MASSEY FERGUSON MF 9283 User manual

MF 9283 / 9286
SERVICE MANUAL
Rotary Disc Header
FROM MASSEY FERGUSON

Find manuals at https://best-manuals.com

Workshop Service Manual
Rotary Disc Header
9283
9286
North America
4205 River Green Parkway, Duluth GA 30096 USA
© AGCO 2017
November 2017
4283612M1
NA
English
Find manuals at https://best-manuals.com

CALIFORNIA
Proposition 65 Warning
WARNING: Diesel engine exhaust and some of its constituents are known to the State of
California to cause cancer, birth defects, or other reproductive harm.
WARNING: Battery posts, terminals and related accessories contain lead and lead compounds,
chemicals known to the State of California to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling.
Find manuals at https://best-manuals.com

Rotary Disc Header
1 General ..................................................................1-1
1.1 General information ................................................1-3
1.1.1 Introduction to this service manual ....................................1-3
1.1.2 Units of measurement .............................................1-3
1.1.3 Table of contents ................................................1-3
1.1.4 Page numbers .................................................. 1-3
1.1.5 Intended use ................................................... 1-3
1.1.6 Proper disposal of waste ...........................................1-3
1.2 General safety .....................................................1-5
1.2.1 Safety symbol ...................................................1-5
1.2.2 Safety messages ................................................ 1-5
1.2.3 Information messages .............................................1-5
1.2.4 Safety signs ....................................................1-5
1.2.5 Safety and informational signs .......................................1-6
1.2.6 Accumulator safety ...............................................1-8
1.2.7 A word to the technician ...........................................1-8
1.2.8 The service manual ...............................................1-9
1.3 Operation ........................................................1-10
1.3.1 Prepare for operation .............................................1-10
1.3.2 General information ..............................................1-10
1.3.3 Personal protective equipment ......................................1-11
1.3.4 Seat instructions ................................................1-11
1.3.5 Shield and guards ...............................................1-12
1.3.6 Exhaust warning ................................................1-12
1.3.7 Flying debris ...................................................1-13
1.3.8 Handrails .....................................................1-13
1.3.9 Agricultural chemicals ............................................1-13
1.3.10 Travel on public roads ...........................................1-14
1.4 Maintenance ......................................................1-15
1.4.1 General maintenance information ....................................1-15
1.4.2 Bolt torque values ...............................................1-16
1.4.3 Fire prevention and first aid ........................................1-19
1.4.4 High pressure leaks ..............................................1-20
1.4.5 Tire safety .....................................................1-20
1.4.6 Replacement parts ..............................................1-21
1.4.7 Remove an eccentric locking collar ...................................1-21
1.4.8 Install an eccentric locking collar ....................................1-21
1.4.9 Remove a gib key ...............................................1-22
1.4.10 Install a gib key ................................................1-23
1.5 Specifications .....................................................1-24
1.5.1 Maximum roading speed ..........................................1-24
1.5.2 Dimensions and weights ..........................................1-24
1.5.3 Header specifications ............................................1-24
1.5.4 Cutterbed specifications ..........................................1-24
1.5.5 Cutterbed bolt torque ............................................1-25
1.5.6 Conditioner specifications .........................................1-25
1.5.7 Lubrication specifications ..........................................1-25
1.6 Machine identification .............................................1-27
1.6.1 Machine identification ............................................1-27
1.6.2 Serial number plate ..............................................1-27
1.6.3 Serial number description .........................................1-27
Table of contents
Rotary Disc Header
4283612M1
Find manuals at https://best-manuals.com

