Parker TFP Series User manual

Bulletin MSG11-5715-734/UK
2-Way Servo
Proportional Valves with
VCD®-Technology
Operation Manual
Series TFP
Design ≥ 12
Parker Hannin
Manufacturing Germany GmbH & Co. KG
Industrial Systems Division Europe
Gutenbergstr. 38
41564 Kaarst, Germany
E-mail: [email protected].com
Copyright © 2022, Parker Hannin Corp.

2Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DE-
SCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND
PROPERTY DAMAGE.
This document and other information from Parker-Hannin Corporation, its subsidiaries and
authorized distributors provide product or system options for further investigation by users having
technical expertise.
The user, through its own analysis and testing, is solely responsible for making the nal selection
of the system and components and assuring that all performance, endurance, maintenance,
safety and warning requirements of the application are met. The user must analyze all aspects
of the application, follow applicable industry standards, and follow the information concerning
the product in the current product catalog and in any other materials provided from Parker or its
subsidiaries or authorized distributors.
To the extent that Parker or its subsidiaries or authorized distributors provide component or
system options based upon data or specications provided by the user, the user is responsible for
determining that such data and specications are suitable and su󰀩cient for all applications and
reasonably foreseeable uses of the components or systems.
WARNING — USER RESPONSIBILITY

3Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Content Page
1. Introduction 4
Characteristics of Valve Driver 4
Order Code TFP 5
Technical Data 6
Block Diagram of Integral Electronics 7
2. Safety Instructions 8
Symbols 8
Service 8
3. Important Details 8
Intended Usage 8
Common Instructions 8
Liability 8
Storage 8
4. Mounting / Installation 8
Scope of Supply 8
Available Bolts Kits 9
Mounting 9
Disassembly 9
Limits of Use 10
Pressure Fluids 10
Electrical Connection 10
Electrical Interfacing 11
5. Operation Instructions 13
Solenoid Current Monitoring 13
ProPxD Parameterizing Software 13
Air Bleeding of Hydraulic System 15
Filter 15
Flushing 15
6. Troubleshooting 15
7. Accessories / Spare Parts 16
Accessories 16
Spare Parts 16

4Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
1. Introduction
Parker 2-way servo proportional valves with VCD®
technology have an integrated electronics and re-
quire only one sole electrical common for the control
system. Di󰀨erent ow sizes are available to achieve
an optimal adaption for di󰀨erent applications.
Characteristics of Valve Driver
The described integral electronic driver combines all
necessary functions for the optimal operation of the
valves. Thanks to its excellent dynamic the valves
are usable within closed loop control applications.
The most important features are:
• high dynamic actuator principle with special
designed electronic driver
• closed loop controlled spool position
• constant current actuator control with overcur-
rent shuto󰀨
• excellent properties for response sensitivity and
temperature drift
• di󰀨erential input stage with various command
signal options
• diagnostic output for spool stroke
• standard central connection
• compatible to the relevant European EMC-
standards
B
A
XY
TFP050

5Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Ordering Code
2-way servo
proportional
valve with
LVDT
Pilot oil
Seal
Design
series
(not
required for
ordering)
Nominal
size
Standard
electronics
Command
signal
Flow
characteristic
linear
Code Supply Drain
2 External External
8
Plate with pipe
connections X1 (00)
and Y1 (99)
Note : Please order connector separately
1) HFC uids suitable.
2) For DFplus pilot valve with EtherCAT interface see installation
manual MSG11-5715-708/UK, "Supplement for Valves with
EtherCAT Interface".
TFP A 9 H C 0
Code Seal
N 1) NBR
V FPM
Code Nominal size
025 NG25
032 NG32
040 NG40
050 NG50
063 NG63
080 NG80
100 NG100
Code Command signal
B 0...+10 V
E 0...+20 mA
S 4...+20 mA
N 2) EtherCAT

6Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Technical Data
1) If valves with onboard electronics are used in safety-related parts
of control systems, in case the safety function is requested, the
valve electronics voltage supply is to be switched o󰀨 by a suitable
switching element with su󰀩cient reliability.
General
Design
Proportional throttle valve with LVDT and integrated electronics, slip-in
cartridge according to ISO 7368
Nominal size DIN NG25 NG32 NG40 NG50 NG63 NG80 NG100
Mounting position unrestricted
Ambient temperature [°C] -20...+50
Weight [kg] 9 11 21 28 42 77 122
Vibration resistance [g] 10 sinus 5...2000 Hz acc. IEC 68-2-6
10 (RMS) random noise 20...2000 Hz acc. IEC 68-2-36
15 shock acc. IEC 68-2-27
Hydraulic
Max. operating pressure [bar] Ports A, B, SP max. 420, X max. 350; XX observe accumulator
pressure rating; port Y max. 35
Fluid Hydraulic oil according to DIN 51524
Fluid temperature [°C] -20...+60 (NBR: -25...+60)
Viscosity, recommended [cSt]/
permitted [cSt]/
[mm²/s]
[mm²/s]
30 ... 80
20 ... 400
Filtration
Nominal ow at ∆p = 5 bar (linear) [l/min] 650 1200 1800 3100 5200 7600 11100
Max. ow (v = 30 m/s),
recommended (linear) [l/min] 1400 2600 4100 6200 9800 17000 25000
Flow direction B to A / A to B
Pilot pressure [bar] max. 350
Pilot oil Supply external via X
Drain external via Y
Leakage in pilot valve at 100 bar [ml/min] < 400
Pilot valve size NG06 NG10
Max. pilot ow at 140 bar pilot pressure [l/min] 21 33 37 54 71 86 105
Pilot pressure, recommended Pilot pressure px= system pressure ps
Minimum pilot pressure pmin
1) [bar] 140
Static/dynamic
(for optimal dynamics see installation recommendation)
Step response at pilot press. >140 bar [ms] 11 14 17 18 23 28 32
Frequency response at
pilot pressure >140 bar [Hz] on request
Hysteresis [%] < 0.1
Sensitivity [%] < 0.05
Temperature drift [%/K] < 0.025
Installation recommendations
The maximum pilot ow is given in the technical data.
At insu󰀩cient pilot oil supply – e.g. because of long
distances and/or small diameters – an accumula-
tor can be connected to port XX.
To avoid this, an accumulator can be connected to
port XX at the valve body of the TFP (not for nomi-
nal size NG25). A short-term undersupply with pi-
lot oil can be compensated via this accumulator.
The required accumulator size is dependent on the
pilot oil pressure.
Please also consider the Parker accumulator product
range and the Parker Accumulator Sizing Software.
Nominal
size
Required accumulator volume [l]
1 stroke
(close)
2 stroke
(close and open)
NG25 0.005 0.010
NG32 0.008 0.016
NG40 0.010 0.020
NG50 0.015 0.03
NG63 0.02 0.04
NG80 0.035 0.07
NG100 0.05 0.1

7Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Block Diagram of Integrated Electronics
Electrical
Duty ratio [%] 100
Protection class IP65 in acc. with EN 60529 (with correctly mounted plug-in connector)
Supply voltage / ripple [V] 22...30, electric shut-o󰀨 at <19, ripple < 5 % e󰀨., surge free
Current consumption max. [A] 3.5
Pre-fusing [A] 4.0 medium lag
Input signal
Code B Voltage [V] 0...+10, ripple < 0.01 % e󰀨., surge free
Impedance [kOhm] 100
Code E Current [mA] 0...+20, ripple < 0.01 % e󰀨., surge free
Impedance [Ohm] < 250
Code S Current [mA] 4...20, ripple < 0.01 % e󰀨., surge free
< 3.6 mA = enable o󰀨 > 3.8 mA = enable on according to NAMUR NE43
Impedance [Ohm] < 250
Di󰀨erential input max. [V] 30 for terminal D and E against PE (terminal G)
11 for terminal D and E against 0V (terminal B)
Enable signal [V] 5...30, Ri = > 8 kOhm
Diagnostic signal [V] 0...+10 / +12.5 error detection, rated max. 5 mA
EMC EN 61000-6-2, EN 61000-6-4
Electrical connection 6 + PE acc. EN 175201-804
Wiring min. [mm²] 7 x 1.0 (AWG16) overall braid shield
Wiring lenght max. [m] 50
1) Do not connect with the supply voltage zero.
Technical Data

8Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Liability
The manufacturer does not assume liability for
damage due to the following failures:
• incorrect mounting / installation
• improper handling
• lack of maintenance
• operation outside the specications
Do not disassemble the valve! In case of
suspicion for a defect please contact Parker.
Storage
In case of temporary storage the valve must be
protected against contamination, atmospheric ex-
posure and mechanical damages. Each valve has
been factory tested with hydraulic oil, resulting in
protection of the core parts against corrosion. Yet
this protection is only ensured under the following
conditions:
Outdoor storage or within sea and tropical
climate will lead to corrosion and might dis-
able the valve!
2. Safety Instructions
Please read the operation manual before instal-
lation, startup, service, repair or stocking! Paying
no attention may result in damaging the valve or
incorporated system parts.
Symbols
This manual uses symbols which have to be fol-
lowed accordingly:
Instructions with regard to the warranty
Instructions with regard to possible
damaging of the valve or linked system
components
Helpful additional instructions
Service
Workings in the area of installation, commissioning,
maintenance and repair of the valve may only be
allowed by qualied personnel. This means persons
which have, because of education, experience and
instruction, su󰀩cient knowledge on relevant direc-
tives and approved technical rules.
3. Important Details
Intended Usage
This operation manual is valid for 2-way high-
response valves series TFP. Any di󰀨erent or
beyond it usage is deemed to be as not intended.
The manufacturer is not liable for warranty claims
resulting from this.
Common Instructions
We reserve the right for technical modications of
the described product. Illustrations and drawings
within this manual are simplied representations.
Due to further development, improvement and
modication of the product the illustrations might
not match precisely with the described valve. The
technical specications and dimensions are not
binding. No claim may resulting out of it. Copyrights
are reserved.
Storage
period Storage requirements
12 months constant humidity < 60 % as well
as constant temperature < 25 °C
6 months varying humidity as well as vary-
ing temperature < 35 °C
4. Mounting / Installation
Scope of Supply
Please check immediately after receiving the valve,
if the content is matching with the specied scope
of supply. The delivery includes:
• valve
• operation manual
The central connector has to be ordered separately
and is not included in the delivery.
Please check the delivery immediately after
receiving the shipment for apparent damages
due to shipping. Report shipment losses at
once to the carrier and the supplier!

9Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Available Bolt Kits
Size Ordering no. Mounting bolt Torque
TFP025 BK504 4 pcs. M12x100 108 Nm
TFP032 BK529 4 pcs. M16x100 264 Nm
TFP040 BK481 4 pcs. M20x110 517 Nm
TFP050 BK544 4 pcs. M20x130 517 Nm
TFP063 BK545 4 pcs. M30x140 1775 Nm
TFP080 BK546 8 pcs. M24x200 890 Nm
TFP100 BK547 8 pcs. M30x220 1775 Nm
Disassembly
Use of disassembly aid (from nominal size NG50)
First loosen the two xing screws without disas-
sembly aid. Then loosen the two socket screws
SW6 (TFP050: the two ring bolts) with the disas-
sembly aids and turn the straps 90° against the
stop. Fix the socket screws/ring bolts again. Now
loosen the two remaining xing screws alternate-
ly. By turning them against the straps, the valve is
pulled out of the cavity.
Mounting
• Compare valve type (located on the name plate)
with part list resp. circuit diagram.
• The valve may be mounted x or movable in
any direction.
• Verify the mounting surface for the valve. Uneve-
ness of 0.01 mm/100 mm, surface nish of 6.3
µm are tolerable values.
Keep valve mounting surface and work envi-
ronment clean!
• Remove protection plate from the valve mounting
surface
• Check the proper position of the valve ports
and the O-rings.
• Mounting bolts: use property class 12.9, ISO 4762
Insu󰀩cient condition of the valve mounting
surface might create malfunction!
Incorrect mounting resp. bolt torque may
result in abrupt leakage of hydraulic uid on
the valve ports.
Y-port has always to be tied directly and
separately to tank!
90°

