NEC UNIVERGE SL2100 User manual

The SL2100
Quick Install Guide:
Analogue
Trunks
www.nec-enterprise.com

NEC SL2100 Communication System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 2
This guide explains the installation, configuration and operation of the SL2100 Telephone System including the
exchange line and telephone connections.
Further information is available on BusinessNet.
Please keep all information supplied for future reference.
Regulatory Notice.
Refer to the Declaration of Conformity shown in the SL2100 Hardware Manual
Warning: This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

NEC SL2100 Communication System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 3
Contents
What is the SL2100?...............................................................................................................................................4
Outside lines (Analogue Trunks) included in this guide.....................................................................................4
Parts available for the SL2100...........................................................................................................................5
System Overview....................................................................................................................................................6
Installation Procedure............................................................................................................................................7
Power Fail Operation..........................................................................................................................................7
1- Unpack the SL2100 System...............................................................................................................................8
2- Install the Analogue Trunk Card.......................................................................................................................9
Mounting the 3COIDB Daughter card ................................................................................................................9
308 Trunk + Extension card ...............................................................................................................................9
Removing the Plastic Knockouts......................................................................................................................10
Installing into the Universal Slot.......................................................................................................................11
3- Install the CPU Card.........................................................................................................................................12
4a- Wall Mount the SL2100 system.....................................................................................................................14
4b- Rack Mount the SL2100 system ...................................................................................................................16
5- Connect the Telephones..................................................................................................................................17
6- Connect the External Music on Hold Device.................................................................................................17
7- Connect the Exchange Lines ..........................................................................................................................18
Connecting to the RJ45 socket of the Analogue Trunk card............................................................................18
8- Connect the Power & System Start Up ..........................................................................................................20
9- Configure the SL2100.......................................................................................................................................21
Connecting PCPro to the SL2100....................................................................................................................21
Change your PC IP Address............................................................................................................................22
SL2100 PCPro..................................................................................................................................................23
PCPro Initial Setup Wizard...............................................................................................................................24
Set Time & Date and Upload to the SL2100....................................................................................................29
Repeat Wizard or Finish...................................................................................................................................29
Make Additional Changes with PCPro .............................................................................................................30
Incoming Ring Groups......................................................................................................................................31
Trunk –Outgoing Trunk Access.......................................................................................................................32
Automatic Night Mode Schedule......................................................................................................................33
Extension –Programmable Function Keys......................................................................................................34
Extension - Toll Restriction...............................................................................................................................36
What to do if you make errors within the SL2100 Configuration......................................................................37
10- Security............................................................................................................................................................38

NEC SL2100 Communication System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 4
What is the SL2100?
The SL2100 system consists of a chassis unit with a dedicated slot for the CPU
card and four universal slots for interface cards. Each universal slot supports an
extension interface card, optionally each extension interface card can have a trunk
interface daughter card mounted.
The chassis unit is ventilation cooled (no fan) and can be wall mounted or rack
mounted with the optional rack mount shelf.
Up to three chassis units can be connected together to provide a total of twelve
universal slots.
Interface cards are available for Analogue and ISDN trunks, proprietary SL2100
terminals and analogue telephones.
SIP Trunks and IP terminals are supported without the need for additional system
hardware as eight VoIP resources are built in to the CPU card. VoIP resources can
be expanded to 16 by adding the optional VOIPDB card and further to 128 with
licenses.
InMail voicemail is also available either using the built in storage of the CPU-C1-A or by adding the optional SD
card.
The built in InMail with the CPU-C1-A card provides 4channels and 2hours of storage, this can be expanded to
15hour or 120hour by adding the SD card to the CPU.
The CPU-C1 requires the SD card installed to provide InMail voicemail.
Both CPU’s have built in VRS with 4channnels and 100 messages with 2hours message storage.
All equipment will operate in the default/factory setting when the SL2100 is installed.
With the default settings:
Each telephone will function and is assigned an extension number.
Calls received on the Analogue trunk lines will ring at telephone number 200.
Each telephone can make outside calls by dialing 9.
Each trunk line is presented at a Function Key with busy lamp indication.
The system can be easily modified using SL2100 PCPro which has Quick Installation wizards for the majority of
system settings.
Outside lines (Analogue Trunks) included in this guide
The SL2100 has two cards that provide analogue trunks:
IP7WW-308U-A1 –Provides 3 analogue trunks and 8 Hybrid extension interfaces and is installed into one of
the universal slots
IP7WW-3COIDB-C1 –Provides 3 analogue trunks and is a daughter card that is mounted onto one of
extension interface cards (IP7WW-082U-B1 or IP7WW-008U-C1) or the trunk carrier card (IP7WW-000U-
C1)
You can install up to four trunk interface cards within the SL2100 main unit.
The trunk interface card has three connections providing 3 trunks
The trunks connected must be loop start type
Line are connected via a single RJ45 8/8 way socket

