Liko Likorall 200 User manual

Product Descripon
In this document, the person being lied is referred to as the paent, and the person helping them is referred to as the
caregiver.
Likorall overhead li is a staonary li unit oen called an
“overhead li”. Likorall overhead li is mounted in LikoTM
rail system, which is adapted to suit the room/rooms it
will be operated in. The rail system can be built straight,
with or without curves, as a traverse system and also as a
room-to-room system. LikoTM rail system is comprised of
several hundred dierent components, we select the specic
components needed to customize each system to suit the
room it will be mounted in. The rail system can either be xed
or freestanding, such as Liko FreeSpan and Liko FreeStand.
The system must be installed by authorized personnel and in
accordance with LikoTM installaon instrucons.
Likorall overhead li is intended for use in liing and transferring
paents, for example, from bed to a wheelchair, to or from
the oor, for visits to the toilet, for gait, standing and balance
training, when weighing the paent and when liing the
paent with a stretcher.
Likorall 200 overhead li is adapted to the LikoTM Quick-release
Hook System for safe and easy changing of liing accessories.
The LikoTM Room-to-Room system (R2R), enables the paent
to be moved between two rail systems in separate rooms,
without connecng rails and without making holes over doors.
A large range of accessories are available for Likorall overhead
li, including dierent sling models in a range of types and sizes.
Likorall™ 200
overhead li
Instrucons for Use
Likorall 200 overhead li Product No. 3121001
7EN120114 Rev. 10
ENGLISH 2020
IMPORTANT!
Liing and transferring a paent always involves a certain level of risk. Read the instrucons for use for both the paent
li and liing accessories before use. It is important to completely understand the contents of the instrucons for use.
The equipment should only be used by trained personnel. Ensure that the liing accessories are suitable for the li used.
Exercise care and cauon during use. As a caregiver, you are always responsible for the paent’s safety. You must be aware of
the paent’s ability to make it through the liing situaon. If something is unclear, contact the manufacturer or supplier.

2www.hillrom.com
7EN120114 Rev. 10 • 2020
Table of Contents
Symbol Descripon .......................................................................................................................... 3
Safety Instrucons ........................................................................................................................... 4
Denions ....................................................................................................................................... 5
Technical Data ................................................................................................................................. 5
Measurements ................................................................................................................................. 6
EMC Table ......................................................................................................................................... 6
Assembly .......................................................................................................................................... 9
Operaon ......................................................................................................................................... 9
Charging the Baeries .................................................................................................................. 12
Transferring from Room to Room ................................................................................................... 13
Maximum Load ............................................................................................................................... 14
Recommended Liing Accessories ................................................................................................. 14
Simple Troubleshoong .................................................................................................................. 16
Recycling Instrucons ..................................................................................................................... 17
Cleaning and Disinfecon .............................................................................................................. 18
Inspecon and Maintenance ......................................................................................................... 22

3www.hillrom.com
7EN120114 Rev. 10 • 2020
These symbols can be found in this document and/or on the product.
Symbol Descripon
For indoor use only.
The product has extra protecon against electric shock (Insulaon Class II).
Protecon level against electric shock Type B.
Warning. Used were extra care and aenon is needed.
Read instrucon for use before use.
This product complies with EC direcves.
IP N1 N 2 Protecon level against: ingress of solid objects (N1) and ingress of water (N2).
Manufacturer.
Date of manufacture.
Cauon! consult instrucons for use.
Baery.
,
Pb
,
All baeries in this product must be recycled separately.
- Pb underneath the symbol indicate baeries containing lead
- Single Black line underneath the symbol indicate this product have been placed on the market aer 2005.
UL Recognized Component Mark for Canada and the United States.
EFUP, Environmental Friendly Usage Period (years).
Environmentally-friendly product which can be recycled and reused.
The Australian Safety/EMC.
PSE Mark (Japan).
Product Idener.
Serial Number.
Medical Device.
Recyclable.
The safety and essenal performance of medical electrical equipment.
Proof of Product compliance to North American safety standards.
Non-ionizing electromagnec radiaon.
X%
Y% ≤Tmin
Duty cycle for non-connuous operaon.
The maximum acve operaon me X% of any given me unit, followed by a deacvaon me, Y%.
The acve operaon me shall not exceed the specied me in minutes, T.
(01) 0100887761997127
(11) Y Y MM D D
(21) 012345678910
GS1 Data Matrix Barcode that may contain following informaon
(01) Global Trade Item Number
(11) Producon Date
(21) Serial Number
Symbol Descripon

