Oneida Air Systems XXS050333 User manual

Rev: 05/10/2021 Doc. #ZBM000104
Appearance may vary slightly
U.S. Patent: #8491685,
#8514090, #8496719,
#7247180
OWNER’S MANUAL
High Vacuum
Dust Collector
with SMART Boost
5 HP
# XXS050333

1oneida-air.com
Table of Contents
System Start-Up Information 2
System Specications 4
System Dimensions 5
System Contents 6
Assembly Instructions 8
Maintenance 20
Troubleshooting 21
F.A.Q. 22
Recommended Accessories 24
Warranty Information 26
Notes 27

2Oneida Air Systems
System Start-Up Information
1. Install ductwork completely before operating collector
a. Seal ductwork with silicone sealant or duct tape.
b. Have dust drum in place and sealed.
2. DO NOT operate Fan / Blower unless Fan Housing is attached to Cyclone body and Dust Drum is in place. Dust Drum and
Cyclone must be in place and sealed or motor will overheat!
3. DO NOT operate without lter in place. Fan blade can cause serious injury.
4. e Direct Drive Fan / Blower makes the system top heavy! Use extreme care when setting the unit up! It is recommended
that at least two people li the system up.
5. Check amperage draw on motor with all gates open. Current draw should not exceed maximum motor amperage as stated
on motor plate. (Oneida Air Systems is not responsible for damage to motors caused by improper installation, wiring or
failure to follow these directions).
6. is equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an
explosion.
7. To reduce the risk of Electric Shock, DO NOT use outdoors or on wet surfaces.
8. Exhaust air should not be vented into a wall, a ceiling, or a concealed space of a building.
9. To reduce the risk of injury from moving parts - unplug BEFORE servicing.
 WARNING 
 FIRE HAZARDS 
1. Wood shaping and cutting processes generate wood chips, shavings and dust. ese materials are considered combustible.
Air borne wood dust below 420 microns in size (0.17 of an inch) in certain concentration ranges when ignited can deagrate
(burn quickly). An ignition source such as a spark or ember can ignite a dust mixture resulting in an expanding ame
front, which can cause an explosion if tightly contained. A disturbance that raises a cloud of accumulated ne dust can raise
additional dust clouds, which can cause a series of explosions that can level an entire building. Until this type of re has been
witnessed, it is dicult to believe the devastation. is type of re is rare but worth safeguarding against.
2. e best way to avoid a wood shop re is to keep the shop clean. A shop ankle deep in dust with layers of ne dust
everywhere is an accident waiting to happen. A good dust collection system reduces overall re hazards but also adds new
concerns. A re hazard is still present. Combustible material is now in the dust collector and storage container.
3. e following points are worth heeding:
a. It is the buyer’s responsibility to follow all applicable federal, state, local, OSHA, NFPA, or authorities having jurisdiction
codes and regulations when installing and operating this dust collector.
b. Fire Marshals may want the unit located outside of the building. If the collector is located inside the facility, controls
such as spark detection, suppression, or explosion venting may be required.
c. Most local jurisdictions consult or adopt NFPA (National Fire Protection Agency) codes. However, other codes may
apply. Local codes may vary from jurisdiction to jurisdiction.
Make sure to read and understand the installation and maintenance instructions as well as all
recommended safety practices.


