Pima Hunter-Pro 832 User manual

Hunter-Pro 832/896/8144
Captain 8
S e c u r i t y S y s t e m s
User Guide

2
HUNTER-PRO Series & CAPTAIN 8 User Guide
Quick Reference
Key
Press for 2 seconds, enter
User code and press the key to...
Press the key for 2 secondsto...
Arm to full mode, disarm
Quickly arm to full mode*
Display the log
-
Temporarily bypass zones
-
Arm to “Home 1” mode
Quickly arm to “Home 1” mode*
Display modes menu
Display the “All Zones”mode for a minute
Set the telephone numbers
-
Arm to “Home 2” mode
Quickly arm to “Home 2” mode*
Set time and date
-
Set the user codes
-
Set the chime per zone
Turn ON/Off the chime feature in chime
zones
Set auto-arming by day and inactivity
-
-
Reset smoke detectors.
Press briefly: display armed partitions
-
Silence the keypad buzzer when it beeps
Display the system‟s name & version
Display the service provider
Initiate system tests
-
-
Display the system‟s name & version
+
Press for 2 seconds: create Panic alarm
+
Press briefly: turn ON/OFF the keypad chime
Factory default codes
Master: 5555
Technician: 1234
Commands marked with an asterisk must be enabled by the Installer.
1
ON/OFF
3
BYPASS
ENTR
ENTR

HUNTER-PRO Series & CAPTAIN 8 User Guide
3
Table of Contents
1INTRODUCTION....................................................................................................5
1.1 Hunter-Pro & Captain 8 mutual features..................................................................5
1.2 Hunter-Pro Series unique features..........................................................................5
1.3 Captain 8 unique features .....................................................................................6
1.4 Safety & Security .................................................................................................6
1.5 Signs and conventions in this guide ........................................................................6
1.6 System codes ......................................................................................................7
1.6.1 The Master code ............................................................................................ 7
1.6.2 User codes ................................................................................................... 7
1.7 The User Menu ....................................................................................................7
1.8 The LCD Keypad ..................................................................................................7
2ARMING & DISARMING THE SYSTEM (KEY #1) .........................................................8
2.1 Arming ...............................................................................................................8
2.1.1 Via the keypad .............................................................................................. 9
2.1.2 Fast arming .................................................................................................. 9
2.2 Disarming ...........................................................................................................9
2.2.1 With the DURESS code................................................................................... 9
3THE SYSTEM LOG (KEY #2) ................................................................................. 10
3.1 Log list sorting options........................................................................................ 10
4TEMPORARILY BYPASSING OPEN ZONES (KEY #3) ................................................. 11
4.1 When arming..................................................................................................... 11
4.2 Prior to arming .................................................................................................. 11
5“HOME 1” & “HOME 2” ARMING MODES (KEYS 4, 7) ............................................... 12
6DISPLAYING TYPES (KEY #5)............................................................................... 13
6.1 Fast 32-zone display........................................................................................... 13
6.2 Scan open zones ................................................................................................ 14
6.3 Disable zone displaying....................................................................................... 15
6.4 Other displaying types ........................................................................................ 15
6.4.1 All Zones .....................................................................................................15
6.4.2 Bypassed Zones ...........................................................................................15
6.4.3 Soaked Zones ..............................................................................................16
6.4.4 Chime Zones ...............................................................................................16
6.4.5 All Zones Status ...........................................................................................16
6.5 Show partition names ......................................................................................... 17
7PHONE NUMBERS, SMS SETTINGS & DIALER TEST (KEY 6)...................................... 17
7.1 Phone numbers.................................................................................................. 17
7.2 SMS messages................................................................................................... 18
7.2.1 A demo SMS message...................................................................................18
7.3 Dialer test ......................................................................................................... 18
8SETTING TIME AND DATE (KEY 8) ........................................................................ 19
9CODES (KEY 9) .................................................................................................. 19
9.1 The Master Code ................................................................................................ 19
9.1.1 Changing the code........................................................................................19
9.2 User codes ........................................................................................................ 20
9.2.1 Adding or change a code ...............................................................................20
9.2.2 Deleting a code ............................................................................................20
9.3 User name ........................................................................................................ 20
9.4 User settings ..................................................................................................... 21
9.5 Disarming Time Frame........................................................................................ 22
9.6 User’s partitions................................................................................................. 22
9.7 Adding a key fob ................................................................................................ 23
9.8 Deleting a key fob .............................................................................................. 23

4
HUNTER-PRO Series & CAPTAIN 8 User Guide
9.9 Adding RFID tag/keychain ................................................................................... 23
9.10 Deleting RFID Tag .............................................................................................. 24
9.11 The DURESS code .............................................................................................. 24
9.12 The Short code .................................................................................................. 24
9.13 The Door code ................................................................................................... 24
10 AUTOMATIC ARMING (KEY 9) ............................................................................... 25
10.1 By day and hour ................................................................................................ 25
10.1.1 Inactivity auto-arming ..................................................................................25
11 THE CHIME FEATURE (KEY #) .............................................................................. 26
11.1 Enabling and disabling the Chime globally ............................................................. 26
12 OTHER TOPICS................................................................................................... 26
12.1 Partitions .......................................................................................................... 26
12.1.1 Examples ....................................................................................................27
12.1.2 Displaying armed partitions ...........................................................................29
12.2 Arming with key, key fob or RFID tag/key chain..................................................... 29
12.2.1 Arming with a key fob ...................................................................................29
12.3 Enabling Remote Upload ..................................................................................... 30
12.4 Names and Characters........................................................................................ 30
12.4.1 Example ......................................................................................................31
12.5 PANIC alarm...................................................................................................... 31
12.6 Resetting Smoke/Fire/Anti-mask detectors............................................................ 32
12.7 Turning the keypad chime ON/OFF ....................................................................... 32
12.8 Comparison between the Hunter-Pro Series models................................................ 32
12.9 Comparison between the Hunter-Pro 896 & Captain 8............................................. 32
13 MANUAL SYSTEM TESTS (BACK KEY) .................................................................... 33
14 REMOTE CONTROL VIA THE PHONE ...................................................................... 33
14.1 Basic mode ....................................................................................................... 34
14.2 Full mode.......................................................................................................... 34
14.2.1 Examples ....................................................................................................35
15 TROUBLESHOOTING ........................................................................................... 36
16 APPENDIX: ZONE LOCATION TABLE ...................................................................... 38

