No Butts Bin SR7894 User manual

Assembly Instructions
Product Code: SR7894
Doc. No.: SR7894-01-27092021-USA
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]

2
10 9
9
10
7
10
11
3
1
8
1
6
12
11
1
4
2
3
3
8
5
3
5
7
Exploded view
ITEM
NO.
PART
NO.
DESCRIPTION
DIMENSION IMAGE
QTY.
1
S1
Frame
2000 x 1035
5
2
JF1
Straight Bracket
220 x 40
3
3
CB1
Corner Bracket
110 x 110 x
40 7
4
ST1
Beam
1025 1
5
DR
Rafter Bracket
110 x 40 x 52
8
6
FT1
Foot Bracket
109 x 100 x
40 2
7
DR1R
Rafter
1142.5 3
8
DR1I
Infill Panel
1134 x 200
2
9
DR1PO
Roof Panel Outer
1211 x 1055
2
10
DR1T
Roof Trim
1211 x 80
3
11
DRAT2
Ally-Angle Trim 2M
50x50x2110
2
12
FT3
FT3 Bracket
109 x 100 x
80 4
13
EC40
Plastic end cap
STD. STOCK
ITEM
2

Parts List
3
ITEM
NO.
PART
NO.
DESCRIPTION
Size (inch) IMAGE
QTY.
1
S1
Frame
78.74 x 40.74
5
2
JF1
Straight Bracket
8.7 x 1.6
3
3
CB1
Corner Bracket
4.3 x 4.3 x 1.6
7
4
ST1
Beam
40.4 1
5
DR
Rafter Bracket
4.3 x 1.6 x 2
8
6
FT1
Foot Bracket
4.3 x 3.9 x 1.6
2
7
DR1R
Rafter
45 3
8
DR1I
Infill Panel
44.6 x 7.9
2
9
DR1PO
Roof Panel Outer
47.7 x 41.5
2
10
DR1T
Roof Trim
47.7 x 3.1
3
11
DRAT2
Ally-Angle Trim 2M
2 x 2 x 83
2
12
FT3
FT3 Bracket
4.3 x 3.9 x 3.1
4
13
EC40
Plastic end cap
1.6 x 1.6
2

Tools required:
Drill/Screwdriver
Mallet
Tools included:
WRENCH
Torx bit
4
*
NOTE: THE 1 1/2 inch TECH SCREWS ARE FOR FIXING ROOF COMPONENTS ONLY
Fittings and tools
Type Bolt set M10 T25
T38
*
BTANCM12100
M10 x 60 Nut Washer
Black
Caps
1" Tech
screw
1 1/2"
Tech
screw
M10/12 x 100 mm
Concrete Bolt
Pack A
30 30 60 60 72 30 8
Image

IMPORTANT:
Make sure side frames are aligned as detailed below.
CB1 Bracket CB1 Bracket
Aligned with
the outside
Aligned with
the inside
S1 Frame
S1 Frame
S1 FrameS1 Frame
CB1
CB1
CB1
CB1
JF1
JF1
83"
40 1
2
"
Step 1
Assemble back and side frames S1 as shown below.
5
Check the dimension
of the shelter to
ensure correct alignment

ST1
CB1
CB1
CB1
JF1
S1 FRAME
42 1
2
"
83"
42 1
2
"
83"
CB1
CB1
CB1
ST1
S1
S1
S1
S1
S1
Step 2
Attach front S1 frame and ST1 tie bar using CB1 brackets in the corners and
JF1 brackets on the straight joints.
6
Check the dimension
of the shelter to
ensure correct alignment

DR
DR1R Rafter DR1R Rafter
DR1R Rafter
DR
DR
DRDR
DRDR
DR
DR1I
DR1I
Secure the DR1R roof rafters into place using the DR Brackets. The DR1I
infill panels are screwed into place using 1" tech screws but must be
placed into position at the same time as the end rafter.
DR1R
DR
DR1I
DR1I
40 1
2
" 40 1
2
"
Front View
Step 3
7

DR1T
Roof sheets
DRAT2
DRAT2
Step 4
8
NOTE:
THE 1 1/2" TECH SCREWS ARE
FOR FIXING ROOF STRIPS
(DR1T) ONLY
Stick sealing strips on top of rafters and install roof sheets. Seal the central gap
and edges with a DR1T strip. Install the DRAT2 Angle trim to the bottom of the
roof panels. Then fit the black plastic caps on exposed nuts and bolts.

39 1
2
"
41"
83"
45 1
2
"
3 1
2
"
2 1
2
"
41"
41"
40 1
2
"
44 1
2
"
Plan View
Suggested size for concrete base: 8 inch oversized on all 4 sides.
9

10
CONTACT DETAILS:
No Butts Bin Company, Inc.
16 Birch Lane, Madison, CT 06443
Email : [email protected]
Web : www.nobutts.com
Tel : [phone]
MAINTENANCE:
To ensure your products give you many years of use we recommend that you:
THANK YOU
FOR PURCHASING THIS PRODUCT
Clean panels regularly with soapy water •
Ensure all fittings are tight (for example after a big storm) •
Use metal paint to touch up any exposed metal •
should it get scratched
All Parts and Fixings checked by:
Print Name: Signature: