Leviton 10A11-1 Mounting instructions

TWO-WAY AUDIO/VOICE ALARM MODULE
Cat. No. 10A11-1
Installation Instructions and User’s Guide
INSTALLATION ENGLISH
DI-021-OA103-00AAR2213
SPKR1 (SPEAKER #1 OUTPUT)
SPKR1 (SPEAKER #1 COMMON)
SPKR2 (SPEAKER #2 OUTPUT)
SPKR2 (SPEAKER #2 COMMON)
TWISTED PAIR
WITH SHIELD
TWISTED PAIR
TWISTED PAIR
8 OHM
SPEAKER
SPEAKER
8 OHM
MODEL 10A11-1, REV C
TWO-WAY AUDIO/VOICE ALARM MODULE
TWO-WIRE
ELECTRET
MICROPHONE
MICROPHONE
ELECTRET
TWO-WIRE
33A00-4 CONSOLE,
33A00-20 KEYPAD, OR
28A00-1, 28A00-2,
MIC2 (MICROPHONE #2 COMMON)
MIC1 (MICROPHONE #1 COMMON)
MIC2 (MICROPHONE #2 INPUT)
MIC1 (MICROPHONE #1 INPUT)
-
+
-
+
-
+
-
+
SPEAKERS / MICROPHONES
HI-FI
IN
PAGE
HI-FI
SOURCE 6
AUDIO IN
LINE OUT (LINE-LEVEL AUDIO OUTPUT)
PAGE OUT (PAGE OUTPUT)
PAGE OUT (PAGE OUTPUT)
Figure 1 - Speaker/Microphone Connections
MOUNTING
When mounting and connecting the Model 10A11-1, Rev C, power down the controller (AC and battery). Connecting the Model 10A11-1, Rev C board, while power is still applied
to the controller, can damage the board, the controller, or both.
Mount the Model 10A11-1, Rev C to the upper right side of the enclosure using the supplied adhesive-backed resealable fasteners.
When connecting to an OmniLT, route the cable to the connector on the top of the board marked "J1". Plug the Model 10A11-1, Rev C cable into "J1" on the controller.
The red wire should be to the left of the connector (red wire to Pin 1) - See Figure 2.
Make sure that the connector is aligned with the pins on "J1".
When connecting to an Omni II, OmniPro II, Lumina, or Lumina Pro, route the cable along the top of the enclosure to the connector on the left side marked "J2". Plug the Model
10A11-1, Rev C cable into "J2" on the controller. The red wire should be to the top of the connector - See Figure 3. Make sure that the connector is aligned with the pins on "J2".
DESCRIPTION
The Model 10A11-1, Rev C Two-Way Audio/Voice Alarm Module allows two-way communication with a central station after an alarm, paging and listening from an on-premises or
remote phone, annunciation of alarm and zone by voice, and voice messaging. The Model 10A11-1, Rev C also provides a line-level audio output that can be tied into an amplifier or
whole home audio system, and a page output that is activated whenever the Model 10A11-1, Rev C generates audio output.
FEATURES
•  Tw o independentaudioampliers
•  Tw o microphoneinputs
• Line-levelaudiooutput(3.5mmjack)
• Pageoutput(contactclosure)
• Automaticgaincontrol(AGC)fortalkandlisten
• Two-wayorlisten-onlyoperation
• ControlviastandardTouch-Tonephone
• ConnectstoLevitonSpeaker/MicrophoneModulesand/orOmniConsoles
andLuminaKeypadswithBuilt-inSpeaker/Microphone
• ConnectstoHi-FibyLevitonandotherwholehomeaudiodistributionsystems
for announcing voice messages and paging
INSTALLATION
Connect 8-ohm speaker(s) and two-wire electret microphone(s) to the Model 10A11-1, Rev C - See Figure 1.LevitonModel28A00-1(Surface)orModel28A00-2(Flush)Speaker/
MicrophoneModulesand/orModel33A00-4OmniConsolesandModel33A00-20LuminaKeypadswithBuilt-inSpeaker/Microphonecanbeused.NOTE: Do not mount speakers,
microphones, 28A00 modules, 33A00-4 consoles, or 33A00-20 keypads near any device that may produce noise (fans, air conditioning units, audio speakers, etc.).