NEC SL2100 Communication System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 5
Parts available for the SL2100
Not all parts are included within this guide, please refer to the other SL2100 Quick Install Guides or the SL2100
Hardware Manual for a full description and installation instructions of all parts available.
IP7WW-4KSU-C1
SL2100 Chassis unit
Included within this guide
IP7WW-3COIDB-C1
Analogue trunk daughter card
IP7EU-CPU-C1
SL2100 CPU card
IP7EU-CPU-C1-A
SL2100 CPU card with pre-
installed IP licenses and 2hour
InMail
IP7WW-EXIFB-C1
Expansion interface card
Interface card required to connect to the
expansion chassis
IP7WW-EXIFE-C1
Expansion interface card
Interface card installed into the expansion
chassis
IP7WW-SDVMS-C1
IP7WW-SDVML-C1
InMail voicemail
Provides 15/120 hour voicemail
IP7WW-2BRIDB-C1
2BRI card
2 x ISDN BRI circuits, 4 trunks
IP7WW-1PRIDB-C1
ISDN PRI card
1 x PRI circuit, up to 30 trunks
IP7WW-000U-C1
Trunk carrier card
Require when 082E or 008E card is not
available to install the 2BRIDB,1PRIDB or
3COIDB card
IP7WW-082U-B1
8 Digital Extension (2wire) and 2
SLT extension card
8 digital and 2 SLT extension interfaces, max
3 per unit
IP7WW-308U-A1
8 Hybrid Extension (4wire)
extension card
8 hybrid extension interfaces, max 4 per unit
IP7WW-008U-C1
8 Analogue extension card
8 analogue extension interfaces, max 4 per
unit
IP4WW-Battery Box
Battery box
External battery box for power fail backup
(batteries not included)
161893001-A
Rack mount shelf
Rack mount for SL2100 chassis unit
Refer to Prophix for all parts and licenses available in your region.
SL2100 Terminals are included in separate Quick Install Guides

NEC SL2100 Communication System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 6
System Overview
SL2100 chassis showing the CPU card and an interface card with analogue trunks.
The slots are labelled S0~S4 on the front of the chassis.
Slot S0 has the CPU card installed, slots S1~S4 are universal slots for any interface card.
Note –Slot 4 does not support digital extensions, an IP7WW-082U-B1, IP7WW-308U-A1 or IP7WW-008U-C1
card can be installed but will only support analogue extensions, any trunk daughter card is supported in slot 4.
SL2100 Capacity
Item
Maximum capacity
in a single chassis
TDM Trunks
42
There is a trade-off between each trunk type, see below
Analogue
12
ISDN BRI
16
ISDN PRI
30
SL2100 Trunk capacity for a single chassis
Extension
Interface card
3 x Analogue
Trunks
SL2100 CPU card

Installation Procedure
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 7
Installation Procedure
1
Unpack all items and check
for damaged or missing parts.
See page 8 for details.
2
Install the trunk card
See page 9 for details.
3
Install the CPU card
See page 12 for details.
4
Mount the SL2100 system on
the wall or in the rack
See page 14 for details.
!Within suitable cabling distance from the exchange lines.
!Within suitable distance from a power socket and Earth point.
!Check the other installation considerations in section 3.
5
Connect the telephones.
See separate Quick Install Guide for the terminal type being installed
6
Connect the External MOH
Device.
Optional
See separate Quick Install Guide for the terminal type being installed
7
Connect the exchange lines.
See page 18 for details.
8
Connect the power and switch
on the SL2100.
See page 20 for details.
9
Configure the SL2100 to the
customer’s requirements.
See page 21 for details.
Use SL2100 PCPro software
10
Security
Ensure the system is protected against Toll Fraud and has secure
maintenance passwords
!
Consider the operation during
power failure
Will require additional parts if required
Power Fail Operation
In event of a power failure, the trunk connections are not automatically rerouted. For power failure it is
recommended to connect a socket for each Analogue trunk in parallel with the SL2100.