1.7 Machine description ...............................................1-29
1.7.1 Description ....................................................1-29
1.7.2 Cutterbed .....................................................1-29
1.7.3 Conditioner ....................................................1-29
1.7.4 Swathboard ...................................................1-30
1.7.5 Forming shields .................................................1-30
1.8 Component location ..............................................1-31
1.8.1 Component location .............................................1-31
1.8.2 Component access ..............................................1-31
1.9 Troubleshooting ..................................................1-32
1.9.1 Header troubleshooting ...........................................1-32
1.9.2 Cutterbed troubleshooting .........................................1-33
1.9.3 Conditioner troubleshooting ........................................1-34
1.9.4 Crop conditioning and windrow formation ..............................1-35
1.9.5 Cutoff quality ..................................................1-35
2 Drive system .............................................................2-1
2.1 Conditioner drive belt ..............................................2-3
2.1.1 Banded drive belt ................................................2-3
2.1.2 Install a belt ....................................................2-3
2.1.3 Belt run-in procedure ..............................................2-4
2.2 Helper roll drive belt ............................................... 2-6
2.2.1 Replace the helper roll drive belt .....................................2-6
2.2.2 Adjust the helper roll drive belt .......................................2-6
2.3 Header drive gearbox .............................................. 2-7
2.3.1 Header drive gearbox components ....................................2-7
2.3.2 Special tools (header drive gearbox) ...................................2-8
2.3.3 Remove the header drive gearbox ....................................2-8
2.3.4 Disassemble the header drive gearbox ................................2-10
2.3.5 Examine the header drive gearbox ...................................2-16
2.3.6 Assemble the header drive gearbox ..................................2-17
2.3.7 Install the header drive gearbox .....................................2-21
2.3.8 Adjust the header drive gearbox .....................................2-23
2.4 Conditioner drive tensioner ........................................2-25
2.4.1 Header drive tensioner components ..................................2-25
2.4.2 Disassemble the header drive tensioner ...............................2-26
2.4.3 Examine the conditioner drive tensioner ...............................2-26
2.4.4 Assemble the conditioner drive tensioner ..............................2-27
3 Hydraulic system .........................................................3-1
3.1 General information ................................................3-3
3.1.1 General hydraulic information ........................................3-3
3.1.1.1 Hydraulic system ..........................................3-3
3.2 Header drive motor ................................................3-4
3.2.1 Header drive motor components .....................................3-4
3.2.2 Examine the case drain leakage ......................................3-5
3.2.3 Remove the header drive motor ......................................3-7
3.2.4 Disassemble the header drive motor ..................................3-9
3.2.5 Assemble the header drive motor ...................................3-16
3.2.6 Install the header drive motor .......................................3-25
3.3 Conditioner drive motor (double conditioner) .......................3-29
3.3.1 Remove the conditioner drive motor (double conditioner) ..................3-29
3.3.2 Install the conditioner drive motor (double conditioner) ....................3-29
3.4 Conditioner roll cylinders ..........................................3-30
3.4.1 Conditioner roll cylinder components .................................3-30
3.4.2 Remove the conditioner roll cylinders ................................3-30
Table of contents
Rotary Disc Header
4283612M1
Find manuals at https://best-manuals.com

