Panasonic KX-TG1611FX User manual

PNQW2526ZA TT0211MU0 (A)
FX-2/2
Contents/Contents/Contents/
Contents/Contents/Contents/Contents
Page/Page/Page/
Page/Page/Page/Page
Croatian instructions 2 - 8
Slovene instructions 9 - 15
Romanian instructions 16 - 22
Bulgarian instructions 23 - 29
Serbian instructions 30 - 36
Macedonian instructions 37 - 43
Bosnian instructions 44 - 50
KX-TG1611FX
KX-TG1612FX
KX-TG1613FX
KX-TG1711FX
KX-TG1712FX
Quick Guide/Quick Guide/Quick Guide/
Quick Guide/Quick Guide/Quick Guide/
Quick Guide
Model No./Model No./Model No./
Model No./Model No./Model No./
Model No.
TG161x_171xFX(e)for_7 language_QG.book Page 1 Monday, February 7, 2011 2:50 PM

2
Connections
Important:
L First plug in the supplied telephone line cord and then plug in the AC adaptor cord. (KX-TG1611/
KX-TG1612/KX-TG1613)
L If you use a telephone line cord which is not supplied, the unit may not work properly.
*DSL/ADSL filter (not supplied) is required if you have DSL/ADSL service.
*DSL/ADSL filter (not supplied) is required if you have DSL/ADSL service.
To telephone line
DSL/ADSL filter*
Hook Press plug
firmly.
(220-240 V AC, 50/60 Hz)
Use only the supplied
Panasonic AC adaptor.
Use only the supplied
telephone line cord.
“Click”
Correct
Wrong
“Click”
KX-TG1611/KX-TG1612/KX-TG1613
Base unit
Hooks
Press plug firmly.
Correct
Wrong
KX-TG1711/KX-TG1712
To telephone line
DSL/ADSL filter* “Click”
(220-240 V AC, 50/60 Hz)
“Click”
Use only the supplied
telephone line cord.
Use only the supplied
Panasonic AC adaptor.
Model No. KX-TG1611FX/KX-TG1612FX/KX-TG1613FX
KX-TG1711FX/KX-TG1712FX
Quick Guide
Bosnian
TG161x_171xFX(e)for_7 language_QG.book Page 2 Monday, February 7, 2011 2:50 PM

3
Connections
Battery installation/Battery charging
Charge for about 7 hours.
Note:
L USE ONLY Ni-MH batteries AAA (R03) size.
L Do NOT use Alkaline/Manganese/Ni-Cd batteries.
Operating tips
Navigator key
− {^} , {V} , { < } , or { > } : Scroll through various lists and
items.
− ? (Volume: {^} or {V} ): Adjust the receiver volume
while talking.
− { < } ( y : Caller list): View the caller list.
− { > } ( R : Redial): View the redial list.
Charger
(220-240 V AC, 50/60 Hz)
Press plug firmly.
Use only the supplied Panasonic AC adaptor.
Hooks
Rechargeable Ni-MH ONLY
{V}
{^}
{<}{>}
Volume up
Volume down
TG161x_171xFX(e)for_7 language_QG.book Page 3 Monday, February 7, 2011 2:50 PM

4
Display language (Handset) (default: “ English ” (English))
16 display languages are available.
L If you select a language you cannot read:
{i c } s {j /OK } s {V} 4 times s {j /OK } 2 times s { r } : Select your desired language. s
{j /OK } s {i c }
Date and time (Handset)
1 {j /OK }
2 { r } : “ Set Time ” (Set time) s {j /OK }
3 { r } : “ Date & Time ” (Date and time) s {j /OK }
4 Enter the current date, month, and year. s {j /OK }
5 Enter the current hour and minute. s {j /OK }
6 {i c }
Dialling mode (Handset) (default: “ Tone ” (Tone))
1 {j /OK }
2 { r } : “ Setup ” (Setup) s {j /OK }
3 { r } : “ Dial Mode ” (Dial mode) s {j /OK }
4 { r } : Select the desired setting.
5 {j /OK } s {i c }
Basic operations
Making/Answering calls (Handset)
Making calls Dial the phone number. i {C}
Answering calls {C}
To hang up {i c }
To adjust the receiver volume Press {^} or {V} repeatedly while talking.
Making a call using the redial list { > } ( R ) s { r } : Select the desired phone number. s {C}
Temporary tone dialling
(for rotary/pulse service users)
Press * before entering access numbers which require tone
dialling.
You can select
or
TG161x_171xFX(e)for_7 language_QG.book Page 4 Monday, February 7, 2011 2:50 PM