Unpack the SL2100
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 8
1- Unpack the SL2100 System
SL2100 Chassis unit
1 x SL2100 system
1 x Wall mounting template
1 x Power cord (selected regions)
4 x Fixing screws (M4.1 x 25mm)
SL2100 CPU card
1 x CPU card
1 x Lithium battery (CR2032)
SL2100 Extension Interface card
1 x Interface card
SL2100 3COIDB card
1 x 3COIDB card
1 x Screw & spacer
Additional Items Required:
Cross head screwdriver.
Utility knife or small flush cutters to remove the plastic knockouts
4 Wall fixing plugs suitable for the type of wall.
Solid wire for extending telephone cabling:
Recommended cable type: Twisted pair (CW1308 or similar specification)
Conductor diameter: 0.4 to 0.6 mm
Maximum cable length: (with 0.5 mm diameter cable)
SL2100 system telephone –300 metres
Normal telephone (SLT) –1125 metres
If you need to extend the exchange line cables:
Solid wire for exchange line cables:
Recommended cable type: Twisted pair (CW1308 or similar specification)
Conductor diameter: 0.4 to 0.6 mm

Install the 3COIDB Card
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 9
2- Install the Analogue Trunk Card
The SL2100 chassis does not have any trunk ports pre-installed, you install the trunk card of your choice.
! Ensure the SL2100 is powered off before removing/installing any card.
Mounting the 3COIDB Daughter card
The IP7WW-3COIDB-C1 card is a daughter card that must be installed onto any of the following interface cards:
IP7WW-000U-C1
Trunk carrier card
IP7WW-082U-B1
8 Digital Extension (2wire) and 2 SLT extension card
IP7WW-008U-C1
8 Analogue extension card
Each interface card can have one daughter card installed.
Remove the plastic knockout from the front panel of the interface card. The COI interface blade only requires
one of the two knockouts to be removed. Check alignment of the knockouts with the daughter card.
The IP7WW-3COIDB-C1 card is supplied with two Nylon pillars already installed and a securing screw and metal
spacer.
Align the 3COIDB board Nylon spacers and connector with the SL2100 interface card and push in firmly.
Secure the 3COIDB with the screw through to the metal spacer.
308 Trunk + Extension card
The IP7WW-308U-A1 card is an extension interface card with 3 analogue trunks included, this card does not
require any daughter card mounting and can be installed into any of the universal slots –Note that slot 4 does
not support digital extensions.

Install the 3COIDB Card
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 10
Removing the Plastic Knockouts
KSU slot knockouts
Use small cutters with a flush cutting jaw, ensure the flush side of the cutter is towards the front panel of the
KSU.
Remove the connection points in the order shown:
1. Cut the two end points
2. Cut the two points closest to the outer edge of the KSU
3. Push the knockout slightly in at the outer edge (do not snap off the remaining points)
4. Cut the two remaining points closest to the inner edge of the KSU
Remove any sharp edges with a utility knife
Card knockouts
Use small cutters with a flush cutting jaw, ensure the flush side of the cutter is towards the front panel of the
card.
Cut the three connection points for each left/right knockout depending in the trunk daughter card being installed
Remove any sharp edges with a utility knife
1
1
2
2
4
4
3 - push
Ensure the flush side of the
cutter is towards the front
panel of the KSU
Ensure the flush side of the
cutter is towards the front
panel of the card

Install the 3COIDB Card
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 11
Installing into the Universal Slot
Remove the plastic knockout from the slot on the front of the SL2100 chassis.
Any universal slot can be used, it is recommended that you install the cards using slot order 1->4. Slots are
identified S1~S4 on the front of the chassis.
Note –The knockout can not be replaced once removed; there are no blanking covers available, be sure to
remove the correct knockout.
Note –Slot 4 does not support digital extensions.
Insert the interface card into the SL2100 universal slot, ensure the card slides into the guide rails and tighten the
two screws to secure the card.
The type of trunk daughter card installed can be identified by the RJ45 sockets visible on the front of the
interface card.