3.4.3 Disassemble the conditioner roll cylinder ..............................3-31
3.4.4 Examine the conditioner roll cylinder .................................3-31
3.4.5 Assemble the conditioner roll cylinder ................................3-32
3.4.6 Install the conditioner roll cylinder ...................................3-32
3.4.7 Adjust the pressure of the conditioner roll cylinders ......................3-33
3.5 Accumulator ......................................................3-34
3.5.1 General information ..............................................3-34
3.5.2 Remove the accumulator ..........................................3-34
3.5.3 Discharge the accumulator ........................................3-34
3.5.4 Charge the accumulator ...........................................3-35
3.5.5 Install the accumulator ............................................3-35
4 Electrical system ......................................................... 4-1
4.1 Basic electrical troubleshooting .....................................4-3
4.1.1 Basic troubleshooting procedures ....................................4-3
4.1.2 Tools .........................................................4-4
4.1.3 Continuity check .................................................4-4
4.1.4 Voltage check ...................................................4-5
4.2 Connectors ........................................................4-6
4.2.1 Examine a connector ..............................................4-6
4.2.2 Terminal numbers ................................................4-6
4.2.3 Pins and sockets .................................................4-7
4.2.4 Replace a Packard connector ........................................4-8
4.2.5 Replace an AMP connector .........................................4-8
4.2.6 Replace a Power Cord connector .....................................4-8
4.2.7 Replace a Deutsch connector ....................................... 4-9
4.3 Header speed sensor ..............................................4-11
4.3.1 Electrical sensor location ..........................................4-11
4.3.2 Adjust the electrical sensors .......................................4-11
5 Cutterbed ................................................................5-1
5.1 Discs ..............................................................5-3
5.1.1 Discs .........................................................5-3
5.1.2 Disc maintenance ................................................5-3
5.1.3 Remove an inner disc .............................................5-3
5.1.4 Install an inner disc ...............................................5-4
5.1.5 Remove the outer disc ............................................5-5
5.1.6 Install the outer disc ..............................................5-7
5.2 Knives .............................................................5-9
5.2.1 Knife wedging under disc ..........................................5-9
5.2.2 Knife inspection .................................................5-9
5.2.3 Replace a knife .................................................5-10
5.2.4 Knife hardware inspection .........................................5-10
5.3 Cutterbed ........................................................5-12
5.3.1 Cutterbed .....................................................5-12
5.3.2 Cutterbed oil level ...............................................5-12
5.3.3 Change the cutterbed oil ..........................................5-12
5.3.4 Lubrication specifications ..........................................5-14
5.3.5 Cutterbed inspection .............................................5-15
5.3.6 Cutterbed components ...........................................5-16
5.3.7 Remove the cutterbed ............................................5-16
5.3.8 Disassemble the cutterbed ........................................5-19
5.3.9 Examine the cutterbed ...........................................5-20
5.3.10 Assemble the cutterbed .........................................5-21
5.3.11 Examine the cutterbed for leaks ....................................5-23
5.3.12 Install the cutterbed .............................................5-24
5.4 Spindle gear assembly ............................................5-27
Table of contents
Rotary Disc Header
4283612M1
Find manuals at https://best-manuals.com

5.4.1 Spindle gear assembly ............................................5-27
5.4.2 Remove the spindle gear ..........................................5-27
5.4.3 Disassemble the spindle gear ......................................5-28
5.4.4 Examine the spindle gear ..........................................5-28
5.4.5 Assemble the spindle gear .........................................5-29
5.4.6 Install the spindle gear ............................................5-30
5.5 Idler gear assembly ...............................................5-32
5.5.1 Idler gear assembly ..............................................5-32
5.5.2 Remove the idler gear ............................................5-32
5.5.3 Disassemble the idler gear .........................................5-34
5.5.4 Examine the idler gear ............................................5-35
5.5.5 Assemble the idler gear ...........................................5-35
5.5.6 Install the idler gear ..............................................5-36
6 Conditioner ..............................................................6-1
6.1 Helper roll .........................................................6-3
6.1.1 Helper roll components ............................................6-3
6.1.2 Remove the helper roll ............................................6-3
6.1.3 Install the helper roll ..............................................6-8
6.2 Drive shaft ........................................................6-15
6.2.1 Remove the drive shaft - slip tube ...................................6-15
6.2.2 Install the drive shaft - slip tube .....................................6-16
6.2.3 Remove the drive shaft - solid shaft ..................................6-18
6.2.4 Install the drive shaft - solid shaft ....................................6-18
6.3 U-joint ...........................................................6-20
6.3.1 U-joint components ..............................................6-20
6.3.2 Remove the U-joints .............................................6-20
6.3.3 Disassemble the U-joint ...........................................6-21
6.3.4 Assemble the U-joint .............................................6-23
6.3.5 Install the U-joints ...............................................6-29
6.4 Belts .............................................................6-31
6.4.1 Belt maintenance ...............................................6-31
6.4.2 Replace the conditioner belt ........................................6-31
6.4.3 Adjust the conditioner belt .........................................6-32
6.4.4 Replace the helper roll belt ........................................6-33
6.4.5 Adjust the helper roll belt ..........................................6-33
6.5 Left conditioner gearbox ..........................................6-34
6.5.1 Conditioner gearbox lubrication .....................................6-34
6.5.2 Remove the left conditioner gearbox .................................6-34
6.5.3 Conditioner gearbox components - left ................................6-35
6.5.4 Disassemble the left conditioner gearbox ..............................6-36
6.5.5 Examine the conditioner gearbox ....................................6-36
6.5.6 Assemble the left conditioner gearbox ................................6-37
6.5.7 Install the left conditioner gearbox ...................................6-38
6.6 Right conditioner gearbox - double conditioner only .................6-40
6.6.1 Conditioner gearbox lubrication .....................................6-40
6.6.2 Remove the right conditioner gearbox ................................6-40
6.6.3 Conditioner gearbox components - right ...............................6-41
6.6.4 Disassemble the right conditioner gearbox .............................6-42
6.6.5 Examine the conditioner gearbox ....................................6-42
6.6.6 Assemble the right conditioner gearbox ...............................6-43
6.6.7 Install the right conditioner gearbox ..................................6-44
6.7 Conditioner bearings ..............................................6-46
6.7.1 Remove a spherical bearing ........................................6-46
6.7.2 Install a spherical bearing ..........................................6-47
6.7.3 Remove a bushing bearing .........................................6-48
6.7.4 Install a bushing bearing ..........................................6-48
Table of contents
Rotary Disc Header
4283612M1
Find manuals at https://best-manuals.com