Microphones:
Microphonesshouldbeconnectedwith24AWGorlarger,shieldedtwistedpairwire.Wirelengthshouldnotexceed100feet.Connectthecableshieldsandnegativewires
together at the Model 10A11-1, Rev C terminal block only. Do not connect the shield on the microphone end. Additional microphones can be connected to each input in parallel.
Speakers:
Speakersshouldbeconnectedwith18AWGorlarger,twistedpairwire.Forwirerunsthatexceed50feet,use16AWGwireorlarger.Wirelengthshouldnotexceed100feet.
Additional speakers can be connected to each output in series.
Line-Level Audio Output:
Apowerampliermaybeconnectedtotheline-levelaudiooutputusinga3.5mmpatchcable.ThisistypicallyusedtoannunciatetheaudiooutputfromtheModel10A11-1,
Rev C throughout a home when used with a whole home audio distribution system.
Page Output:
The page output provides a contact closure whenever the Model 10A11-1, Rev C generates audio. This is typically used to trigger the paging feature of a whole home audio
distribution system.
SPECIFICATIONS
DIMENSIONS: 5.5"x3.25"
OPERATINGVOLTAGE: 6to14VDC
OPERATINGCURRENT: 500mAmaximum
SPEAKERIMPEDANCE: 8Ω
AGCRANGE: -22dbmto+10dbm
REQUIREDMICROPHONETYPE: Condenserw/built-inpreamp
WARNINGS AND CAUTIONS
• Readandunderstandallinstructions.Followallwarningsandinstructionsmarkedontheproduct.
• Donotusethisproductnearwater-e.g.,nearatub,washbasin,kitchensinkorlaundrytub,ina
wet basement, or near a swimming pool.
• Neverpushobjectsofanykindintothisproductthroughopenings,astheymaytouchdangerous
voltages.
• SAVETHESEINSTRUCTIONS.
WARNINGS AND CAUTIONS
• Neverinstallcommunicationswiringorcomponentsduringalightningstorm.
• Neverinstallcommunicationscomponentsinwetlocationsunlessthe
components are designed specifically for use in wet locations.
• Nevertouchuninsulatedwiresorterminalsunlessthewiringhasbeen
disconnected at the network interface.
• Usecautionwheninstallingormodifyingcommunicationswiringor
components.
(10I11-1)
WEB VERSION

For Technical Assistance Call: 800-824-3005 - www.leviton.com © 2013 Leviton Mfg. Co., Inc.
FOR CANADA ONLY
Forwarrantyinformationand/orproductreturns,residentsofCanadashouldcontactLevitoninwritingatLeviton Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
CONTROLLER SETUP
When using a Model 10A11-1, Rev C for two-way communication
with a central station, the Two-Way Voice option must be enabled.
FromtheInstallerSetupmenu,
select the 3 (DCM) key. Press the down arrow ( ) key until you
reachtheTwo-WayAudiooption:
TWO-WAY AUDIO: 0
0=NO 1=YES 
Press1(YES),andthenpress'#'toenabletwo-wayaudio
communication.
When using a Model 10A11-1, Rev C to announce alarms, the
Announce Alarms option must be enabled. To enable this option,
fromtheSetupmenupressthe6(MISC)key.
Press the down arrow ( ) key to until you reach the Announce
Alarmsoption:
ANNOUNCE ALARMS: 0
0=NO 1=YES 
Press1(YES),andthenpress'#'toenablethesystemannouncealarms.
OPERATION
The Two-Way Audio Module has two modes of audio communication:
1. Listen modeisusedtolistentothepremisesfromaninside,remote,orcentralstationtelephone.Yo u cannottalktoanyoneonpremisesinlistenmode.Wheneverthemodule
is switched on, it is set to the listen mode.
2. Talk modeisusedtotalktosomeoneon-premisesfromaninside,remote,orcentralstationtelephone.Yo u cannotlistentothepremiseswhileinthetalkmode.Themode
can be changed between listen and talk by using the keys on a phone. When the module is switched on, a 90 second disconnect timer is started. If no tones are detected
within 90 seconds, the module will be switched off. Each time a tone is received, the timer is reset.
CENTRAL STATION OPERATION
When an alarm occurs, the communicator first sends the appropriate report to the central station. After the transmission of the alarm to the central station, the operator can talk
and listen to people and sounds at the premises. After the report is received by the central station operator, the Two-Way Audio Module is switched on. The central station operator
can now listen to the premises. The module is always first switched on in the listen mode. The operator can control the direction of the communication by using the Touch-Tones
onatelephone.Eachtimetheoperatorswitchesbetweenthelistenandthetalkmode,ashorttonewillsoundovertheaudiospeakeratthesubscriber'spremises.Thisalertsthe
subscriber that the operator has switched communication mode. If no tones are detected within 90 seconds, the module will disconnect from the phone line.
PRESS 2 FOR CENTRAL STATION TO TALK TO THE PREMISES
PRESS 8 FOR CENTRAL STATION TO LISTEN TO THE PREMISES
PRESS 4 TO DISCONNECT (HANG UP) THE PHONE LINE
When the Two-Way Audio Module is switched on after an alarm transmission, the siren is automatically switched off so the central station can listen and talk to the premises.
PAGING AND LISTENING
By accessing the telephone menu, you can use an inside or remote phone to talk (page) and listen to someone on the premises.
1) From the main telephone menu choose the 8 (PHONE).
2) To talk or listen to the premises, press the 3 (INTERIOR).
3) To talk to someone at the premises, press the 2 key.
4) To listen to the premises, press the 8 key.
• Ifnokeyispressed,thesystemwillautomaticallyswitchtolistenmode.
• Whencomplete,press*toreturntothemaintelephonemenu.
• Ifnotonesaredetectedwithin90seconds,themodulewillswitchoffandyouwillreturntothemaintelephonemenu.
ANNUNCIATION OF ALARM
The Voice Alarm Module enables the system to speak the type of alarm and zone over a speaker on premises. When an alarm first occurs, the siren is activated. After a few
seconds, the siren is turned off and the type of alarm is announced. The siren is then reactivated. After a few seconds, the siren is again turned off and the violated zone is
announced. The siren is then reactivated. This process is repeated until the alarm is disarmed or reset.
NOTE: During central station communication (while the system is reporting an alarm to the central station), voice alarm notifications are temporarily suspended. After the
successful transmission of the alarm to the central station, voice alarm notifications are restarted.
SPEAKER VOLUME CONTROL
Thevolumeoftheaudiocanbecontrolledbyadjustingavariableresistoronthemodule.UseasmallscrewdrivertoadjustR35labeled"SpeakerVolume".
Do notadjustR59labeled"AudioCancel".Thisvariableresistoritisadjustedatthefactorytoitsoptimalsetting.
DI-021-OA103-00AAR2213
FCC Compliance
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
usedinaccordancewiththeinstructions,maycauseharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterferencewillnotoccurinaparticular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
totrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
LEVITON LIMITED WARRANTY
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that products manufactured by Leviton under the Leviton brand name (“Product”) will be free from
defects in material and workmanship for the time periods indicated below, whichever is shorter: • OmniPro II and Lumina Pro: three (3) years from installation or 42 months from manufacture date.
• OmniLT, Omni IIe, and Lumina: two (2) years from installation or 30 months from manufacture date. • Thermostats, Accessories: two (2) years from installation or 30 months from manufacture date.
• Batteries: Rechargeable batteries in products are warranted for ninety (90) days from date of purchase. Note: Primary (non-rechargeable) batteries shipped in products are not warranted.
Products with Windows®Operating Systems: During the warranty period, Leviton will restore corrupted operating systems to factory default at no charge, provided that the product has been used as
originally intended. Installation of non-Leviton software or modification of the operating system voids this warranty. Leviton’s obligation under this Limited Warranty is limited to the repair or replacement,
at Leviton’s option, of Product that fails due to defect in material or workmanship. Leviton reserves the right to replace product under this Limited Warranty with new or remanufactured product.
Leviton will not be responsible for labor costs of removal or reinstallation of Product. The repaired or replaced product is then warranted under the terms of this Limited Warranty for the remainder
of the Limited Warranty time period or ninety (90) days, whichever is longer. This Limited Warranty does not cover PC-based software products. Leviton is not responsible for conditions or applications
beyond Leviton’s control. Leviton is not responsible for issues related to improper installation, including failure to follow written Installation and operation instructions, normal wear and
tear, catastrophe, fault or negligence of the user or other problems external to the Product. To view complete warranty and instructions for returning product, please visit us at www.leviton.com.
Usehereinofthirdpartytrademarks,servicemarks,tradenames,brandnamesand/orproductnamesareforinformationalpurposesonly,are/maybethetrademarksoftheir
respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
WEB VERSION