Norco MITX-6110 User manual

MITX-6110
User’s Manual V1.0

Announcement
With the exception of showing the accessories of product configuration, this
manual does not create any commitment of our company. We retained the
rights to change it without prior notice and will not be responsible for any
direct, indirect, intentional or unintentional damage or hidden dangers
caused by any improper installation or use.
Before buying products, please learn about the product performance from
the distributors to see if it is in line with your needs. NORCO is a registered
trademark of Shenzhen NORCO Intelligent Technology CO., LTD. The
ownership of other trademarks involved in this manual is owned by its
respective owners.
The contents of this manual are protected by copyright law. All rights are
strictly reserved. Any form of unauthorized reproduction is prohibited,
including but not limited to carbon copy, facsimile transmission and
electronic copy or email, etc.

Safety Instructions
1.Before using this product, please read this user’s manual carefully;
2.Any plate cards not ready to be installed shall be kept in the anti-static protective bags;
3.Before taking out the plate cards from the anti-static protective bags, first place hands on the
grounding metal object for a while so as to release the static electricity from your body and
hands;
4.While fetching the plate cards, please wear static protective gloves and have the habit of
holding the cards by edge;
5.Before connecting the motherboard to the power supply, please check the power voltage
6.In order to prevent bodily electric shock or damage to products, first turn off the
AC power or unplug the power cord out of power sockets while inserting main boards or plate
cards or do reconfiguration;
7.Before moving the plate cards or the unit, please make sure to unplug the AC power cords
out of the sockets;
8.Before you connect or unplug any equipment, please make sure that all power cords are
unplugged in advance;
9.To prevent any unnecessary damage to the products due to frequent power on/off. Please
wait at least 30 seconds before you restart up the unit after the unit is shut down;
10.If anything unexpected happened during the operating, please seek help from
professionals;
11.This is a Class A product, in a domestic environment, this product may cause radio
interference. In this case, the user may be required to take adequate measures.

Content
Chapter 1 Product Introduction...........................................................................................................1
1.1 Product Specification................................................................................................................ 1
Chapter 2 Installation Instructions...................................................................................................... 3
2.1 Interface Location and Dimension Diagram..........................................................................3
2.2 Installation Steps....................................................................................................................... 3
2.3 Memory Installation...................................................................................................................4
2.4 Jumper Setting...........................................................................................................................4
2.4.1 CMOS Content Clearance /Keep Settings（JCC1、JCC2）................................4
2.4.2 Hardware Switch for System Auto Boot upon Power On（JAT）..........................6
2.4.3 Debug Interface（DB_UART）................................................................................... 7
2.4.4 COM2 Jumper Setting（J1，J2）............................................................................. 7
2.5 Interface Specification.............................................................................................................. 8
2.5.1 SATA Interface（SATA1、SATA2、JSATAPWR、MCU_DB）.............................8
2.5.2 Serial Ports（HDMI JCOM1、VGA JCOM2）.....................................................10
2.5.3 Display Port（LVDS）................................................................................................ 12
2.5.4 LVDS Voltage and Backlight Setting Interface（JLVDS、JLVDSBTN、JLVDSPWR）
.................................................................................................................................................. 14
2.5.5 USB Port（USB12、USB34、USB56_USB3_LAN1、USB78_USB_LAN2）15
2.5.6 Keyboard & Mouse Connector（KBMS）............................................................... 16
2.5.7 Programmable I / O Interface（JGP）.....................................................................17
2.5.8 Power Interface（PWR1、PWR2、PWR3）......................................................... 18
2.5.9 Fan Interface（SYS_FAN、CPU_FAN）................................................................ 19
2.5.10 Line Input Pin（LINE_IN）...................................................................................... 20
2.5.11 JLPC Interface（JLPC）..........................................................................................20
2.5.12 Audio Port（Audio）................................................................................................. 22
2.5.13 BIOS Write Protect Interface（JME）................................................................... 23
2.5.14 Front Panel Interface（JFP）................................................................................. 23
2.5.15 Memory Slot（SO-DIMM）......................................................................................25
2.5.16 Expansion Por（PCIE_X1、MINI_ PCIE1、MINI_ PCIE2）.............................25

Chapter 3 BIOS Setup....................................................................................................................... 25
AMI BIOS Reflesh..................................................................................................................25
AMI BIOS Description........................................................................................................... 25
BIOS Parameter Setting....................................................................................................... 25
3.1 Main Menu................................................................................................................................26
3.2 Advanced..................................................................................................................................27
3.2.1 ACPI Settings............................................................................................................... 28
3.2.2 CPU Configuration.......................................................................................................29
3.2.3 SATA Drives................................................................................................................. 31
3.2.4 USB Configuration.......................................................................................................32
3.2.5 F81804 Supper IO Configuration.............................................................................. 33
3.2.6 Hardware Monitor........................................................................................................ 35
3.2.7 Serial Port Console Redirection................................................................................ 36
3.2.8 LAN Configuration....................................................................................................... 37
3.2.9 Network Stack Configuration..................................................................................... 38
3.2.10 CSM Configuration.................................................................................................... 39
3.3 Chipset Menu...........................................................................................................................40
3.3.1 North Bridge.................................................................................................................41
3.3.2 South Bridge................................................................................................................ 42
3.3.2.1 PCI Express Configuration......................................................................................43
3.4 Boot Menu................................................................................................................................ 47
3.5 Security Menu..........................................................................................................................48
3.6 Exit Menu..................................................................................................................................49
Appendix................................................................................................................................................. 38
Appendix 1：Watchdog Programming Guide........................................................................... 38
Appendix 2：IRQ and System Memory Map,1st MB Memory Map...................................... 40
Appendix 3：Glossary.................................................................................................................. 42