6.8 Rear conditioner - double conditioner only ..........................6-50
6.8.1 Rear top conditioner - components (double conditioner) ....................6-50
6.8.2 Remove the rear top conditioner - double conditioner .....................6-51
6.8.3 Install the rear top conditioner roll - double conditioner ....................6-52
6.8.4 Rear bottom conditioner components - double conditioner .................6-55
6.8.5 Remove the rear bottom conditioner - double conditioner ..................6-55
6.8.6 Install the rear bottom conditioner - double conditioner ....................6-57
6.9 Front conditioner .................................................6-60
6.9.1 Front top conditioner - components ..................................6-60
6.9.2 Remove the front top conditioner ....................................6-61
6.9.3 Install the front top conditioner .....................................6-62
6.9.4 Front bottom conditioner - components ...............................6-63
6.9.5 Remove the front bottom conditioner .................................6-63
6.9.6 Install the front bottom conditioner ...................................6-66
6.10 Conditioner adjustments .........................................6-71
6.10.1 Examine the conditioner .........................................6-71
6.10.2 Conditioner ...................................................6-71
6.10.3 Conditioner spacing .............................................6-71
6.10.3.1 Adjust the conditioner roll spacing ............................6-71
6.10.4 Conditioner spacing indicator ......................................6-72
6.10.4.1 Adjust the conditioner spacing indicator - double conditioner .........6-72
6.10.4.2 Adjust the conditioner spacing indicator - single conditioner .........6-73
6.10.5 Adjust the conditioner timing ......................................6-73
6.10.6 Conditioner pressure ............................................6-74
6.10.7 Adjust the conditioner pressure ....................................6-74
6.11 Windrow forming shields .........................................6-75
6.11.1 Adjust the windrow forming shields .................................6-75
6.11.2 Adjust the deflector .............................................6-75
6.11.3 Adjust the windrow forming deck height ..............................6-75
6.12 Swathboard .....................................................6-77
6.12.1 Swathboard ..................................................6-77
6.12.2 Adjust the swathboard ...........................................6-77
7 Diagrams ................................................................ 7-1
7.1 Reading wiring diagrams ...........................................7-3
7.1.1 Diagram numbers ................................................7-3
7.1.2 Location grids ...................................................7-3
7.1.3 Wire breaks ....................................................7-4
7.2 Diagram symbols and abbreviations .................................7-6
7.2.1 Harness and connector identification ..................................7-6
7.2.2 Splices ........................................................7-6
7.2.3 CAN signal .....................................................7-7
7.3 Electrical diagrams .................................................7-8
7.3.1 Harness abbreviations .............................................7-8
7.3.2 Wire colors .....................................................7-8
7.3.3 Main electrical diagram ............................................7-9
7.4 Electrical tables ...................................................7-11
7.4.1 Circuit table ...................................................7-11
7.4.2 Connector function ..............................................7-12
7.4.3 Connector table .................................................7-12
7.4.4 Tractor connector ...............................................7-13
7.5 Hydraulic schematic ...............................................7-15
7.5.1 Hydraulic schematic .............................................7-17
8 Index .................................................................Index-1
Table of contents
Rotary Disc Header
4283612M1
Find manuals at https://best-manuals.com

