety-related systems for minimum,
maximum and area monitoring that fulfil the requirements of the series of standards
IEC 61508:2010.
A failure of the device or other devices connected to it, e.g. due to an operating error, can lead to
dangerous malfunctions of the whole plant.
Therefore please also observe the corresponding safety manual from the device series.
NOTE!
Read this operating manual before putting the device into service. Keep the operating manual in a place
that is accessible to all users at all times.
All necessary settings are described in this operating manual. Nevertheless, should problems be en-
countered during startup please do not make any unauthorized manipulations. This could endanger your
rights under the warranty!
Please contact the nearest branch office or the head office.
2.1 Areas of application
The device with the HART® interface combines maximum precision with simple operation. It is used to
measure the system pressure of gas, steam and liquids. The built-in LCD displays measured values and
device data. The device can be installed up to zone 0 in the version with explosion protection "Ex ia (in-
trinsically safe)".
The housing and sensor are manufactured from high-grade stainless steel. Diaphragm seals can also
be connected for specific process technology applications (see data sheets 409772 to 409784).
The pressure transmitter can be programmed and can therefore be flexibly adapted for various measur-
ing tasks. There is an easy-to-use setup program available as an accessory for operation via interfaces.
A rotary knob allows for quick and easy on-site manual operation.
The pressure transmitter with 4 to 20 mA and HART® protocol was evaluated with regard to functional
safety and is certified by exida according to IEC 61508/-1/-2/-3. These measuring devices are suitable
for monitoring process level and process pressure up to SIL2. Further details can be found in the Safety
Manual.
Use in "Ex-area"
In the Ex ia version, the device is permitted for use in the "Ex-area" if it has a corresponding identification
marking on the nameplate.
For the special conditions for use, the examination certificate must be observed.
 chapter 12 "Examination certificate", Page 75
Functional safety use
In the SIL version, the device is permitted for use according to IEC 61508 if it has a corresponding iden-
tification marking on the nameplate.
Application areas
The device can be used for various applications, e.g.
• For level measurements
• For foam formation
• In containers with mixers or sieve installations
• For liquid gases

2 General information
8
Measured process variables
Pressure
Calculated process variables
Filling level (level, volume or mass)
CAUTION!
The device's membranes must not be damaged at the process connection!
Do not insert any objects into the drilled holes of the pressure connections!
The device must be sent back if there is damage to the housing or membrane!

9
2 General information
2.2 Scope of delivery
Operating Manual
The operating manual describe the mounting, the electrical connection, the startup and operation of the
device.
Safety manual (option)
The safety manual describes the safe application with the installation according to IEC 61508.
Calibration certificate
The device is supplied with a calibration certificate and a setup print-out.
These documents contain information about the set parameters and/or the measured parameters for the
respective device.
If the calibration certificate is lost or if you need another copy, the calibration certificate can be requested
from the manufacturer by specifying the device's F number (see nameplate). You will find the supplier's
address on the back cover of the manual.
Setup program (option)
The setup program is available as an option: part no. 00537577
All the device's parameters can be conveniently checked and adjusted using the setup program - there
are also additional functions, e.g.:
• Recording the measured values
• Graphical view of temperature and pressure
• Detailed diagnostic messages
• Display of the complete order code and the device configuration (for follow-up orders)
The setup program accesses the device via
• the JUMO interface (standard) or
• the HART® interface (optional)
DANGER!
The JUMO interface must not be used in the Ex-area!
The device may only be operated using the rotary knob or the HART® interface!
PC interface cable (option)
Available as an accessory: PC interface cable with USB/TTL converter and two adapters (USB transmit-
ter cable), part no. 00456352.
The device can be connected to a PC's USB port via the JUMO interface with the PC interface cable.
HART® modem (option)
Available as an accessory: HART® modem for USB, part no. 00443447.
The device can be connected to a PC's USB® port via the HART® interface with the HART® modem.
Input isolating amplifier (option)
Available as an accessory: Input isolating amplifier for Ex-applications, HART®-capable, part no.
00577948.
Devices with explosion protection ATEX Ex ia must be connected via an input isolating amplifier for use
in the Ex-area!