Install the CPU Card
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 12
3- Install the CPU Card
The SL2100 chassis does not have any CPU card pre-installed, you install the card of your choice.
There are two CPU card available:
IP7EU-CPU-C1
SL2100 Main Processor Board
• VoIPDB Daughter Board Connector : 1
• EXIFB Daughter Board Connector : 1
• SD Card Slot : 1
• Built-in 4ch of VRS (Not supported for VM without SDVML/SDVMS)
• Built-in 8ch VOIP resources
IP7EU-CPU-C1-A
The hardware is same as IP7EU-CPU-C1.
The feature Includes:
• Built-in 4ch of VRS/InMail voicemail
• 4pc of SL2100 IP TRUNK-01 LIC
• 4pc of SL2100 IP EXT-01 LIC
Ensure the SL2100 system is powered off before removing or inserting the CPU card.
Fit the memory backup battery (CR2032 type)
The + symbol must be on top, as shown below.
Fit the optional items to the CPU card, if applicable:
IP7WW-SDVMS-C1 /
P7WW-SDVML-C1
SD Card for VRS/VM (InMail) Storage 15/20 hour
IP7WW-EXIFB-C1
System Expansion Bus Daughter Board (mount to CPU)
• 2 Bus connectors for Expansion Chassis
• Additional Telephony Resources
• VRS/VM (InMail) Channels expansion (up to 16ch)
• Analog Modem (V.34)
P7WW-VOIPDB-C1
VoIP GW Daughter Board (mount to CPU) 16ch VOIP resources, maximum
128ch with licenses
Note –Both CPU cards may not be available in your region.

Install the CPU Card
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 13
Insert the CPU card mounted into the SL2100 CPU slot S0, ensure the card slides into the guide rails and
tighten the two screws to secure the card.

Wall/Rack Mount the SL2100 System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 14
4a- Wall Mount the SL2100 system
Installation Considerations:
To avoid electric shock or damage do not plug in or turn on the system power before completing the
installation.
Avoid working with the system during electrical storms.
Use the power cord supplied with the product.
Do not bundle power cords together, the cords may overheat.
Ensure the system has a suitable Earth Ground connection.
Environmental Considerations –Be sure the system is not:
In direct sunlight or in hot, cold or humid places.
In dusty areas or in areas where sulfuric gasses are produced.
In places where shocks or vibrations are frequent or strong.
In places where water or other fluids may come into contact with the equipment.
In areas near electric welders or machines that emit high frequency radiation.
Near computers, microwaves, air conditioners etc.
Near radio antennas (including shortwave).
If you are installing the optional expansion cabinets ensure there is sufficient wall space and ventilation.
Refer to the wall mounting diagrams below.
1
Allow 930mm x
875mm (W x H)
wall space for the
SL2100 system.
The system is
330mm x 435mm
x 93mm
(W x H x D)
!You will need
more space if you
are installing
optional expansion
cabinets.
Refer to the
SL2100 Hardware
Manual for
instructions.
Fit three screws to
the wall in the
holes shown.
Leave 2.5~3.5 mm
stand off.
Hook the SL2100
chassis onto the
three screw
heads.
Ensure the wall surface is flat and that you use the correct wall plugs for the type of
wall material. Screws are supplied with the SL2100 chassis.

Wall/Rack Mount the SL2100 System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 15
Secure the
chassis to the wall
with a screw.
2
Earth the SL2100
system.
Important. The system must have a permanent Earth Ground connection to a
verified Earth point using a minimum of 14AWG/2.5mm2cable.
The Earth connection must have no other purpose than connecting to the SL2100
unit.

Wall/Rack Mount the SL2100 System
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 16
4b- Rack Mount the SL2100 system
Installation Considerations:
If the system requires two or three chassis then each chassis will require a shelf plate within the 19 inch
rack, must be space above each chassis for heat ventilation.
Do not stack two or three chassis per one shelf plate.
1
Use the rack
mount shelf
supplied by NEC.
3rd party shelves
may block the side
ventilation and do
not provide any
securing method
!Ensure 44.5mm
space above each
chassis for
ventilation. The
shelf is oversize
(100mm high) to
ensure space is
provided.
Confirm the
location of the
rack mount shelf
and fit the four
cage nuts supplied
with the shelf
Fit the chassis into
the rack mount
shelf and secure
with the screw
supplied.
Fit the rack mount
shelf + chassis
into the 19 inch
rack and secure
the shelf with the
four screws
supplied
3U space will be required for each KSU.
Rack mount shelf requires 448mm x 337mm x 100mm (W x D x H) within the rack.
The AC power cable enters at the rear of the chassis, allow ~60mm for space at the
rear.
Ventilation is required above the chassis.
You may need to connect the AC power cable and Earth Ground cable to the rear of
the chassis prior to installing into the rack if you do not have sufficient space/access
to do this afterwards.