3oneida-air.com
System Start-Up Information (Continued)
d. NFPA664 Code book, “Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking
Facilities”, applies to woodworking operations that occupy areas of more than 5,000 sq. . or to areas where dust
producing equipment requires an aggregate dust collection ow rate of more than 1,500 cfm (cubic feet per minute).
is exempts some small operators from the NFPA code 664, but other codes may apply in your jurisdiction. Consult
your local Fire Marshal for help. Additional information can be found in NFPA Code Book 664.
4. e customer assumes the responsibility for contacting their insurance underwriter regarding specic application
requirements of explosion venting or if additional re protection and safety equipment may be required.
5. DO NOT use this product to collect other types of ammable dust or ammable vapors! - Fire or explosion may occur!
6. NEVER collect sparks from a bench grinder into a wood dust collector.
7. NEVER introduce sparks or sources of ignition into the dust collector.
8. Personnel should be kept at least 20 . away from unit.
9. Check dust bin frequently and before leaving the shop for smoldering material.
10. Keep portable re extinguishers handy.
a. e ABC type (dry chemical) is generally a good choice for small wood shops.
b. Additional information on portable extinguishers can be found in NFPA 10 (Standard for Portable Fire Extinguishers).
11. Be especially careful with sanding units. ey can produce concentrations of dust in the combustible range. Make certain
enough air volume is at the suction point to capture all the particulate generated.
12. is high air volume will dilute the mixture below the lower limit of ammability. Be careful not to generate sparks into the
sanding dust.
13. Empty dust bin and clean lter oen, especially when sanding.
14. DO NOT overload woodworking equipment, especially sanders. Excessive frictional heat can spontaneously ignite dust.
15. Sparks can be generated in several ways:
a. High speed sanders and abrasive planers may strike foreign material.
b. Saws and edgers may strike foreign material and create a red-hot metal fragment.
c. Knots in hardwood can create frictional sparks.
d. Trapped metal when drawn into the collector can spark against ductwork.
e. Check wood stock for old nails and screws which can create red hot metal fragments.
16. Avoid using excessively large wood waste bins.
17. ALWAYS check storage bins for smoldering material before leaving for the day.
18. Electrically ground all equipment and ducting. Static sparks can ignite wood dust. (Avoid using PVC drain pipe.)
19. DO NOT allow accumulation of layers of ne dust on horizontal surfaces (especially overhead lights, electrical boxes and
fuse panels which can ignite dust.)
20. UNPLUG UNIT BEFORE SERVICING OR CLEANING
Customer Service Dept.
1-866-387-8822 • [e-mail]

4Oneida Air Systems
System Specications
OPERATION
Fan Rating (with Cyclone & Filter) 1,789 Actual CFM at 5.4”S.P.
Maximum Suction Rating 23”WC
MOTOR AND ELECTRICAL
Motor Type U.S. Made TEFC Motor
Motor Insulation Class F
Motor Service Factor 1.15
Horsepower 5 HP
Motor Speed 3,500-4,500 RPM
Phase Single-Phase (1ph)
Voltage 208-230V
Cycle 60Hz
Listed FLA 12-11.8A
On/O Switch Remote Starter with Push button On/O Switch and RF Keyfob
Power Cord 10 ft
Power Connector Wire
Recommended Circuit Size 30A
Recommended Circuit Size HACR
Sound Emission 84-85 dBA @ 10 ft
IMPELLER
Size 15"
Material Single-piece, backward inclined, non-sparking/non-ferrous
CARTRIDGE FILTER
Filter Media Type Izumi Axtar Spunbond Media
Filter Eciency 99.9% @ 0.2-2.0 microns
Filter Surface Area 220 Sq. Ft.
SYSTEM DIMENSIONS AND CONSTRUCTION
Barrel/Cyclone Body Heavy-gauge cold-rolled steel
Inlet 7" Diameter
Overall Height (with 55 Gallon Drum) 106"

5oneida-air.com
106"
2,692 mm
18"
457 mm
48"
219 mm
87-1/2"
2,223 mm
30"
762 mm
36"
914 mm
68"
1,727 mm
78-1/2"
1,994 mm
37"
940 mm
8"
203 mm
27"
686 mm
30”
762 mm
Nominal dimensions shown with a 55 gallon drum. Dimensions subject to slight variations in manufacturing.
Top View
System Dimensions