Table of contents
Rotary Disc Header
4283612M1
Find manuals at https://best-manuals.com

1. General
1.1 General information .....................................................1-3
1.1.1 Introduction to this service manual .........................................1-3
1.1.2 Units of measurement ..................................................1-3
1.1.3 Table of contents .....................................................1-3
1.1.4 Page numbers .......................................................1-3
1.1.5 Intended use ........................................................1-3
1.1.6 Proper disposal of waste ................................................1-3
1.2 General safety ..........................................................1-5
1.2.1 Safety symbol ........................................................1-5
1.2.2 Safety messages .....................................................1-5
1.2.3 Information messages ..................................................1-5
1.2.4 Safety signs .........................................................1-5
1.2.5 Safety and informational signs ............................................1-6
1.2.6 Accumulator safety ....................................................1-8
1.2.7 A word to the technician ................................................1-8
1.2.8 The service manual ....................................................1-9
1.3 Operation .............................................................1-10
1.3.1 Prepare for operation ..................................................1-10
1.3.2 General information ...................................................1-10
1.3.3 Personal protective equipment ...........................................1-11
1.3.4 Seat instructions .....................................................1-11
1.3.5 Shield and guards ....................................................1-12
1.3.6 Exhaust warning .....................................................1-12
1.3.7 Flying debris ........................................................1-13
1.3.8 Handrails .......................................................... 1-13
1.3.9 Agricultural chemicals .................................................1-13
1.3.10 Travel on public roads ................................................1-14
1.4 Maintenance ...........................................................1-15
1.4.1 General maintenance information .........................................1-15
1.4.2 Bolt torque values ....................................................1-16
1.4.3 Fire prevention and first aid .............................................1-19
1.4.4 High pressure leaks ...................................................1-20
1.4.5 Tire safety ..........................................................1-20
1.4.6 Replacement parts ...................................................1-21
1.4.7 Remove an eccentric locking collar ........................................1-21
1.4.8 Install an eccentric locking collar ......................................... 1-21
1.4.9 Remove a gib key ....................................................1-22
1.4.10 Install a gib key .....................................................1-23
1.5 Specifications ..........................................................1-24
1.5.1 Maximum roading speed ...............................................1-24
1.5.2 Dimensions and weights ...............................................1-24
1.5.3 Header specifications .................................................1-24
1.5.4 Cutterbed specifications ...............................................1-24
1.5.5 Cutterbed bolt torque .................................................1-25
1.5.6 Conditioner specifications ..............................................1-25
1.5.7 Lubrication specifications ...............................................1-25
1.6 Machine identification ..................................................1-27
1.6.1 Machine identification .................................................1-27
1.6.2 Serial number plate ...................................................1-27
1.6.3 Serial number description ..............................................1-27
Table of contents
Rotary Disc Header 1-1
4283612M1

1.7 Machine description ....................................................1-29
1.7.1 Description .........................................................1-29
1.7.2 Cutterbed ..........................................................1-29
1.7.3 Conditioner .........................................................1-29
1.7.4 Swathboard ........................................................1-30
1.7.5 Forming shields ......................................................1-30
1.8 Component location ................................................... 1-31
1.8.1 Component location ..................................................1-31
1.8.2 Component access ...................................................1-31
1.9 Troubleshooting .......................................................1-32
1.9.1 Header troubleshooting ................................................1-32
1.9.2 Cutterbed troubleshooting ..............................................1-33
1.9.3 Conditioner troubleshooting .............................................1-34
1.9.4 Crop conditioning and windrow formation ...................................1-35
1.9.5 Cutoff quality .......................................................1-35
Table of contents
1-2 Rotary Disc Header
4283612M1

1.1 General information
1.1.1 Introduction to this service manual
This service manual gives information from engineering tests, operating data, and the latest service
techniques at the time of publication. Read this service manual carefully before doing any service on the
machine.
The photos and illustrations used in this service manual were current at the time of publication. Production
changes can cause machines to vary from the photos and the illustrations. The manufacturer reserves the
right to redesign and change machines as necessary without notification.
WARNING:
Some pictures in this manual show the machine with shields or guards removed to
permit for a better view of the subject of the picture. All shields and guards must be in
position before operating the machine.
Machine movement when in normal use determines right-hand and left-hand.
1.1.2 Units of measurement
Measurements are given in metric units followed by the equivalent in US units. Hardware sizes are given
in millimeters for metric hardware and inches for US hardware.
1.1.3 Table of contents
This manual has a table of contents at the front. The table of contents shows the divisions. The individual
divisions also have a table of contents.
1.1.4 Page numbers
All pages have two numbers, such as 01-25. The first number shows the division. The second number
shows the page in the division.
Page numbers occur on the lower right-hand or lower left-hand corner of each page.
1.1.5 Intended use
This machine is designed solely for use in customary agricultural operations.
Do not use this machine for any application or purpose other than those described in this manual. The
manufacturer accepts no liability for damage or injury resulting from misuse of this machine.
Compliance with the conditions of operation, service and repair as specified by the manufacturer constitute
essential elements for the intended use of this machine.
This machine should be operated, serviced and repaired only by qualified persons familiar with its
characteristics and familiar with the relevant safety rules and procedures.
All generally recognized safety regulations and road traffic regulations must be obeyed at all times.
Any unauthorized modifications performed on this machine will relieve the manufacturer of all liability for
any resulting damage or injury.
1.1.6 Proper disposal of waste
Improper disposal of waste can pollute the environment and ecology. A few examples of potentially
harmful equipment waste can include, but not limited to, items such as oil, fuel, coolant, brake fluid, filters,
battery chemicals, tires, etc.
Use leak proof containers when draining fluids. Do not use food or beverage containers to collect waste
fluids, as food or beverage container(s) may mislead someone into drinking from them.
[V]
GUID-D0FA2E94-0D28-42E9-A80B-6BB593BA9687 [V1]
GUID-EBB3FCAE-8712-43A9-BB65-1DB48189C57C [V2]
GUID-9BD2A110-651C-40FC-8D40-EDBAFD670A3C [V1]
GUID-6300C4A8-D25F-4B2F-BDC2-FAC58F99378B [V1]
GUID-939752D3-F912-4AFA-9CE0-FF5251AFAD3D [V3]
GUID-D27C9EFF-D3E3-4F5E-93ED-A6E5560C23DF [V3]
1. General
Rotary Disc Header 1-3
4283612M1

Do not pour or spill waste onto the ground, down a drain, or into any water source.
Air conditioning refrigerants escaping into the air can damage the Earth's atmosphere. Government
regulations may require a certified air conditioning service center to recover and recycle used air
conditioning refrigerants.
Inquire with local environmental or recycling center on the proper way to recycle or dispose waste.
1. General
1-4 Rotary Disc Header
4283612M1

1.2 General safety
1.2.1 Safety symbol
The safety symbol tells you about a dangerous
area!
Look for the safety symbol in this manual and on
the machine. The safety symbols tell you that
there is important safety instructions in the
manual.
GUID-4C201302-DBD2-4BFB-8D98-1DDED263BD6E-high.jpg [High]
Fig. 1
1.2.2 Safety messages
The words DANGER, WARNING or CAUTION are
used with the safety symbol. Learn these safety
messages and obey the recommended
precautions and safety instructions.
DANGER:
If you do not obey the recommended
precautions and safety instructions,
DEATH OR INJURY will occur.
WARNING:
If you do not obey the recommended
precautions and safety instructions,
DEATH OR INJURY can occur.
CAUTION:
If you do not obey the recommended
precautions and safety instructions,
INJURY can possibly occur.
GUID-73F05026-C37B-415A-8140-AD939A283378-high.jpg [High]
Fig. 2
1.2.3 Information messages
The words important and note are not related to personal safety, and are used to give information about
the operation and servicing of the machine.
IMPORTANT: Identifies special instructions or procedures which, if not followed, can cause damage to the
machine, the process, or the area around the machine.
NOTE: Information to make procedures easier.
1.2.4 Safety signs
WARNING:
Do not remove the safety signs. Replace safety signs that you cannot read, are damaged, or are missing.
Clean the machine surface with a weak soap and water solution before you replace the safety signs.
Replacement safety signs are available from your dealer.
[V]
GUID-5D9F270E-D748-4741-82B1-BE49B78685F2 [V4]
GUID-E54F7740-C021-42A8-8784-4287BE4356C8 [V4]
GUID-9A909F52-D57E-4C30-8CC7-6FDB6D7E9982 [V3]
GUID-2FB17168-6A01-47C5-B298-234AF171520B [V5]
1. General
Rotary Disc Header 1-5
4283612M1

Always make sure that safety signs are in the correct locations and that you can read the safety signs.
Illustrations of safety sign locations are at in this section.
Keep the safety signs clean. If necessary, use a weak soap and water solution.
1.2.5 Safety and informational signs
Front view
HAGHE0110376301
Original art: /s/Creo Illustrate/Images/Steve/9283 front view.svg
GUID-8D270105-53EC-4EA7-909E-E1CF0557FA3B-low.svg [Low]
Fig. 3
GUID-88EEBAA2-2AE3-4750-8DA7-7E3F1E9DF490 [V1]
1. General
1-6 Rotary Disc Header
4283612M1

Rear view
Original art: /s/Creo Illustrate/Images/Steve/9283 rear veiw.svg
HAGHE0110376701
GUID-90D7B0E7-3616-47AF-AC6E-0042E1EBBA28-low.svg [Low]
Fig. 4
Front view - reflectors
11
HAGHE0110376501
Original art: /s/Creo Illustrate/Images/Steve/9283 front view reflector.svg
GUID-716A7301-D012-4D2A-AF69-39C83CC2DA6B-low.svg [Low]
Fig. 5
(1) Yellow reflector
1. General
Rotary Disc Header 1-7
4283612M1

1.2.6 Accumulator safety
DANGER:
An authorized dealer must charge or
replace the accumulator.
The accumulator (1) is charged with dry nitrogen
gas. Use only dry nitrogen when the accumulator
is charged. Do not use air or oxygen or an
explosion will occur.
Nitrogen gas, when released can cause freezing.
Always wear protective gloves and glasses when
around nitrogen.
Do not let the accumulator fall. A charged
accumulator contains pressurized nitrogen. If the
shut off valve breaks away from the accumulator,
the nitrogen will make the accumulator move at a
high rate of speed.
GUID-8E9BDA96-9A48-4F66-A756-19C4E7FABDBD-high.jpg [High]
Fig. 6
1.2.7 A word to the technician
Read and understand the safety section in this
service manual before operating or servicing the
machine. Read and understand the safety sections
in the manuals for all attachments before
operating or servicing attachments. The technician
has the key to safety. Good safety practices
protect everyone.
Study the safety information in this service
manual. Make the safety information a working
part of the safety program. The safety information
in this service manual applies specifically to this
type of machine. Always do all other usual and
customary safe working precautions. Remember -
The technician has the responsibility for safety.
Good safety practices can prevent serious injury or
death.
The safety section points out some basic safety
situations that can occur during the operation and
maintenance of the machine. The safety section
also suggests possible ways to deal with these
situations. The safety section does not replace
safety practices in other parts of this service
manual.
Practice good safety to help prevent injury or
death.
Learn how to operate the machine and how to use
the controls correctly.
Do not let other persons operate the machine
without instruction and training.
Follow all safety precautions and instructions in
the manuals and on safety signs affixed to the
machine and all attachments.
GUID-AC91CCF6-1FF8-4A85-97A1-2D1562806825-high.jpg [High]
Fig. 7
GUID-ACCC65E0-C566-4487-937B-F08D7800DB09 [V8]
GUID-3C35D58D-1F5D-4B85-A915-C7BB48F47262 [V1]
1. General
1-8 Rotary Disc Header
4283612M1

