Panasonic KX-TGC310UE User manual

Model No. KX-TGC310UE
KX-TGC313UE
KX-TGC320UE
Connections
Quick Guide
1
2
3
4
4
5
Base unit
1 Connect the AC adaptor to the unit by pressing the plug rmly.
2Fasten the cord by hooking it.
3Connect the AC adaptor to the power outlet.
4Connect the telephone line cord to the unit, then to the telephone line jack until you hear a
click.
5 A DSL/ADSL lter (not supplied) is required if you have a DSL/ADSL service.
Note:
L Use only the supplied Panasonic AC adaptor PNLV226E.
L Use only the supplied telephone line cord.
PNQW4421ZA TT0315MU0

– 2 – (2)
Connections
Charger
1Connect the AC adaptor plug to the unit until you hear a click.
2Connect the AC adaptor to the power outlet.
Note:
L Use only the supplied Panasonic AC adaptor PNLV233E.
2
1
Battery installation/Battery charging
Charge for about 7 hours.
12
Note:
L USE ONLY rechargeable Ni-MH batteries AAA (R03) size (
1
).
L Do NOT use alkaline/manganese/Ni-Cd batteries.
L Follow the directions on the display to set up the unit.
L Conrm “Charging” (Charging) is displayed (
2
).
Base unit Charger

– 3 – (3)
Operating tips
Soft keys
By pressing a soft key, you can select the
feature shown directly above it on the display.
Navigator key
Symbol Meaning
{v} {^} Up
{y}{V} Down
{k} {<} Left
{R} {>} Right
−{^}, {V}, {<}, or {>}: Scroll through various
lists and items.
−{^} or {V} (v): Adjust the receiver or speaker
volume while talking.
−{y} (Caller list): View the caller list.
−{k} (Phonebook): View the phonebook
entry.
−{R} (Redial): View the redial list.
{V}
{^}
{
<}{>}
Display language (Handset) (default: “English” (English))
1{B}(11)
2{r}: Select your desired language. s{OK}s{m}
Date and time (Handset)
1{B}(1)1
2Enter the current date, month, and year. s{OK}
3Enter the current hour and minute.
4{OK}s{m}
Dialling mode (Handset) (default: “Tone” (Tone))
1{B}(12)
2{r}: Select the desired setting. s{OK}s{m}

– 4 – (4)
Phonebook (Handset)
Adding entries 1{k} s{B}
2{r}: “New Entry” (New entry) s{OK}
3Enter the party’s name. s{OK}
•You can change the character entry mode by pressing
{R/ECO}.
•To enter a name, see the character table in the
operating instructions.
4Enter the party’s phone number. s{OK} 2 times
s{m}
Making calls 1{k}
2{r}: Select the desired entry.
3{C}
Basic operations
Making/Answering calls (Handset)
Making calls Dial the phone number. s{C}/{s}
Answering calls {C}/{s}
To hang up {m}
To adjust the receiver/
speaker volume
Press {^} or {V} repeatedly while talking.
Making a call using the redial list {R} s{r}: Select the desired phone number. s{C}
Temporary tone dialling
(for rotary/pulse service users)
Press * before entering access numbers which require
tone dialling.
Handset ringer volume Press {^} or {V} repeatedly to select the desired volume
while ringing.

– 5 – (5)
Frequently asked questions
Question Cause/solution
Why is _displayed? L The handset is too far from the base unit. Move closer.
L The base unit’s AC adaptor is not properly connected.
Reconnect AC adaptor to the base unit.
L The handset is not registered to the base unit. Register it
(page 6).
Why can I not make calls? L The dialling mode may be set incorrectly. Change the
setting (page 3).
What should I do when the
handset does not turn on?
L Make sure the batteries are installed correctly.
L Fully charge the batteries.
L Clean the charge contacts and charge again.
How long is the battery operating
time?
L When you are using fully-charged Ni-MH batteries
(supplied batteries);
In continuous use: 16 hours max.
Not in use (standby): 200 hours max.
L Actual battery performance depends on usage and
ambient environment.
When should I replace the
batteries?
L If the batteries are fully charged until &is displayed, but
) is displayed after a few calls, replace the batteries with
new ones.
What is a PIN? L The PIN is a 4-digit number that must be entered in order
to change certain base unit settings. The default PIN is
“0000”.
What should I do to display caller
information?
L You must subscribe to a Caller ID service. Contact your
service provider/telephone company for details.
L The message “You must rst subscribe to
Caller ID.”(You must rst subscribe to Caller ID.)
will be displayed until you receive caller information after
subscribing to a Caller ID service.
What should I do when noise is
heard, sound cuts in and out?
L You are using the handset or base unit in an area with high
electrical interference. Re-position the base unit and use
the handset away from sources of interference.
L Move closer to the base unit.
L If you use a DSL/ADSL service, we recommend
connecting a DSL/ADSL lter between the base unit and
the telephone line jack. Contact your DSL/ADSL provider
for details.

– 6 – (6)
Registering a handset to the base unit
The supplied handset and base unit are pre-registered. If for some reason the handset is not
registered to the base unit, re-register the handset.
1Handset:
{B}(13)
2Base unit:
Press and hold {x} for about 5 seconds.
3Handset:
{OK}sWait until “Base PIN” (Base PIN) is displayed. sEnter the base unit PIN
(default: “0000”). s{OK}
Optional service (Caller ID)
If you subscribe to a Caller ID service,
012345
caller information will be displayed when a call is received, or when viewing
missed calls.