Nav TV NTV-KIT899 User manual

C.O.D.-F5
Ford OEM 360 Surround-View Camera Controller
NTV-KIT899
3950 NW 120th Ave, Coral Springs, FL 33065 TEL [phone] FAX [phone]
BHM
11/12/18
NTV-DOC334

BHM
11/12/18
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
2 | P a g e
USB cable (updates)
NTV-CAB009
Overview
The COD-F5 (Camera-On-Demand) kit allows Ford SuperDuty trucks equipped with OEM (5-camera
system) surround view cameras to be displayed on demand, without lock-out restrictions. Additional
features include turn signal cameras, easy force rear cam & force front cam & last known camera
retention (from hard camera button press). NOTE: This kit will NOT program any camera system. This
module is only intended for use in SuperDutys equipped with the OEM trailer package (5-camera
system).
Kit Content
COD-F5 Module Pin Out
Pin #
Description
Color
1
12v Constant Power (+)
Yellow
2
INPUT 1: Force External Camera
Red
3
INPUT 2: NOT USED
Blue
4
INPUT 3: NOT USED
Pink
5
RX (OE camera button –button side)
Blue
6
CAN-3 HIGH (camera module)
Blue
7
CAN-2 HIGH (CAN gateway)
Blue
8
CAN-1 HIGH (APIM)
Yellow
9
CAN-0 HIGH (CAN gateway)
Yellow/Black
10
Ground (-)
Black
11
OUTPUT 1: NOT USED
White/Red
12
OUTPUT 2: NOT USED
White/Blue
13
OUTPUT 3: NOT USED
White/Purple
14
TX (OE camera button –module side)
Purple
15
CAN-3 LOW (camera module)
Purple
16
CAN-2 LOW (CAN gateway)
Purple
17
CAN-1 LOW (APIM)
Orange
18
CAN-0 LOW (CAN gateway)
Orange/White
Wire side
COD-F5 Module
NTV-ASY301
Plug & Play T-Harness
NTV-HAR329

BHM
11/12/18
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
3 | P a g e
COD-F5 Installation
1. Remove the 8” SYNC 3 screen (radio):
a. Remove the center channel speaker cover on the top (middle)
of the dash (4 clips only).
b. Remove (2) 7mm bolts securing the top
panel (previously hidden by the speaker
grill).
c. Remove the whole upper shelf panel, it
should be held in by clips only, now.
Disconnect the speaker lead. Set this
panel assembly aside.
d. Remove (2) 7mm screws on top of the climate/screen dash
panel, and then pull panel straight towards you. Disconnect
all harnesses and set the panel aside.
e. Remove (6) 7mm screws securing the screen (APIM) to
the sub-dash. Disconnect all harnesses and set the
APIM aside.

BHM
11/12/18
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
4 | P a g e
2. Connect the provided T-Harnesses between the vehicle harness and the APIM (screen), and
from the vehicle harness and the OEM camera module (directly behind screen).
3. Optional: If the user wants to use an analog trigger for camera display, wire the INPUT (for the
forced feature desired) to a toggle switch so that the INPUT wire receives 12v (+) when
activated. See pin out chart on page 2.
4. Connect the 18-pin plug to the VIM module and secure it in the sub-dash so that nothing
rattles. NOTE: No other wires from the unit are used for this installation.
5. Return the screen to the sub-dash and reconnect the climate/screen surround panel for testing.
6. Proceed to ‘COD-F5 Operation’.
IPM (camera module)
Rear of APIM (screen)
COD-F5

BHM
11/12/18
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
5 | P a g e
*NOTE: to disable turn signal camera activation,
press and HOLD the camera button for 20 seconds
(wait for tone). Once complete, turn signals
cameras will deactivate. Repeat this process to
reactivate TSC at any time.
COD-F5 Operation (SuperDuty)
Once the COD-F5 module is connected properly, all added camera commands are performed through
the factory camera button. Added features are outlined below:
•Camera button now shows rear camera (default after ignition) with a single press
(press and release once again to clear)
•Camera button now shows front camera with a double press (press and release
once again to clear)
•Last used camera image (whether front, rear, cargo or surround view) is
retained when switching back and fourth from radio screen to camera screen via
camera button (instead of default surround view only with each press)
•Turn signals switch to corresponding side view (left or right, panned 100%) *

BHM
11/12/18
NTV-DOC334
Agreement: End user agrees to use this product in compliance with all State and Federal laws. NAV-TV Corp. would not be held liable for misuse of
its product. If you do not agree, please discontinue use immediately and return product to place of purchase. This product is intended for off-road
use and passenger entertainment only.
6 | P a g e