10 Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
The connecting cable has to comply to the follow-
ing specication:
Cable type control cable, exible,
7 conductors, overall braid
shield
Cross section min. AWG16
Outer dimension 8...12 mm
Cable length max. 50 m
For cable lengths > 50 m consult Parker.
The connection cable is coupled to the female
connector by solder joints.
Skinning lengths for the connecting cable:
Electrical Connection
The electrical connection of the valve takes place
by one common cable, which is coupled to the
integrated electronic driver by a central connector
assembly.
The connection requires a 6 + PE female connector
EN 175201-804.
Female connector (ordering no. 5004072)
A female connector with metal housing is
required! Plastic made models may create
function problems due to insu󰀩cient EMC-
characteristics.
Do not disconnect cable socket under tension!
Pressure Fluids
The following rules applies for the operation with
various pressure uids:
This information serves for orientation and
does not substitute user tests among the
particular operating conditions. Particularly no
liabiliy for media compatibility may be derived
out of it.
Mineral oil: usable without restriction.
HFC: Choose seal option code N.
HFA Oil-in-water emulsion
HFB Water-in-oil emulsion
HFD Unhydrous uids (Phosphor-Ester)
For operation with the following pressure uids
please consult Parker:
For detailed information concerning pressure
uids note VDMA-document 24317 as well as
DIN 51524 & 51502.
Special gaskets may be available depending on
the utilized uid.
In case of doubt please consult Parker.
Limits of Use
The valve may be operated within the determined
limits only. Please refer to the “technical data“
section as well as to the “characteristic curves“ in
the Parker catalogue MSG11-3500/UK "Hydraulic
Valves Industrial Standard".
Follow the environmental conditions! Unal-
lowable temperatures, shock load, aggresive
chemicals exposure, radiation exposure,
illegal electromagnetic emissions may result
in operating trouble and may lead to failure!
Follow the operating limits listed in the “speci-
cations“ table!

11 Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Wiring Diagram of Supply Voltage
Electrical Interfacing
Supply Voltage
The supply voltage for the valve has to cover the
range of 22...30 V. Valve is de-energized below
19 V. The residual ripple may not exceed 5 % e󰀨.
The applied power supply must comply to
the relevant regulations (DIN EN 61558) and
must carry a CE-mark. The operating voltage
for the valve must be free of inductive surges.
Do not exceed the max. value of 30 V! Higher
voltage can lead to failure of the valve.
The increased inrush current of the valve
should be considered when selecting the
power supply. A stabilized power supply with
overcurrent limiting feature should not be
used. Due to the inrush current of the valve the
current limit circuit may respond prematurely
and create problems during energizing of the
supply voltage.
The operation of the valve is blocked if the
supply voltage polarity is interchanged.
Each valve requires a separate pre-fuse of 4
Amp semi time-lag. Failure to observe this
instruction may create irreparable damage of
valve respectively incorporated system parts.
The backshell nut of the cable gland has to be
tighten with a suitable tool. The target value for
the tightening torque is 4 Nm. Tighten the cap nut
with a torque of 5 Nm after attaching the female
connector on the socket.
Incomplete tightening of backshell nut respec-
tively cap nut may result in undesired release
of the connection as well as degradation of
the water tightness.
When using female connectors of other
manufacturers, the relevant regulations must
be observed.
The cable may only be connected to the female
connector by authorized and qualied person-
nel. A short between individual conductors
resp. to the connector housing, bad soldering
as well as improper shield connection may
result in malfunction and breakdown of the
valve.
The mounting surface of the valve has to be
connected to the earth grounded machine
frame. The earth ground wire from the valve
connecting cable as well as the cable shield
have to be tied to the protective earth terminal
within the control unit. It is necessary to use
a low ohmic potential connection between
control unit and machine frame to prevent
earth loops (cross section AWG 6).

