KI Aristotle Casegoods Conference Table User manual

Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Single-Piece Conference Table
Assembly
Note: If a two-piece conference table
is being assembled go to page 2:
“Two-Piece Conference Table
Assembly.”
1. Carefully unpack all parts and
identify the hardware required below
from the “Hardware Pack” diagram.
Set tabletop upside down on a soft
protective surface.
Note: One hardware pack is
supplied per table base, to secure
each base to the tabletop underside.
2. Insert and twist four shoulder pin
screws into the 5mm diameter
pre-drilled holes in the underside of
the tabletop as illustrated (Figure 1
& Detail A).
3. Carefully turn each table base upside
down onto the tabletop one at a time,
inserting the shoulder pin screws
of the table into the corresponding
camlock holes at the top edge of
the table bases. Open the table base
door and locate the camlocks inside
the base, then twist each camlock
clockwise to the 2 O’Clock position
to lock (Figure 1 & Detail B).
4. Once table bases are camlocked
to the tabletop, identify the angle
brackets inside the base, then twist in
and tighten two #8 x 1” RWH screws
per bracket, to further secure the
base to the underside of the table as
illustrated. After all 8 screws per base
are tight, close the table base door
(Figure 1 & Detail C).
5. With the assistance of a second
person, carefully turn the table
upright and level the table as
required.
Figure 1
Detail C
table base
tabletop
shoulder
pin screw
#8 x 1”
RWH screw
angle
bracket
cam
Detail A
shoulder
pin screw
Detail
B
Step 1 Step 2
Rotate Camlock to
the 2 O’Clock position
to lock.FULLY
2 O’Clock
shoulder
pin screw 7HP39 - Hardware Pack
shoulder pin
screw
#8 x 1” RWH
screw
4
8
(one per base)
Assembly Instructions
Aristotle®Casegoods
Conference Tables
January 2017

2
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
tabletop
tabletop
Figure 2
Two-Piece Conference Table
Assembly
1. Carefully unpack all parts and
identify the hardware required below
from the “Hardware Pack” diagram.
Set tabletops upside down on a soft
protective surface.
Note: One hardware pack is
supplied per table base, to secure
each base to the tabletop underside.
Another hardware pack is supplied
when two table surfaces must be
joined together.
2. To join two-piece table halves
together, first align the surfaces to
be joined so the holes for the joint
fasteners face each other. Then slide
both worksurface halves together
and align edges perfectly to each
other (Figure 2).
3. Locate the joint fasteners hardware
pack. If not pre-assembled, loosely
twist joint fastener connector plates
onto each toggle bolt, then set
the joint fastener assembly into
the bored holes and slots in the
worksurfaces as illustrated. Using
a wrench, tighten the toggle bolt to
bring worksurface halves together,
taking great care to make sure
edges and table surfaces are aligned
perfectly (Figure 3 & Detail D).
Aristotle®Casegoods - Two-Piece Conference Table
Assembly Instructions
tabletop
tabletop
Figure
3
joint fastener
with connector
plates
connector
plate
Detail D
joint
fastener
7HP39 - Hardware Pack
shoulder pin
screw
#8 x 1” RWH
screw
4
8
(one per base)
7HP18 - Hardware Pack
joint fastener
splice plate
2
4
(two-piece conference table)
#8 x 1” RWH
screw 32

3
Assemble units as described herein only. To do otherwise
may result in instability. All screws, nuts and bolts must be
tightened securely and must be checked periodically after
assembly. Failure to assemble properly, or to secure parts
may result in assembly failure and personal injury.
Aristotle®Casegoods - Two-Piece Conference Table
Assembly Instructions
table base
shoulder
pin screw
Figure
4
#8 x 1”
RWH screw
tabletop
tabletop
splice
plate
cam
Detail E
shoulder
pin screw
cam
Detail F
#8 x 1”
RWH screw
angle
bracket
cam
4. With table halves joined together
tightly and precisely, align the four
splice plates over the pre-drilled
holes at each side of the joint
fasteners as illustrated, then tightly
secure each splice plate using eight
#8 x 1” RWH screws, four per splice
plate side as illustrated (Figure 4).
5. At each base installation location,
insert and twist four shoulder pin
screws into the 5mm diameter
pre-drilled holes in the underside
of the joined tabletops as illustrated
(Figure 4).
6. Carefully turn each table base upside
down onto the tabletop underside
one at a time, inserting the shoulder
pin screws of the worksurface into
the corresponding camlock holes
at the top edge of the table bases.
Open the table base door and locate
the camlocks inside the base, then
twist each camlock clockwise to the
2 O’Clock position to lock (Figure 4
& Detail G).
7. Once table bases are camlocked
to the joined tabletops, identify the
angle brackets inside the base, then
twist in and tighten two #8 x 1”
RWH screws per bracket, to further
secure the base to the underside
of the worksurface as illustrated.
After all 8 screws per base are tight,
close the table base door (Figure 4
& Detail F).
8. With the assistance of two or
more people, carefully turn the
table upright and level the table as
required.
Detail G
Step 1 Step 2
Rotate Camlock to
the 2 O’Clock position
to lock.FULLY
2 O’Clock
shoulder
pin screw

1330 Bellevue Street • P.O. Box 8100 • Green Bay, WI 54308-8100 • Tel [phone] • www.ki.com
© 2017 Krueger International, Inc. All Rights Reserved • Code KI-AI-000003/KI/PDF/0117
Aristotle®Casegoods - Conference Table
Assembly Instructions