Oce TDS100 User manual

Océ TDS100
Quick reference guide
All manuals and user guides at all-guides.com
all-guides.com

Copyright
© 2005, Océ-Technologies B.V. Venlo, The Netherlands
All rights reserved. No part of this work may be reproduced, copied, adapted,
or transmitted in any form or by any means without written permission from
Océ.
Océ-Technologies B.V. makes no representation or warranties with respect to
the contents hereof and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose.
Further, Océ-Technologies B.V. reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation to
notify any person of such revision or changes.
Edition 2005-2
Océ-Technologies B.V.
GB
This manual is a part of a documentation set. The following table
displays the complete list.
Note: Visit Océ on the internet at www.oce.com for more
information.
Document Publication
medium Contents
Safety
manual Paper book ■Instructions for safe use.
■Safety data sheets.
Quick
reference
guide
Paper book ■A short description on how to operate the
Océ TDS100.
User manual CD-ROM ■A complete description on how tooperate
and maintain the Océ TDS100.
All manuals and user guides at all-guides.com

Contents 3
Contents
Chapter 1 About the Océ TDS100
The components 6
The operator panel 8
Make copies 11
Replace media rolls 12
Add toner 13
Clear jams 15
All manuals and user guides at all-guides.com

4 Quick reference guide
All manuals and user guides at all-guides.com

5
Océ TDS100
Quick reference guide
Chapter 1
About the Océ TDS100
All manuals and user guides at all-guides.com

6 Quick reference guide
The components
Nr. Component Function
1 On / off switch Turn on and off the Océ TDS100.
Note: The on / off switch is not visible in the
illustration.
2 Operator panel Set up, start and control the copy jobs.
3 Original feed table Feed the original.
4 Manual feed table Feed the media manually.
5 Roll 1 (drawer) Feed the media automatically from roll 1.
6 Roll 2 (door) Feed the media automatically from roll 2.
8
2
1
3
4
6
5
7
11
1
0
9
All manuals and user guides at all-guides.com
all-guides.com

About the Océ TDS100 7
Note: Some components may not be available on your Océ TDS100 due to the
differences between the configurations.
7 Integrated receiving
tray Receive the copies.
8 Top cover Give access to the transparent plate.
9 Fuser cover Give access to the fuser.
Note: The fuser is not visible in the
illustration.
10 Left cover Give access to the fill opening of the toner
reservoir, the waste toner bag and to the
handle of the fuser cover.
11 Middle cover Give access to the underside of the manual
feed table.
Nr. Component Function
All manuals and user guides at all-guides.com

8 Quick reference guide
The operator panel
4
2
0
-2
-4
media paper
roll 1
trailing
synchro
film
roll 2
leading
standard
feed
manual
strip
cut
toner media jam
6
8
1234 5
1413
1
0
1
2
7
9
1
1
All manuals and user guides at all-guides.com

About the Océ TDS100 9
The indicators
Nr. Indicator Function
1 'Toner' Indicate that the Océ TDS100 has run out of toner.
2 Green light Indicate that the copier is ready.
A blinking green light indicates that the copier runs a
copy job.
3 Red light Indicate that an error has occurred.
4'Media
jam'
■Indicate that the original or copy media has
jammed.
■Indicate that the media roll is empty for a 1 roll and
2 roll configuration.
■Indicate that you can remove the cut off strip
5Display■Display the media size when you change a roll.
■Display the strip length when you add or remove a
strip.
■Display a message code.
■Display the length of the original when you copy
manually on cut sheet media
All manuals and user guides at all-guides.com

10 Quick reference guide
The keys
Note: Some functions may not be available on your Océ TDS100 due to the
differences in the configurations.
Nr. Key Function
6 'Media' Select the media type.
7 'Feed' Select the media feed method.
8 Exposure Adjust the exposure.
Use the exposure setting to correct the background of
the copy.
9 'Strip' Select the edge for the strip.
■'Trailing'
Use the adjustment key to set the trailing strip length.
A positive value adds a strip, a negative value removes
a strip.
■'Leading'
Use the adjustment key to set the leading strip length.
A positive value adds a strip, a negative value removes
a strip.
10 Adjustment
key
■Adjust the strip length.
■Adjust the media size for a new roll.
■Adjust the media size for the standard cut size.
11 'Cut' Select the cut method.
■'Synchro' enables you to cut the copy to the same
size as the original.
■'Standard' enables you to cut the copy to the same
size as a standard size. Use the adjustment key to set
the standard size.
12 Copies Adjust the number of copies.
13 Stop ■When you press the stop key while the copier runs
a copy job, the copy job will stop.
■When you press the stop key once while you set up
a copy job, the number of copies returns to 1.
■When you press the stop key twice while you set up
a copy job, the default values return.
14 Start Start the copy job.
All manuals and user guides at all-guides.com