ORiNG IPS-1080A User manual

P1 P2 Fault
IPS-1080A
3
4
10/100TX
1
2
7
8
5
6
Practical Operation
QIG Quick Installation Guide
IPS-1080A
IPS-1080A
Version 1.0
Quick Installation Guide
ORing Industrial Networking Corp.
Features
IPS-1080A
IPS-1080A
IPS-1080A
is slim type unmanaged PoE Ethernet switch with P.S.E. function.
supports Power over Ethernet, a system to transmit electrical power,
along with data, to remote devices over standard twisted-pair cable in an Ethernet
network. switch has 8X10/100Base-T(X) P.S.E. (Power Sourcing
Equipment) ports. P.S.E. is a device (switch or hub for instance) that will provide
power in a PoE setup. The wide operating temperature range from -40 C to 70 C
can satisfy most of operating environment. Therefore, the switch is one of the most
reliable choices for PoE Ethernet application.
oo
Introduction Specifications
IPS-1080A can be used in connecting several Ethernet devices like Ethernet I/O, IP-
Camera or other Ethernet switches. In addition, there are two r power
inputs at terminal block to avoid interruption caused by power down. When the
primary DC power input fails, the backup power input will take over immediately to
guarantee a non-stop operation.
edundant
Industrial Unmanaged PoE Switch
Provide 8x10/100Base-T(X) PoE (P.S.E.) ports
Supports IEEE 802.3at compliant PoE and total power budget is 120Watts with
maximum 30Watts per port
Support auto-negotiation and auto-MDI/MDI-X
Support store and forward transmission
Support flow control
Support surge protection technology
Warning system by relay output
Slim type rigid IP-30 housing design
DIN-Rail and wall mounting enabled
Power Connection Guide
Frame Ground
PWR-1PWR-2
V2-V2+ V1-V1+
G
1A@24V DC 50-57V
Power
Supply
50 VDC
V+
V-
Warning
Device
GND+24V
V+
V-
DIP Switch Select for
Power Alarm Relay Output
Power
Supply
50 VDC
Power
Supply
DIP-2
OFF
OFF
ON
DIP-1
Power failure relay alarm disabled
PWR-1 failure, alarm enabledrelay
PWR-2 failure, alarm enabledrelay
DIP Switch Function
OFF
ON
OFF
Description
Front Panel
A
ON PWR-1 or PWR-2 failure,
alarm enabledrelay
ON
1907-2-29-IPS1080A-0
Connections of Ethernet devices
PRINTED ON RECYCLED PAPER
ORing Switch Model
Physical Ports
Technology
Ethernet Standards
LED Indicators
Green: Power LED x2Power indicator
10/100 Base-T(X) Ports in RJ45
Auto MDI/MDIX with P.S.E. 8
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX
IEEE 802.3x for Flow control
IEEE 802.3at PoE specification (up to 30 Watts per port for P.S.E.)
MAC Table 2048 MAC addresses
Environmental
-40to85C(-40to185 F)
oo
Storage Temperature
Operating Temperature
5% to 95% Non-condensingOperating Humidity
Regulatory Approvals
-40to70C(-40to158 F)
oo
Amber:IndicatePWR1orPWR2failure
Fault indicator
Fault Contact
Relay Relay output to carry capacity of 1A at 24 VDC
Power
Redundant Input power
Power consumption(Typ.) 4.5 Watts (power consumption of P.S.E. is not included)
Overload current protection
Reverse polarity protection
Present
Not Present
Physical Characteristic
Enclosure IP-30
Dimension(WxDxH)
Weight (g) 395g
Dual DC inputs 50-57VDC on 6-pin terminal block
26.1(W)x94.9(D)x144.3(H)mm(1.03x3.74x5.68inches)
10/100Base-T(X)RJ45 Port
Indicator
Green for port Link/Act.
Green for PoE power injected.
Processing Store-and-Forward
Green: PoE power injected
Green: Link/Act
LAN Port
Power 1 LED Power Fault LED
SWITCH
INDUSTRIAL
PoE
Power 2 LED
IPS-1080A
FCC Part 15, CISPR (EN55022) class AEMI
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge),
EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
EMS
IEC60068-2-27Shock
IEC60068-2-32
IEC60068-2-6Vibration
Free Fall
Warranty
5 years
EN60950-1Safety

QIG Quick Installation Guide
PRINTED ON RECYCLED PAPER
Accessory Communication Connections
RJ45 (8-pin) to RJ45 (8-Pin) Straight-Through Cable Wiring
RJ45 Plug Pin1
Straight-Through Cable
Switch Port
RJ-45
Connector
Tx+
Tx-
Rx+
Rx-
3
6
1
2
NIC Port
RJ-45
Connector
Rx+
Rx-
Tx+
Tx-
3
6
1
2
RJ45 (8-pin) to RJ45 (8-Pin) Cross-Over Cable Wiring
RJ45 Plug Pin1
Cross-Over Cable
Switch Port
(NIC Port)
RJ-45
Connector
Tx+
Tx-
Rx+
Rx-
3
6
1
2
RJ-45
Connector
Rx+
Rx-
Tx+
Tx-
1
2
3
6
Switch Port
(NIC Port)
(Rx+)
(Rx-)
(Tx+)
(Tx-)
(Tx+)
(Tx-)
(Rx+)
(Rx-)
Version 1.0
Quick Installation Guide
ORing Industrial Networking Corp.
Installation
DIN-Rail Install Step Wall-mounted Install Step 10/100Base-T(X) Ethernet Connection
Dust Cover (RJ-45)
2
QIG
6
Round Screw (M3 X3)
3Wall-mounted kit (for Slim Type)
4
25mm DIN-Rail kit
5
6-Pin Terminal block
1
I1X1, 2X8, 3X8,
X1
X2,
A
IPS-1080A
Model name Model Description Accessory
Front Panel
Industrial 8-port slim type unmanaged PoE
Ethernet switch with 8x10/100Base-T(X)
P.S.E. 6
4
5X1,
Packing list
Pin Definition
10/100Base-T(X) PoE P.S.E. Port
RJ45 Pin Definition
Pin No.
TD+ with PoE Power input +
#1
Description
#2
#3
#6
TD-withPoEPowerinput+
RD+ with PoE Power input -
RD- with PoE Power input -
Industrial Unmanaged PoE Switch
SWITCH
INDUSTRIAL
PoE
IPS-1080A
IPS-1080A
ORing Industrial Networking Corp.
Copyright© 2013 ORing
All rights reserved.
TEL: [phone]
FAX: [phone]
Website: www.oring-networking.com
E-mail: [email protected]