Chapter
One
Product
Introdu
ction

MITX-6110 User's Manual
1
Chapter 1 Product introduction
1.1 Product Specification
Size
●170mm×170mm（L×W）
Processor
●Pentium Silver J5005；
Pentium Silver N5000；
Celeron J4105；
Celeron J4005；
Celeron N4100；
Celeron N4000；
Display
●VGA：1xVGA port
●HDMI：1xHDMI* 2.0a port，Supporting resolution : 4096×2160@ 60 Hz
●LVDS：1xLVDS，dual channel，24bit
System Memory
●Support SO-DIMM DDR4 4/8GB up to 2400MT/s
Storage
●2x SATA,1x mSATA, support SATA Gen3: 6Gbps，Gen2: 3Gbps，Gen1: 1.5Gbps
●1x eMMC* 5.1（on board 16GB）
AUDIO
●On board ALC-662 sound card chip
●Support 1x line-in，1x mic，1xline out
LAN Function
●Network controller：Adopt 2xINTEL I211 chip

MITX-6110 User's Manual
2
●2xstandard RJ45 interfaces
●Speed：1000Mbps
●Support 3G/4G、WIFI expansion
USB Port
●Provide 8xUSB ports
●4xstandard USB 2.0 ports，4xstandard USB 3.0 ports
PCIE Port
●Provide 2xMINI PCIE port and 1x PCIE 1X port.
I/0 Functions
●Adopt F81804U chip
●2x COM，COM1 support RS23，COM2 support RS232/485
●1xPS2 KB/MS
●8xGPIO
●1x LPC expansion
●2x FAN
Power supply
●Single power supply：+12V/5A
BIOS
●128M bit SPI BIOS
Environment
●Operating Temperature：0℃～60℃
●Storage Temperature：-40℃～80℃
●Humidity：5% ~ 95% RH, non-condensing

Chapter
Two
Install
ation
Instruc
tion

MITX-6110 User's Manual
3
Chapter 2 Installation Instruction
2.1 Interface Location and Dimension Diagram
The following picture is the interface index for MITX-6110. When you install your devices,
please consult it and read the following guide. During installation please care for some devices.
Improper installation will lead to system malfunctions.
Note：During installation, in order to protect the parts of the board, please put
on anti-static gloves.
MITX-6110 Interface Location and Dimension Diagram
2.2 Installation Steps
Please refer to the following steps to install your computer：
1．Adjust all Jumpers on MITX-6110 according to the manual；

MITX-6110 User's Manual
4
2．Install CPU and memory；
3．Install other expansion cards；
4．Connect all the signal lines, cable, panel-control circuitry and power supply；
5．Start the computer，finish BIOS setup.
Key components of this motherboard are Integrated circuit, and these components
will be easily damaged by electrostatic influence. So, before installing the motherboard,
you should always keep the following precautions in mind：
1．Hold the board by the edges; don't touch any components or pins on the board.
2．Use an anti-static wrist strap or wear anti-static gloves while getting in touch with integrated
circuit components (such as CPU, RAM).
3．Place components in a grounded anti-static bag/pad when these components are
uninstalled.
4．Please make sure the power switch is disconnected before inserting the power plug.
2.3 Memory Installation
This motherboard is equipped with DDR4 slot. Please pay attention to the following two
points when installing memory bank：
1．When fixing, make sure the notch matches SO-DIMM socket and then insert memory bank
into the socket. Press it down to tight the connection.
2．Choose the proper memory bank that supports motherboard specification.
2.4 Jumper Setting
Please setup the jumpers accordingly before installing hardware devices.
Note: How to identify jumper and PIN1 of interface. Please observe the word mark of plug
socket, it will use “1”or bold line or triangular symbols; And please look at the back of PCB,
each weld spot has a square point, which is PIN 1; usually there is a white arrow beside PIN 1.
2.4.1 CMOS Content Clearance /Hold Setting（JCC1、JCC2）
CMOS powered by on board button battery. Clean CMOS will lead to a permanent
elimination of the previous system setting and back to the original (default setting) system
settings.
Steps：（1）Turn off the computer, disconnect the power supply；
（2）Use jumper cap short JCC Pin 1 and Pin 2 for 5~6 sec，Then restore the default