4www.hillrom.com
7EN120114 Rev. 10 • 2020
Safety Instrucons
Before liing always ensure that:
• the li strap is not twisted or worn and can move in and out of the li unit freely
• the liing accessories are not damaged
• the sling is correctly and securely applied to the paent in order to prevent injuries from occurring
• the liing accessory is correctly applied to the li
• the liing accessories hang vercally and can move freely
• the sling bar latches are intact; missing or damaged latches must always be replaced
• the sling strap loops are correctly connected to the sling bar hooks when the sling´s strap is extended upward, but before
the paent is lied from the underlying surface.
Incorrect aachment of sling to slingbar may cause severe injury to the paent.
If the Likorall is installed in the S65 carriage with single hook, make sure it is resng securely at the boom of the hook
and is not lted.
Never leave a paent unaended during a liing situaon!
Only use the LikorallTM overhead li with a carriage, adapter, sling bar and other accessories approved by Hill-Rom.
Before using the li the rst me make sure that:
• the li is assembled in accordance with the assembly instrucon
• the liing accessories are properly aached to the li
•the baeries are charged for at least 8 hours
• you have read the instrucons for use for the li and liing accessories
• personnel using the li are informed of the correct use of the li and liing accessories
• the liing accessory is selected appropriately, in terms of type, size, material and design with regard to the paent’s needs.
No modicaon of this product is allowed.
Portable RF communicaons equipment (including peripherals such as antenna cables and external antennas) should be
used no closer than 30 cm (12 inches) to any part of the li, including cables specied by the manufacturer. Otherwise,
degradaon of the performance of this equipment could result.
Use of the product adjacent to other equipment should be avoided because it could result in improper operaon, if such use
is necessary, observe and verify that the other equipment is operang normally.
Electromagnec disturbance, may aect the liing performance of the product. Modicaon using other parts than original
spare parts (cables etc.) may aect the electromagnec compability of the product.
Parcular care must be observed when using strong sources of electromagnec disturbance, such as diathermy, etc, so that dia-
thermy cables are not posioned on or near the li. If you have quesons, please consult the responsible assisve-device technician
or the supplier.
The li may not be used in areas where ammable mixtures may occur, for example in areas where ammable goods are stored.
Installaon of Likorall overhead li to carriages shall be made by personnel authorized by LikoTM in accordance with the
installaon instrucons and recommendaons for the current li system.
Intended use: The product is intended for use in following environments: Health care, Intensive care, Emergency ward,
Rehabilitaon, Habilitaon environment. This product is not intended to be used by the paent alone. Liing and transferring a
paent shall always be performed with the assistance of at least one caregiver. This product is used as a means to perform the li
but is not in contact with the paent; therefore we do not go into the various paent condions in this instrucon for use. Contact
your Hill-Rom representave for support and advice.
Likorall 200 is tested by an accredited tesng instute.

5www.hillrom.com
7EN120114 Rev. 10 • 2020
Technical Data
Maximum load: 200 kg (440 Ibs.)
Baeries: 2 x 12V 2,4-2,6 Ah.
Valve-regulated lead-acid gel-
type baeries. New baeries are
provided by the supplier.
Baery charger: CH01 FW7218M/24; 100-240 V AC,
50-60 Hz, max 500 mA
Liing speed: 50 mm/s (2 inch./s)
Liing interval: 2050 mm (80.7 inch.)
Electrical data: 24 V, 12 A
Li unit dimensions: 340x250x165 mm (LxWxH)
(13.4x9.8x6.5 inch. ,LxWxH)
Li unit weight: 12.5 kg (27.5 lbs.)
Emergency lowering
device: Electrical
Likorall overhead li is equipped with a SFS (Single Fault Safety) safety drum. This patented safety design provides protecon
against uncontrolled lowering.
Intermient power:
Protecon class li
motor:
Sound level:
Protecon class
hand control:
Operang forces
hand control:
Int. Op 10/90, acve operaon max
30 sec.
IP 33
51 dB
IP 54
3 N
Cable length
hand control: 870 mm (34 inch.)
Intended for indoor use.
Type B, in accordance with the electrical shock
protecon class.
Denions
1. Hand control with spring clamp
2. Emergency lowering device (electric)
3. Emergency stop string
4. Emergency stop
5. End cover
6. Charge indicator
7. Li unit
8. SSP Limit Switch
9. Li strap
10. Q-Link II (quick fastener)
11. Quick-release hook
12. Sling bar
13. Latches
14. Q-Link (quick fastener)
3
6
1
8
5
2
7
10
9
11
13
12
4
14

6www.hillrom.com
7EN120114 Rev. 10 • 2020
CSP (Central Suspension Point)
C
A
B
H** D*
L***
Measurements
* Minimum distance from ceiling to CSP at maximum liing height with the standard carriage.
** Built-in dimension: the distance between the aachment point for the li unit on the carriage and the CSP at maximum
liing height.
*** Liing interval: the distance between maximum liing height and minimum liing height measured in CSP.
Measurements in mm.
Measurements in inch.
ABCD* H** L***
165 340 250 304 221 2050
ABCD* H** L***
6.5 13.4 9.8 12.0 8.7 80.7
Overhead view
Lateral view
Guidance and manufacturer’s declaraon – electromagnec emissions
The product is intended for use in the electromagnec environment specied below. The customer or the user of this
product should assure that it is used in such an environment.
Emissions test Compliance Electromagnec environment - guidance
RF emissions
CISPR 11
Group 1 The product uses RF energy only for its internal
fuon. Therefore, its RF emissions are very low and
are not likely to cause any interference in nearby
electronic equipment.
RF emissions
CISPR 11
Class B
The product is suitable for use in all establishments
other than domesc and those directly connected
to the public low-voltage power supply network
that supplies buildings used for domesc purposes.
Harmonic emissions
IEC 61000-3-2
Class A
Voltage uctuaons/ icker emissions
IEC 61000-3-3
Complies
EMC Table
Ceiling

7www.hillrom.com
7EN120114 Rev. 10 • 2020
Guidance and manufacturer’s declaraon – electromagnec immunity
The product is intended for use in the electromagnec environment specied below. The customer or the user of this
product should assure that it is used in such an environment.
Immunity test IEC 60601 test level Compliance level Electromagnec environment - guidance
Electrostac discharge
(ESD)
IEC 61000-4-2
+/- 6 kV contact
+/- 8 kV air
+/- 6 kV contact
+/- 8 kV air
Electrical fast transient
/ Burst
IEC 61000-4-4
+/- 2 kV for power supply
lines
+/- 1 kV for input/output
lines
+/- 2 kV for power supply
lines
n/a. for input/output lines
Mains power quality should be that of a typi-
cal commercial or hospital environment.
Surge
IEC 61000-4-5
+/- 1 kV dierenal mode
+/- 2 kV common mode
+/- 1 kV dierenal mode
n/a. for common mode
Mains power quality should be that of a typi-
cal commercial or hospital environment.
Voltage dips, short
interrupons and
voltage variaons on
power supply input
lines
IEC 61000-4-11
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
<5 % UT
(>95 % dip in UT))
for 5 sec
Power frequency
(50/60 Hz) magnec
eld
IEC 61000-4-8
3 A/m 3 A/m Power frequency magnec elds should be
at levels characterisc of a typical locaon in
a typical commercial or hospital environment
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to 80 MHz
3 Vrms
150 kHz to 80 MHz
Radiated RF
IEC 61000-4-3
10 V/m
80MHz to 2,5GHz
10 V/m
80MHz to 2,5GHz
NOTE UT is the a.c. mains voltage prior to applicaon of the test level.

8www.hillrom.com
7EN120114 Rev. 10 • 2020
Guidance and manufacturer’s declaraon – electromagnec immunity
The product is intended for use in the electromagnec environment specied below. The customer or the user of this
product should assure that it is used in such an environment.
Immunity test IEC 60601 test level Compliance
level
Electromagnec environment - guidance
Portable and mobile RF communicaons equipment should
be used no closer to any part of the product, including cables,
than the recommended separaon distance calculated from the
equaon applicable to the frequency of the transmier.
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to 80 MHz
Recommended separaon distance
d P=035,
Radiated RF
IEC 61000-4-3
10 V/m
80MHz to 2,5GHz
d P=029,
80 MHz to 800 MHz
d P=058,
800 MHz to 2,5 GHz
where P is the maximum output power rang of the transmier
in was (W) according to the transmier manufacturer and d is
the recommended separaon distance in meters (m).
Field strengths from xed RF transmiers, as determined by an
electromagnec site survey, a should be less than the compli-
ance level in each frequency range. b
Interference may occur in the vicinity of equipment marked with
the following symbol.
NOTE 1 At 80MHz and 800MHz, the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situaons. Electromagnec propagaon is aected by absorpon and reected
from structures, objects and people.
a Field strengths from xed transmiers, such as base staons for radio (cellular/cordless) telephones and land mobile radios,
amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theorecally with accuracy. To assess the
electromagnec environment due to xed RF transmiers, an electromagnec site survey should be considered. If the mea-
sured eld strength in the locaon in which the product is used exceeds the applicable RF compliance level above, the product
should be observed to verify normal operaon. If abnormal performance is observed, addional measures may be necessary,
such as reorienng or relocang the product.
b Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 10 V/m.

9www.hillrom.com
7EN120114 Rev. 10 • 2020
Assembly
• the SSP Limit Switch funcons properly
• the baery charger funcons properly and the
indicator lamps are illuminated during charging
• the baeries are charged for at least 8 hours before the
li is used for the rst me.
Aer assembly, ensure that:
• the li’s funcons correspond to the markings of the
hand control
• the electrical emergency lowering device
funcons properly
Liing accessory with quick-release hook,
Push down the red catch and connect the quick-release hook to the Q-Link II or Q-Link. Release
and check that the catch locks in order to prevent involuntary unhooking from the Q-Link II
or Q-Link. Read more about the Liko
TM
Quick-release Hook system on page 15.
Before liing check that the
Quick-release Hook is correctly
aached to the Q-Link II or
Q-Link, see illustraon above.
Quick
Release Hook
Q-Link II
or Q-Link
Manoeuvring
The liing moon in LikorallTM 200 overhead li is controlled
using an aached hand control. LikorallTM 200 overhead li
is manoeuvered by pressing lightly on the hand control
buons. The arrows indicate direcon. Moon ceases when
the buon is released.
Operaon
Up
Down
Hand control with spring clamp
When the li is not in use, the hand control can be aached
to the li strap using the spring clamp on the back side of
the hand control.

10 www.hillrom.com
7EN120114 Rev. 10 • 2020
Electrical Emergency lowering
In the event that the hand control or electronics
malfuncon, the li can be lowered by pulling on
the emergency lowering device.
In the event of emergency lowering, always ensure the
paent is lowered into a bed, wheelchair or other suitable
place.
Emergency stop
To acvate the emergency stop: pull the red emergency
stop string.
To reset the emergency stop: turn the red emergency stop
buon in the direcon shown by the arrows.
The red buon on the li unit end cover is intended
for use if an emergency situaon occurs. When the buon
is pressed, contact between the motor and power source is
broken, which stops the liing moon.
Installaon of Latches
Aer installaon, check that the
latch locks and runs freely in the
sling bar hook.
Li correctly!
Before each li, make sure that:
– the Sling loops at opposite sides of the Sling are at the same height
– all the Sling loops are fastened securely in to the Slingbar hooks
– the Slingbar is level during the li, see Figure 1.
If Slingbar is not level (see Figure 2) or if the sling loops are incorrectly at-
tached to the slingbar (see Figure 3) lower the user to a rm surface and ad-
just according to the Instrucons for use of Sling in use.
An improper li can be uncomfortable for the user and cause damage to
the li equipment! (see Figure 2 and gure 3).
Figure 1. Figure 2. Figure 3.