2 General information
10
Diaphragm seal (option)
Available as an accessory: see data sheets 409770 to 409786.
Diaphragm seals are used for adjusting to particular applications if conventional pressure connections
cannot be used.
CAUTION!
Diaphragm seals are installed by default and must not be removed from the device!
Valve manifolds (option)
Available as an accessory: see data sheet 409706.
JUMO PEKA – Hygienic process connection (option)
Available as an accessory: see data sheet 409711.
Additional JUMO accessories (option)
Additional accessories available: see data sheet 409700 (shut-off valves, measurement device holders,
transition pieces, seals, etc.).

11
3 Identifying the device version
3 Identi fying t he device version
3.1 Nameplate
Housing
Sample identification marking on the device housing
Date of manufacture
The device's date of manufacture (year and calendar week) is part of the fabrication number. Numbers
12 to 15 denote the year of manufacture and the calendar week.
(1) Fabrication number (2) Output signal
(3) Voltage supply (4) Nominal measuring range
(5) Default measuring range (6) Part number
(7) Type
(6)
(5)
(4)
(3)
(2)
(1)
(7)

3 Identifying the device version
12
3.2 Order details
(1) Basic type
403025 JUMO dTRANS p20 - process pressure transmitter
(2) Basic type extension
0 None
2SIL
a
9 Special version
(3) Explosion protection
0 None
1 ATEX Ex iab
(4) Housing
1 Short, stainless steel, with M12 connectionc
2 Long, stainless steel, with cable fitting
3 Precision casting, with cable fitting
(5) Electrical connection
36 Round plug M12 × 1c
82 Plastic cable fitting
93 Metal cable fitting
(6) Cover material
20 CrNi (stainless steel)
85 Plastic
(7) Display
0 None
1 With display (LCD)
(8) Operation
0 None
1 With control knob
(9) Input – nominal measuring range
450 -600 to +600 mbar relative pressure
473 -1 to +2.5 bar relative pressure
513 -1 to +4 bar relative pressure
472 -1 to +10 bar relative pressure
514 -1 to +25 bar relative pressure
515 -1 to +100 bar relative pressured
508 -1 to +250 bar relative pressuree
516 -1 to +600 bar relative pressuree
487 0 to 0.6 bar absolute pressure
490 0 to 2.5 bar absolute pressure
491 0 to 4 bar absolute pressure
493 0 to 10 bar absolute pressure
495 0 to 25 bar absolute pressure
507 0 to 100 bar absolute pressured
(10) Output
405 4 to 20 mA, two-wire
410 4 to 20 mA, two-wire with HART® protocol

13
3 Identifying the device version
(11) Process connection
504 G 1/2 according to DIN EN 837
512 1/2-14 NPT according to DIN EN 837
559 M20 × 1.5 according to DIN 3852-11
564 1/2-14 NPT internal
571 G 3/4 front-flush according to DIN EN ISO 228-1
583 M20 × 1.5 with pin
604 Taper socket with union nut DN 25 according to DIN 11851 (dairy pipe fitting)
606 Taper socket with union nut DN 40 according to DIN 11851 (dairy pipe fitting)
613 Clamp connection (clamp) DN 25 according to DIN 32676
616 Clamp connection (clamp) DN 50 according to DIN 32676 (2“ ISO 2852)
652 Tank connection with grooved union nut DN 25
997 JUMO PEKA – Hygienic process connection
998 Diaphragm seal version, screwed
(12) Medium temperature
1 Up to 120 °Cb
2 Up to 200 °Cb
(13) Process connection material
20 CrNi (stainless steel)
82 NiMof
(14) Measuring system, filling medium
00 None
01 Silicon oil
(15) Extra codes
100 Customer-specific factory settingg
226 GOST/EAC approvalh
374 Inspection certificate 3.1 DIN EN 10204 material
452 Electrolytically polished parts
591 Choke in the pressure channel
624 Oil and grease free
630 Enlarged pressure channel
634 TAG number
635 NACE manufacturer's declarationi
681 Expanded admissible ambient temperature
691 Improved moisture and vibration protection
880 DNV GL approvalj
aOnly available with output 410 and display 1. Not available with input 508 and 516 and also with extra code 681.
bOnly available with output 410. Not available with electrical connection 82 and cover material 85. The medium tem-
perature 1 is valid until 115 °C. The medium temperature 2 is valid until 175 °C.
cThe housing 1 is only available with electrical connection 82 and vice versa.
dNot available with process connection 604, 606, 613, 616.
eNot available with process connection 571, 604, 606, 613, 616, 997.
fNot available with input 450, 573, 513, 572, 487, 490, 491, 493.
gPlease specify the setting you want in plain text. For default setting see “Accuracy” section in the data sheet.
hAvailable upon request.
iOnly available with process connection 512, 564 and process connection material 82. Not available with input 450,
487.
jOnly available with explosion protection 1. Not available with input 516.