6Oneida Air Systems
Please unpack the parts carefully and conrm you have
received each item listed here.
*Additional parts are included in your hardware
package.
ID Part number Part description Qty
A BXI050318C Motor Assembly 5 HP 3 PH 1
B BHX020005B Fan Housing 1
C SXI002108 Barrel 1
D SCX002109 Cone 1
E ACB120000 8-12" Hose Clamp 2
F DHF090001 9" x 1' Diameter Flex Hose 1
G SEX550900 Steel Drum Lid w/ 9" Collar 1
H SES550000 55 Gallon Steel Drum w/ Clamp 1
I DEF080099 8" Outlet Adapter 1
J DES900899 8" Plenum Elbow 1
K DWP877099 8x7x7 Pants Wye 1
L ACB080000 6-8" Hose Clamp 4
M DHF070000 7" Diameter Flex Hose 3'
N FPX020019 Dual Filter Plenum Plate 1
O AHX0021819 Filter Accessory Pack 1
O1 BSC180000 Drop-in Silencer 2
O2 AFT000001 5/16"-18 Thumb Nut 16
O3 AFW180000 5/16" Flat Washer 8
O4 AFJ051602 5/16"-18 x 2" J Bolt 16
O5* AHX186200A Filter Stacking Hardware Kit 2
O6 FPZ000018 Fine Dust Bin 2
O7 FPB210001 Dual Filter Adapter Bracket 2
O7A AFB155175 5/16-18" x 3/4" Hex Head Bolt 3
O7B AFW180000 5/16" Flat Washer 3
ID Part number Part description Qty
O7C AFT155175 5/16 Whiz Lock Nut 3
P FCS183900 18" x 39" Filter 2
Q AHX001800 Hardware Kit 1
Q1 RGZ025050 Poron Gasket Roll 29'
Q2 QCZ080000 8" Duct Clamp 2
Q3 AFB155155 5/16"-18 x 1" Flange Bolt 15
Q4 AFW180000 5/16" Flat Washer 39
Q5* AFS015700 3/8-16" x 1-1/4" Hex Head Bolt 3
Q6* AFW190000 3/8" Flat Washer 20
Q7* AFT000004 3/8” Whiz-Lock Nut 10
Q8 AFB155190 5/16-18" x 1" Hex Head Bolt 12
Q9 AFT155175 5/16-18” Whiz-Lock Nut 12
Q10* AFS015100 3/8-16" x 1" Hex Head Bolt 7
Q11 FGA000002 14" Grounding Cable with Two
8-18 x 3/8” Self-tapping Screws 1
R STZ212300 Stand 1
S STZ212301 Stand Extensions 1
T AXB999110B Dust Sentry 1
If you cannot find an item on the list examine the packaging materials very carefully. Certain
components may have been pre-installed for shipping purposes. There may be hardware
leftover.
System Contents

You will need the following tools:
GENERAL FAN HOUSING FILTER
8' Ladder Razor Knife Flathead Screwdriver 7/16" Wrench
Level Diagonal Cutters Hammer 7/16" Socket Wrench
Scissors Tape Measure / Ruler
1/2" Wrench 1/4" Socket
1/2" Socket Wrench Impact Driver

7oneida-air.com
× 8
× 8
× 7
× 7
× 8
× 6
× 6
× 6
× 12
× 12
× 8
× 8
× 8
× 8
× 4
× 4
× 4
× 24
System Contents (Continued)
A
T
R
S
B
D
H
I
J
G
EF
C
Q11
O7A
O7B
O7C
Q3
Q3
Q4
Q4
Q4
Q6
Q9
Q7
Q8
Q10
Q2
K
LM
O1
O6
O4
O4
O7
O3
O2
O2
N
P
Q1 Note: Sent
out attached
to the Motor
Assembly (A)

8Oneida Air Systems
Before you start, determine which direction you want your filter to hang and which direction
you want your duct work to enter the collector. The fan housing and cyclone barrel bolt holes
are drilled at 45 degree increments; Some orientations are not possible.
Assembly Instructions
Tip: e collector will seem quieter if the outlet is aimed away from the area where people tend to work.
Filter will
obstruct
inlet pipe
INLET
INLET
INLET
INLET
INLET
INLET
INLET
INLET
INLET
INCORRECTCORRECT CORRECT

FIG. 1
1 Assemble the Stand (R) and Stand Extensions
(S) [FIG 1]. Refer to the instruction sheets
included:
• Stand Instruction Sheet
# ZBI000014
• Leg Extension Instruction Sheet
# ZBI000013