12 Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Command Signal Input
The spool stroke behaves proportional to the com-
mand signal amplitude.
The command input signal needs to be ltered
as well as free of inductive surges and modu-
lations. Due to the sensitivity of the valve a
high signal quality is recommended, this will
prevent malfunction.
Enable Input
A signal voltage enables the actuator drive of the
valve. Continuous operation of the valve requires a
permanent voltage 5...30 V (i.e. the supply voltage).
In case of disabling the signal the valve will reach its
power down position spring-actuated independently
from the command signal value.
The enable function represents no safety ar-
rangement against unwanted valve operation
in terms of rules for accident prevention!
The option 4...20 mA uses the “3.6 mA“
condition as breakdown-information. If the
input signal line is interrupted, an evaluable
failure information is available. In this case the
actuator drive will be switched o󰀨. The drive
will switch on when the input signal reaches
a value of 3.8 mA, it switches o󰀨 when the
command falls below 3.6 mA. This determina-
tion follows the NAMUR-specication NE43.
Diagnostics Output
A diagnostics signal is available. Its voltage repre-
sents the operating condition of the valve.
The output may drive a load of max. 5 mA.
Exceeding of this limit leads to malfunction.
Code com-
mand signal Command signal VCD actuator Diagnostic signal
B
0…+10 V on 0…-10 V
0…-10 V on 0…+10 V
Overload o󰀨 12.5 V
E
0…+20 mA on 0…-10 V
0…-20 mA on 0…+10 V
Overload o󰀨 12.5 V
S
4…12 mA on 0…+10 V
12…20 mA on 0…-10 V
0…3.6 mA o󰀨 Cable break, 12.5 V
Overload o󰀨 12.5 V
Valves NG25 to NG100

13 Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
ProPxD Parameterizing Software
The ProPxD software permits comfortable param-
eter setting for the module electronic. Via the clearly
arranged entry mask the parameters can be noticed
and modied. Storage of complete parameter sets
is possible as well as printout or record as a text
le for further documentation.
The PC software can be downloaded free of charge
at www.parker.com/isde - see page “Support” or
directly at www.parker.com/propxd.
For program installation and software operating
please see operation manual 5715-687. The manual
can be downloaded at www.parker.com/isde – see
page “Support”
Please check periodical for updates.
Cable Specication
Attention! The valve electronic provides no USB
interface, but can only be parametrized via an
RS232C connection. Therefore the usage of
USB standard cables is not allowed and may
result in damaging of valve resp. PC.
Hardware Requirements
• PC with operating system from Windows®XP
upwards
• interface RS232C
• display resolution min. 800 x 600
• connection cable between PC and electronic
module
• storage requirement approx. 40 MB
If your PC has no serial interface according
to RS232 standard you require in addition an
USB-RS232C adapter.
Parametrizing
Ordering code: 40982923
The cover plug has to be re-installed after
completion of the parametrizing work.
Plug for
parametering interface
5. Operating Instructions
Attention! Supply pressure must be ensured
before valve is energized!
To reach the closed position in case of valve
electronic failure, pilot pressure is required.
Solenoid Current Monitoring
If the actuator current time interval exceeds 10
seconds, the actuator is switched o󰀨 to prevent
overheating. For normal operating conditions this
state will not reached, but it may occur with a con-
taminated sluggish valve.
In this case the reason for the contamination
should be repaired (hydraulic uid exchange,
ltration review, valve ushing).
The overcurrent shuto󰀨 condition may be resetted
by temporary disconnection of the enable signal.
The shuto󰀨 of the VCD actuator due to overload
will be indicated via the diagnostics output.