MITX-6110 User's Manual
5
setting of Pin 2 and Pin 3；
（3）Turn on the computer, then press DEL key into the BIOS setting and reload the
optimized defaults；
（4）Save and exit setting.
JCC：
Setting
JCC
1-2
Clear CMOS (BIOS renew to initialization)
2-3
Normal status(default)
Do not clear CMOS when power on, otherwise it will damage the motherboard!
JCC1、JCC2

MITX-6110 User's Manual
6
2.4.2 Hardware Switch for System Auto Boot upon Power On （JAT）
JAT：
Setting
JAT
Open
Disable Auto Boot
Close
Enable Auto Boot
JAT

MITX-6110 User's Manual
7
2.4.3 Debug Interface（DB_UART）
DB_UART：
2.4.4 COM2 Jumper Setting（J1，J2）
J1 ，J2 jumper are used to set the transmission mode of COM2 ，COM2 support
RS232/RS485 transmission mode，you can choose settings according to your own needs, the
default transmission mode is RS232.
PIN
SINGNAL NAME
1
UART2_TXD
2
GND
3
UART2_RXD
DB_UART

MITX-6110 User's Manual
8
J1、J2：
2.5 Interface Specification
When connecting external connectors, please read this manual carefully in order to
avoid damage to the motherboard!
2.5.1 SATA Port（SATA1、SATA2、JSATAPWR、MCU_DB）
Provide 2x7PIN SATA port，and 1x2.54mm 1X5PIN connector（SATA power supply）port，
1xMCU_DB port.
COM2 RS232（default）
COM2 RS485
J1
1-3 2-4
3-5 4-6
J2
1-2
3-4 5-6
J1、J2

MITX-6110 User's Manual
9
SATA1、SATA2：
PIN
SINGNAL NAME
1
GND
2
TX+
3
TX-
4
GND
5
RX-
6
RX+
7
GND
JSATAPWR：
PIN
SINGNAL NAME
1
+12V
2
GND
3
+5V
SATA2
JSATAPWR
SATA1
MCU_DB

MITX-6110 User's Manual
10
4
GND
5
+3.3V
MCU_DB：
PIN
SINGNAL NAME
1
NC
2
MCU_TXD
3
MCU_RXD
4
MCU_RST#
5
GND
2.5.2 Serial Ports （HDMI JCOM1、VGA JCOM2）
Provide 2xstandard COM ports，COM1 support RS232 model，COM2 support RS232/485
model.
JCOM1：
SINGNAL NAME
PIN
SINGNAL NAME
HDMI_COM2 JCOM1
VGA_COM2 JCOM2
JVGA

MITX-6110 User's Manual
11
HDCD#1
1
2
HDSR#1
HSIN1
3
4
HRTS#1
HSOUT1
5
6
HCTS#1
HDTR#1
7
8
HRI#1
GND
9
10
GND
JCOM2：
SINGNAL NAME
PIN
SINGNAL NAME
HDCD#2TX-DATA-
1
2
HDSR#2
HSIN2TX+DATA+
3
4
HRTS#2
HSOUT2
5
6
HCTS#2
HDTR#2
7
8
HRI#2
GND
9
10
GND
VGA_COM2：
PIN
SINGNAL NAME
1
DATA-
2
DATA+
3
HSOUT2
4
HDTR#2
5
GND
6
HDSR#2
7
HRTS#2
8
HCTS#2
9
HRI#2
COM1：
PIN
SINGNAL NAME
1
HDCD#1
2
HSIN1
3
HSOUT1
4
HDTR#1
5
GND

MITX-6110 User's Manual
12
6
HDSR#1
7
HRTS#1
8
HCTS#1
9
HRI#1
JVGA：
SINGNAL NAME
PIN
SINGNAL NAME
VGA1_R
1
2
GND
VGA1_G
3
4
VGA1_SDA_R
VGA1_B
5
6
VGA1_HSYNC
5V_DDC
7
8
VGA1_VSYNC
GND
9
10
VGA1_SCL_R
2.5.3 Display Port（LVDS）
Provide 1xdual channel LVDS port.
LVDS

MITX-6110 User's Manual
13
LVDS：
SINGNAL NAME
PIN
SINGNAL NAME
VDD_PANEL
1
2
VDD_PANEL
VDD_PANEL
3
4
L_BKLTEN_R
GND
5
6
GND
LVDSA_DATA0#
7
8
LVDSA_DATA0
LVDSA_DATA1#
9
10
LVDSA_DATA1
LVDSA_DATA2#
11
12
LVDSA_DATA2
GND
13
14
GND
LVDSA_CLK#
15
16
LVDSA_CLK
LVDSA_DATA3#
17
18
LVDSA_DATA3
LVDSB_DATA0#
19
20
LVDSB_DATA0
LVDSB_DATA1#
21
22
LVDSB_DATA1
LVDSB_DATA2#
23
24
LVDSB_DATA2
GND
25
26
GND
LVDSB_CLK#
27
28
LVDSB_CLK
LVDSB_DATA3#
29
30
LVDSB_DATA3