Use only approved attachments and equipment.
Make sure the machine has the correct equipment
needed by the local regulations.
WARNING:
An operator should not use alcohol or
drugs which can affect their alertness
or coordination. An operator on
prescription or 'over the counter'
drugs needs medical advice on
whether or not they can properly
operate machines. If any attachments
used on this equipment have a
separate Operator Manual, see that
manual for other important safety
information.
1.2.8 The service manual
Read the table of contents and basic layout. Become familiar with all parts of this service manual. This
service manual gives the technician very important information.
Machine movement when in normal use determines right-hand and left-hand.
This manual covers general safety practices for this machine.
The photos, illustrations, and data used in this manual were current at the time of printing. Inline
production changes can make machines vary from the information in the service manual. The manufacturer
reserves the right to redesign and change the machine as necessary without notification.
WARNING:
In some of the illustrations and photos used in this manual, shields or guards may have
been removed for clarity. Never operate the machine with any shields or guards removed.
If the removal of shields or guards is necessary to make a repair, they must be replaced
before operation.
GUID-0CC50E5C-AD62-4FFD-9435-62214FEFA5F4 [V1]
1. General
Rotary Disc Header 1-9
4283612M1

1.3 Operation
1.3.1 Prepare for operation
Read and understand the operating instructions and precautions in this manual before you operate or do
servicing on the machine.
Make sure that you know and understand the positions and operations of all controls. Make sure that all
controls are in neutral and the parking brake is applied before you start the machine.
WARNING:
If the engine is running and the parking brake is not applied, the machine will turn if the
steering wheel is moved when the travel control lever is in neutral.
Make sure that all persons are a sufficient distance from your area of work before you start or operate the
machine. Do checks on the controls and learn all controls in an area clear of persons and objects before
you start work with the machine. Know the dimensions of the machine and have sufficient space available
for operation. Do not operate the machine at high speeds around persons, buildings, other equipment, etc.
Always use correct procedures when you do tasks around and operate the machine. Do not let children or
persons who do not know how to operate the machine operate the machine. Keep other persons away
from your area of work. Do not let other persons ride on the machine.
Make sure that the machine is in the good mechanical condition. Make sure that the machine has the
correct equipment as necessary by local regulations.
All equipment has a limit. Make sure you understand the speed, brakes, steering, stability, and load
characteristics of this equipment before you start.
1.3.2 General information
When parking, park the machine on a solid level
surface and lower the header to the ground. Put all
controls in neutral, and apply the parking brake.
Stop the tractor engine and take the key with you.
WARNING:
Do not leave the machine unattended
with the header raised. Lower the
header fully before leaving the
machine. A sudden loss of hydraulic
pressure can cause the header to
drop without warning.
Make sure the machine is in the proper operating
condition according to the Operator Manual.
Always operate the machine with the control
console turned on.
Do not dismount from moving machinery.
Stay off slopes too steep for operation.
Be aware of the size of the machine and have
enough space available to allow for operation.
GUID-E77631FB-0DC0-4637-9090-88018315176E-high.jpg [High]
Fig. 8
Stay off slopes too steep for operation. Keep the header as low as possible while going down hills. Never
suddenly reverse the wheels to stop or back up.
Where possible avoid operating the machine near ditches, embankments, and holes. Reduce ground
speed when operating on rough, slippery, or muddy surfaces and when turning or crossing slopes.
[V]
GUID-A9D74CBD-C409-4BEA-B8C1-A3DA5AE3C5EC [V4]
GUID-37023B41-C0ED-4F86-A909-1F42C1FE5D97 [V3]
1. General
1-10 Rotary Disc Header
4283612M1