Kohler MEMOIRS K-36937T User manual

, 2013
Copyright Kohler China Ltd., 2013
MEMOIRS
SINGULIER
INSTALLATION INSTRUCTIONS
L 8mm
HINGED, L-SHAPE, 2DR2PAN, 8mm
K-36937T/K-36951T
L 10mm
HINGED, L-SHAPE, 2DR2PAN, 10mm
K-36944T/K-36958T
-1-
13-1 528437
·
·
·
·
·
·
2
80mm
3mm/m
·
·
·
·
·
·
Before you install your shower door, please read
these instructions carefully to familiarize yourself
with the required tools, materials, and installation
sequences. Follow the sections that pertain to your
particular installation. This will help you avoid costly
mistakes. In addition to proper installation, read all
operating and safety instructions.
All information is based on the latest product
information available at the time of publication.
Kohler China Ltd. reserves the right to make
changes in product characteristics, packaging, or
availability at any time without notice.
These instructions contain important care, cleaning,
and warranty information-
Make sure that the bath and the finished wall
material are completely and correctly installed prior
to installing your shower door. Prepare waterproof
layer to wall and floor of the showering area. It is not
allowed for any presence of electric switches and
sockets. Make sure the floor drain runs smoothly.
Before starting the door installation, lay out and
identify all the parts. Use the exploded view
illustrated on page 2 for reference.
For the installation method of customized shower
with different dimensions, please refer to this
instructions.
Tempered glass cannot be cut, drilled or knocked
by hard object. Make sure corner area of the
glass refraining from knocking so as to cause
personal injury due to broken glass.
Please install this door on Kohler
receptors or curbs (Not included). If the curb is not
Kohler-branded, please note its top width should fall
above 80mm.
The shower door requires a flat vertical
finished wall. The squareness of the wall is
recommended no more than 3 mm/m. KOHLER
Company won't take responsibility of the installation
quality.
please leave these
instructions for the consumer.
CAUTION: Risk of injury or product damage.
ATTENTION:
IMPORTANT:
1172434-T01-B

-2-
ROUGHING-IN
Unit: mm
PARTS IDENTIFICATIONPARTS IDENTIFICATION
ABHSKU
K-36937T
K-36951T
K-36944T
K-36958T
800-1300 800-1300 1850-2000
K-36937T/K-36951T
MEMOIRS Bracket Assy
X2
MEMOIRS Handle Assy
MEMOIRS Wall Clip Assy
X4
MEMOIRS Bottom Clip Assy
X2
MEMOIRS Wall Clip Body Cover
X4
Frame Cap LH
()X1
Frame Cap LH
()X1
Frame Cap RH
()X1
Frame Cap RH
()X1
Frame Cap
X1
Frame Cap
X1
Special Key
X1
Cover
X8
4mm Allen Key
4mm
X2
X2
X4
Hinge Cover
X20
SINGULIER Bracket Assy
X2
SINGULIER Handle Assy
SINGULIER Wall Clip Assy
X4
SINGULIER Bottom Clip Assy
X2
SINGULIER Wall Clip Body Cover
X4
Special Key
X1
Cover
X8
4mm Allen Key
4mm
X2
X2
X4
Hinge Cover
X20
K-36944T/K-36958T
H
B
A
MEMOIRS 180 DEG Hinge Assy
180 X4
SINGULIER 180 DEG Hinge Assy
180 X4
1172434-T01-B

-3-
STEP
1
Fix the gasket to the glass.
STEP
2
Affix the wall clip to the glass ,screws not locked.
Note: Please
insert the glass
in the correct
direction.
INSTALLATION
STEP
3
Fix the wall clip and the floor clip.
30
30
6mm
6mm
1172434-T01-B

STEP
5
STEP
4
Align the glass to level, and lock the wall clip and the
floor clip.
Complete the glass installation of the other side
following the same steps.
-4-
Affix the hinge to the hole on top of the glass,
screws not locked.
Be aware of the direction
of the hinge: The upper
part should be fixed to the
glass.
STEP
6
+1mm
Align the cam with tools to up the hinge to level, then
lock the screws.
Tips: there are two
holes on the surface
of the cam, the
bigger one and the
smaller one
separately mark the
highest and the
lowest point of the
cam.
STEP
7
1172434-T01-B

-5-
0mm
STEP
8
STEP
9
STEP
10
Take down the hinge platen.
STEP
11
Aim the door glass at the hole location and affix it to
the hinge, and install the hinge platen, crews not
locked.
Affix the hinge to the hole on the bottom of the glass,
screws not locked.
Be auare of the
direction of the hige:
The upper part should
be fixed to the glass.
Align the cam with tools to level the glass, then lock
the screws.
Tips: there are
two holes on
the surface of
the cam, the
bigger one and
the smaller one
separately mark
the highest and
the lowest point
of the cam.
1172434-T01-B

-6-
STEP
12
Fix the handle.
STEP
13
Install bottom frame channel and cap.
STEP
14
Fix the magnetic stripe and the gasket.
Be aware of the direction of the
magnetic stripe and the gasket.
Fixed Glass Active Glass
If the door opens unwell, please loosen the wall clip
and the floor clip slightly, adjust the glass until the
door closed completely, then lock the screws.
STEP
15
1172434-T01-B

-7-
Fix the tierod.
STEP
16
STEP
17
Fix the cover caps to the wall clips.
0mm
0mm
STEP
18
Fix the cover caps to the hinges.
1172434-T01-B

-8-
STEP
19
STEP
20
Fix the bottom of the glass and use the water-
resistant gel.
Do not use the enclosure for at least 24 hours.
24
24hrs
1172434-T01-B