3 Identifying the device version
14
3.3 Accessories
3.4 Software
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14) (15)
Order code /--- - --- - - - - - /
Order example 403025 / 0 - 0 - 2 - 82 - 85 - 1 - 1 - 514 - 405 - 504 - 1 - 20 - 1 / 000
Designation Part no.
4-pole cable box, straight, M12 × 1 with 2 m PVC cable 00404585
4-pole cable box, angled, M12 × 1 with 2 m PVC cable 00409334
PC interface with USB/TTL convertera00456352
HART® modem USBb00443447
Ex-i repeater power supply/input isolating amplifier, data sheet 707530 00577948
Measuring device holder for wall and 2" pipe 00597711
Designation Data sheet
Valve manifolds 409706
JUMO PEKA – Hygienic process connection 409711
Diaphragm seal with dairy pipe fitting DIN 11851 409772
Diaphragm seal with clamp connection 409774
Diaphragm seal with DRD flange or VARIVENT® socket 409776
Diaphragm seal with ISS/SMS/RJT socket and (grooved) union nut 409778
Membrane diaphragm seal 4MDV-10 409780
Diaphragm seal with screw-in thread DIN ISO 228/1 or ANSI B1.201 409782
Diaphragm seal with flange connection DIN EN 1092-1 with sealing strip form B1 409784
Diaphragm seal with flange connection according to ANSI B 16.5 with sealing strip form RF 409786
Ex-i repeater power supply/input isolating amplifier 707530
aThe PC interface cable is the connection between the JUMO interface of the differential pressure transmitter and
the USB interface of a PC.
bThe HART® modem is the connection between the HART® interface of the differential pressure transmitter and
the USB interface of a PC.
Description Part no.
JUMO setup dTRANS p20 series 00537577
Device Type Manager (DTM), JUMO dTRANS p20 00738288

15
3 Identifying the device version
3.5 Dimensions
Type 403025/0-0-1 (short, stainless steel, with M12 connection)
Type 403025/0-0-2 (long, stainless steel, with cable fitting)
A M20 × 1.5 cable fitting
86.5
113
138
104
64
ø 73
113
A

3 Identifying the device version
16
Dimensions at medium temperature 2 (high-temperature version)
Pressure transmitters that are suitable for medium temperatures up to 200 °C have an extended shaft
through which the increased temperature is discharged. The total height of all pressure transmitters in
this version increases by 41 mm as shown in the following figure.
Type 403025/0-0-3 (precision casting, with cable fitting)
A M20 × 1.5 cable fitting
145
116
66
109
ø 73
A
A M20 × 1.5 cable fitting
138
73
64
104
153
41
A

17
3 Identifying the device version
3.5.1 Process connections
504 512 564
G 1/2 1/2-14 NPT 1/2-14 NPT internal
G 1/2
20
30.5
1/2-14 NPT
30.5
20
SW 27
23.5
1/2-14 NPT
571 583
G 3/4 M20 (× 1.5) with pin
32
16
SW 32
G 3/4
M20x1,5
30.5
20

3 Identifying the device version
18
Dimensions of the process connections 604, 606, 613, and 616
604 and 606 613 and 616
Taper socket with grooved union nut according to DIN 11851 Clamp according to DIN 32676
L1
L2
15
D2
D1
652 997
Tank connection with grooved
union nut DN 25
JUMO PEKA
RD52 x1/6
35
45
55
63
21
31
31.5
SW 27
11
ConnectionDND1D2D3 D4L1L2
604 25 Ø 44 Ø 35 Rd 52 × 1/6“ Ø 63 15 21
606 40 Ø 56 Ø 48 Rd 65 × 1/6“ Ø 78
613 25 Ø 43,5 Ø 50.5
616 50 Ø 56,5 Ø 64