Connect the Telephones
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 17
5- Connect the Telephones
Refer to the Quick Install Guide for the type of terminals you will be connecting:
SL2100 Quick Install Guide –Terminals (Type A)
SL2100 Quick Install Guide –Terminals (Type B)
These guides also include details of connecting the following items:
Doorphone units
DSS consoles
6- Connect the External Music on Hold Device
Refer to the Quick Install Guide for MOH and External Audio.

Connect the Exchange Lines
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 18
7- Connect the Exchange Lines
The SL2100 chassis does not have any trunk ports pre-installed, you install the trunk card of your choice.
Analogue Trunk
Trunk port allocation
CO 1
Trunk port 1
CO 2
Trunk port 2
CO 3
Trunk port 3
Connecting to the RJ45 socket of the Analogue Trunk card
The are several methods available to connect these interfaces into the customer’s building infrastructure.
1. Use the cable assembly or adapter available from NEC
Cable LPNEC3 –2m length, converts a four port RJ45 socket to four RJ45 plugs, one port per plug.
Can be used to connect into an RJ45 through coupler panel or directly into the customer’s
panels.
Can also be used to plug into RJ45 face plates if IDC termination is required.
Cable colour: black
One cable is required for each Trunk/COI socket of the IP7WW-308U-A1 or IP7WW-
3COIDB-C1 card.
Ports 1~3
RJ45 plug
Pin
1
-
2
-
3
-
4
R
5
T
6
-
7
-
8
-

Connect the Exchange Lines
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 19
Adapter ADNEC14 –Converts a four port RJ45 socket to four RJ45 sockets, one port per socket.
Requires four patch cables of the desired length and colour when used for analogue trunk connections.
Can be used to connect into an RJ45 through coupler panel or directly into the customer’s panels.
Can also be used to plug into RJ45 face plates if IDC termination is required.
Colour: black
Supplied with an adhesive pad.
One adapter is required for each Trunk/COI socket of the IP7WW-308U-A1 or IP7WW-3COIDB-C1 card.
2. Terminate cables on site with RJ45 plugs and connect directly to the RJ45 sockets of the IP7WW-308U-A1
or IP7WW-3COIDB-C1 card.
Use the following pin-out to terminate each RJ45 plug.
Trunk/COI
Pin
No.
Port
1
2
3
3
2
4
1
5
1
6
2
7
3
8
3. Use pre-terminated RJ45 patch cables and connect directly to the RJ45 sockets of the IP7WW-308U-A1 or
IP7WW-3COIDB-C1 card.
Use the following cable colours when using a straight through RJ45 patch cable directly into the RJ45 sockets of
the IP7WW-308U-A1 or IP7WW-3COIDB-C1 card.
Using an RJ45 patch
cable into the RJ45
connectors
Trunk / COI
Pin
No.
Port
RJ45 Colour code
1
White/Orange
2
3
Orange/White
3
2
White/Green
4
1
Blue/White
5
1
White/Blue
6
2
Green/White
7
3
White/Brown
8
Brown/White
87654321
87654321
Ports 1~3
RJ45 sockets
Pin
1
-
2
-
3
-
4
R
5
T
6
-
7
-
8
-

Connect the Power & Start Up
Quick Install Guide –SL2100 with Analogue Trunks rev 1.1 20
8- Connect the Power & System Start Up
The power cable is plugged into the left side (wall mounted) or rear (when rack mounted) of the unit via an IEC-
C13 connector.
Before connecting the power:
Ensure the power switch is OFF
Ensure the power is switched off at the source
All cards are installed and secured correctly
System Start Up –First Time
!The first time you start up the SL2100 it is important to clear the system memory. This will ensure that the
system is set to the default/factory configuration.
1. Push and hold the LOAD Button located on the front of the CPU card.
2. Turn the power switch on
3. Continue holding the LOAD Button for approximately 10 seconds or until the ALM lamp on the CPU card
lights.
4. Release the LOAD Button
5. When the system has completed reloading the system software (about one minute) the RUN LED is
flashing green on the CPU card and the system phones will display the Time and Date.
Switching the SL2100 OFF
!Be sure that no calls are in progress otherwise they will be cut off.
Turn the power switch OFF at the SL2100 chassis.
System Start Up –Retain Customer Configuration
This is the normal operation for powering the SL2100 on.
Turn the power switch ON at the SL2100 chassis
Also referred to as ‘COLD Start’
can also be used at any time to
delete the customer’s
configuration.
Warning –COLD Start should
only be used when you want to
delete the customer’s
configuration from the SL2100
CPU card.
AC Power
cable
Power
switch