14 Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
LED ashing signals of the valve electronics
enable valve OK: approx. 0.5 Hz (slowly, green)
disable valve OK: approx. 1 Hz (fast, green)
valve error: approx. 10 Hz (very fast, green)
Closer information can be can be displayed via
the ProPxD Parametrier software.
LED
Error code
(additive) Error description
0no errors
1over current
2cable break command signal
4cable break feedback signal
8undervoltage error
16 bus communication error
32 hardware failure
Error codes

15 Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Air Bleeding of Hydraulic System
During initial startup, after an oil change as well as
after the opening of lines or valves the hydraulic
system must be air bleeded.
Filter
The function and lifetime of the valve are strongly
a󰀨ected by the cleanliness of the uid.
Purity level class of 18/16/13 acc. DIN ISO 4406
is required.
Flushing
It is recommended to ush the pipelines by short
circuiting the pressure and return lines. This prevents
the installation dirt from entering the valve.
malfunction at hydraulic load runtime
- generally no function
- high frequent oscillation
- low frequent oscillation
- speed variations at unchanging command
- di󰀨erent speeds depending on travel direction
- speed too low
- drifting without command
possible reasons for malfunction corrective actions
Xhydraulic pump resp. motor defective replace hydraulic pump resp. motor
X X X X X drive overloaded reduce pressure resp. speed, increase valve size
X X X X X X valve contaminated clean pressure uid, lter / ush valve
X X hydraulic uid too viscous / too cold change uid grade, provide operational temperature
X X too low oil level within tank rell pressure uid
X X X lter contaminated clean resp. replace lter
X X X X supply voltage too low keep supply voltage range
Xsupply voltage carries too much ripple reduce ripple
X X command signal too low increase command signal
Xcommand signal carries too much ripple reduce ripple
Xcenter position adjustment incorrect check center position adjustment
X X X X X contacts of central connector contaminated clean contacts / replace plug
Xfeed cable interrupted x feed cable
X X X X X X wiring sequence incorrect correct wiring sequence
X X feed cable without shielding change cable grade
6. Troubleshooting
Basis of troubleshooting is always a systematic
approach.
For suspect of a sluggish spool the valve may
be ushed with clean pressure uid.
Troubleshooting in a hydraulic system requires
detailed knowledge about function and con-
struction of the system. Therefore the work
may exclusively be performed by qualied
personnel.

16 Parker Hannin Corporation
TFP 5715-734UK.indd 24.06.22
2-Way Servo Proportional Valves
Series TFPOperation Manual
Spare Parts / Seal Kits
7. Accessories
The following accessories are available for the
valve series TFP:
Female connector 6+PE ordering code 5004072
Mounting bolts see table on page 9.
Hotline in Europe
Tel.: [phone]
Please direct technical product enquiries to:
Parker Hannin
Manufacturing Germany GmbH & Co. KG
Industrial Systems Division Europe
Gutenbergstr. 38
41564 Kaarst, Germany
E-mail: [email protected].com
Size NBR FPM
TFP025 SK-TFW025AN SK-TFW025AV
TFP032 SK-TFP032AN SK-TFP032AV
TFP040 SK-TFP040AN SK-TFP040AV
TFP050 SK-TFP050AN SK-TFP050AV
TFP063 SK-TFP063AN SK-TFP063AV
TFP080 SK-TFP080AN SK-TFP080AV
TFP100 SK-TFP100AN SK-TFP100AV