5
Making/Answering calls (Handset)
Handset ringer volume 1 {j /OK }
2 { r } : “ Ringer Setup ” (Ringer setup) s {j /OK }
3 { r } : “ Volume ” (Volume) s {j /OK }
4 { r } : Select the desired volume.
5 {j /OK } s {i c }
Phonebook (Handset)
Adding entries 1 {k}
2 { r } : “ New Entry ” (New entry) s {j /OK }
3 Enter the party’s name (12 characters max.). s {j /OK }
L
You can change the character entry mode by pressing
{k} .
L To enter a name, see the character table in the operating
instructions.
4 Enter the party’s phone number (24 digits max.). s {j /OK }
2 times
5 {i c }
Making calls 1 {k}
2 { r } : “ Show List ” (Show list) s {j /OK }
3 { r } : Select the desired entry.
L To view the phone number, press {j /OK } . s { r } : “ Phone
No.
” (Phone number) s {j /OK }
4 {C}
Frequently asked questions
Question Cause/solution
Why is w flashing? L The handset is too far from the base unit. Move closer.
L The base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
L The handset is not registered to the base unit. Register it
(page 7).
Why can I not make calls? L The dialling mode may be set incorrectly. Change the setting
(page 4).
What should I do when the handset
does not turn on?
L Make sure the batteries are installed correctly.
L Fully charge the batteries.
L Clean the charge contacts and charge again.
Basic operations
TG161x_171xFX(e)for_7 language_QG.book Page 5 Monday, February 7, 2011 2:50 PM

6
How long is the battery operating
time?
L When you are using fully-charged Ni-MH batteries (supplied
batteries);
In continuous use: 15 hours max.
Not in use (standby): 170 hours max.
L It is normal for batteries not to reach full capacity at the initial
charge. Maximum battery performance is reached after a few
complete cycles of charge/discharge (use).
L Actual battery performance depends on usage and ambient
environment.
Can I keep the handset on the base
unit or charger when I am not using
it?
L Even after the batteries are fully charged, the handset can be
left on the base unit or charger without any ill effect on the
batteries.
When should I replace the batteries? L If the batteries are fully charged until 5 is displayed, but
7 is displayed after a few calls, replace the batteries with
new ones.
What is a PIN? L The PIN is a 4-digit number that must be entered in order to
change certain base unit settings. The default PIN is
“ 0000 ” .
What should I do to display caller
information?
L You must subscribe to a Caller ID service. Contact your service
provider/telephone company for details.
What should I do when noise is
heard, sound cuts in and out?
L You are using the handset or base unit in an area with high
electrical interference. Re-position the base unit and use the
handset away from sources of interference.
L Move closer to the base unit.
L If you use a DSL/ADSL service, we recommend connecting a
DSL/ADSL filter between the base unit and the telephone line
jack. Contact your DSL/ADSL provider for details.
L Unplug the base unit’s AC adaptor to reset the unit and turn off
the handset. Reconnect the adaptor, turn on the handset and
try again.
What should I do when the operating
time seems to be shorter even after I
fully charged the batteries?
L Clean the battery ends ( S , T ) and the charge contacts with a
dry cloth and charge again.
Frequently asked questions
Question Cause/solution
TG161x_171xFX(e)for_7 language_QG.book Page 6 Monday, February 7, 2011 2:50 PM

7
Registering a handset to the base unit
The supplied handset and base unit are pre-registered. If for some reason the handset is not registered to
the base unit, re-register the handset.
1 {j /OK }
2 { r } : “ Setup ” (Setup) s {j /OK }
3 { r } : “ Register HS ” (Register handset) s {j /OK }
Press and hold {x} for about 5 seconds.
(No registration tone)
Wait until “ PIN:____ ” (PIN:____) is displayed. s
Enter the base unit PIN (default:
“ 0000 ” ). s
{j /OK }
L The next step must be completed within 90 seconds.
Wait until a long beep is heard and then enter the desired handset number you want to register.
L When the handset has been registered successfully, w stops flashing.
Handset
{j/OK}
Base unit
KX-TG1611/KX-TG1612/KX-TG1613
{x}
Handset
{j/OK}
Handset
TG161x_171xFX(e)for_7 language_QG.book Page 7 Monday, February 7, 2011 2:50 PM

8
Optional service (Caller ID)
If you subscribe to a Caller ID service,
caller information will be displayed when a call is received, or when viewing missed
calls.
012345
TG161x_171xFX(e)for_7 language_QG.book Page 8 Monday, February 7, 2011 2:50 PM

9
Declaration of conformity form/Declaration of conformity form/
Declaration of conformity form
The object of the declaration described above <A> is in conformity with the requirements of the following EU
legislations <B> and harmonized standards <C>.
The object of the declaration described above <A> is in conformity with the requirements of the following EU
legislations <B> and harmonized standards <C>.
The object of the declaration described above <A> is in conformity with the requirements of the following EU
legislations <B> and harmonized standards <C>.
TG161x_171xFX(e)for_7 language_QG.book Page 9 Monday, February 7, 2011 2:50 PM