19
4 Technical data
4 Technical d ata
4.1 General Information
Reference conditions DIN EN 60770 and DIN EN 61298
Ambient temperature 22 °C ±5 K
Air pressure 1000 hPa (±25 hPa)
Voltage supply DC 24 V
Burden 50 Ω
Sensor system Silicon sensor with stainless steel separating diaphragm/thin film sensor
Pressure transfer medium
For measuring system filling medi-
um 0
Without transfer medium
For measuring system filling medi-
um 1
Silicon oil, FDA compliant
Admissible load changes > 10 million
Position
Mounting position Any
Calibration position Device upright, process connection at the bottom
Zero offset depending on position Relative pressure: a zero offset is possible on-site or via setup.
Absolute pressure: manual readjustment is possible.
For medium temperature 1
(up to 120 °C)
≤1mbar
For medium temperature 2
(up to 200 °C)
≤10mbar
DisplayaLCD, two-line with bar graph
Alignment Display unit rotatable in 90° steps
Housing rotatable ±160°
Size Display 22 × 35 mm, font size 7 mm, 5 digits
Color Black
Portrayable measuring units
Input pressure mH2O, inH2O, inHg, ftH2O, mmH2O, mmHg, psi, bar, mbar, kg/cm2, kPa, Torr,
MPa
Measured value % or scaled with freely adjustable measuring unit
Output current mA
Sensor temperature °C, °F
Additional display data Minimum pressure, maximum pressure, error, overrange, underrange, operat-
ing hours, device parameters
Operation
On-site With rotary knob and LCD
Setup program Via interface
Interface
Standard JUMO interfaceb
For output 410 (4to20mA with
HART®)
JUMO interfaceb and HART® interface
aoptional; SIL version only available with display
bThe JUMO interface may not be used in a potentially explosive area! In such a case the device can be operated
via the rotary knob or the HART® interface.

4 Technical data
20
4.2 Input
4.3 Output
4.4 Voltage supply
Relative pressure
Nominal measuring
range
-600 to +600 mbar -1 to +2.5 bar -1 to +4 bar -1 to +10 bar
Overload capability 6 bar 15 bar 30 bar 60 bar
Burst pressure 12 bar 30 bar 60 bar 100 bar
Relative pressure
Nominal measuring
range
-1 to +25 bar -1 to +100 bar -1 to +250 bar -1 to +600 bar
Overload capability 150 bar 300 bar 600 bar 1200 bar
Burst pressure 250 bar 400 bar 700 bar 2000 bar
Absolute pressure
Nominal measuring
range
0 to 0.6 bar 0 to 2.5 bar 0 to 4 bar 0 to 10 bar 0 to 25 bar 0 to 100 bar
Overload capability 6 bar 15 bar 30 bar 60 bar 150 bar 300 bar
Burst pressure 12 bar 30 bar 60 bar 100 bar 250 bar 400 bar
analog output
For output 405 (4 to 20 mA) 4 to 20 mA, 2-wire
For output 410
(4 to 20 mA with HART®)
4 to 20 mA, two-wire with HART® version 7
Jump response time T60 ≤ 190 ms without attenuation
Attenuation Adjustable 0 to 100 s
Burden
For output 405 (4 to 20 mA) Burden ≤ (UB-12V)÷0.022A
For output 410
(4 to 20 mA with HART®)
Burden ≤ (UB-12 V) ÷ 0.022 A; additional: min. 250 Ω, max. 1100 Ω
For version
Explosion protection 0 (without) DC 12 to 36 V
Explosion protection 1 (ATEX Ex ia) DC 12 to 28 V
The voltage supply must be intrinsically safeand must not exceed the following
maximum values:
Ui ≤ DC 28 V
Ii ≤ 115 mA
Pi ≤ 750 mW
Ci = 6 nF
Li = 105 µH