HUNTER-PRO Series & CAPTAIN 8 User Guide
5
1INTRODUCTION
Congratulations on your purchase of the HUNTER-PRO Series and Captain 8 intruder alarm
systems. Much care has been taken in developing these systems, to provide you with
unprecedented peace of mind and security. The user-friendly menu with its advanced features
will professionally help you to protect your premises.
We recommend reading this guide in its entirely in order to familiarize you with the system and
take full advantage of its features.
To assure optimal safety and security, you should perform a system test once a week. See
section 13 for details.
For any further questions, please contact your local PIMA distributor.
1.1 Hunter-Pro & Captain 8 mutual features
Hybrid systems with hardwired and wireless zones;
Operating modes: full or partial, “HOME 1”& “HOME 2”;
Equipped with menu-driven LCD and Graphic keypads, and cost-effective LED keypads;
Optional use of partitions for perimeter zones and separate locations;
Various automatic arming;
Various codes & access options including RFID tag/keychain and key fob;
Authorization settings per user;
Up to four phone numbers to call the Monitoring Station and four to the owner;
Optional disarming time frame per user;
Constant zone, battery and phone line testing;
Communication channels: phone, Long-range Radio, GSM, GPRS, Ethernet;
Various ways to arm and disarm the system: keypad, key switch, RFID tag/keychain,
auto-arming;
Full wireless detectors supervision;
Optional alarm voice messages and listen in microphone;
Various methods for preventing false alarms;
Full log, part is non-volatile.
1.2 Hunter-Pro Series unique features
8 to 32/96/144 zones;
Up to 32/96/144 user codes and RFID tags;
Phone remote control;
Various partitioning options:
Up to 16 partitions;
Up to 8 subsystems.

6
HUNTER-PRO Series & CAPTAIN 8 User Guide
1.3 Captain 8 unique features
8-16 zones;
Up to 30 user codes & RFID tags;
Various partitioning options:
Up to 4 partitions;
Up to 4 subsystems.
1.4 Safety & Security
Both the HUNTER-PRO Series & the Captain 8 systems have been registered in
accordance with the EN60950 standard.
We advise you the following:
The alarm system as well as its wiring should be placed in a hidden and safe location,
protected from rain or moisture.
The alarm system may have hazards of electric shock and fire. Do not try to open the alarm
system‟s case: dangerous high voltages are present inside it. Refer servicing to qualified
personnel only.
This alarm system should be used with 230VAC 50Hz, protected by anti-electric shock
breaker. To prevent electric shocks and fire hazards, do NOT use any other power source.
1.5 Signs and conventions in this guide

Press a key briefly

Press a key for 2 seconds, until confirmation beep sounds
Warning
Note
In programming mode, moves the cursor to the right.
In programming mode, moves the cursor to the left.
Enter, Save
In programming mode, enables („+‟) or disables („-„) a parameter; erase character.
Press briefly: Cancel; Return.
Press for 2 seconds: Silence the keypad chime in faults.
The numbers that are printed above and below the keypad‟s screen stand for zone
numbers and partition numbers.
NEXT
BACK
ENTR
#
END

HUNTER-PRO Series & CAPTAIN 8 User Guide
7
1.6 System codes
1.6.1 The Master code
The Master code is a super user code, with all the access authorizations.
It is mainly used for changing the “Master Code”itself.
1.6.2 User codes
In the Hunter-Pro Series and Captain 8 alarm systems, the User code is the user ID, i.e.,
every user detail and authorization are set under that code.
User codes are assigned separately per user.
A User code can be restricted to only parts of the user menu, i.e., can only set these menus.
1.7 The User Menu
The User menu is where parameters such as Time & Date, User codes and User
authorizations are set.
It is accessed by pressing for 2 seconds and entering a User code. See section
9.4 for restrictions.
By default, entering a User code arms or disarms the alarm system (toggle mode). The
Installer can program the system, so entering the code displays the User menu.
After entering the User menu, the sub-menus are accessed directly, by pressing the
keypad keys. Each key menu is printed above it, e.g. “Time”, “Codes”.
1.8 The LCD Keypad
RXN-400, RXN-410 and RXN-410 RFID are PIMA‟s LCD keypads. They are designed for
maximum simplicity and durability and present decorative design.
The RXN-400 & RXN-410 are identical, except for their screen size: 410‟s is larger.
The screen is made of 2 lines with 16 characters in each. The upper line displays the time
and the date (depending on the display type). Both lines display data regarding the
system, such as events, faults and zone status.
Up to 8 supervised keypads can be connected to the system simultaneously.
The message “Other Keypad in Use” is displayed when another keypad is in
use, or when the system is remotely controlled.
0

8
HUNTER-PRO Series & CAPTAIN 8 User Guide
Figure 1. RXN-410 with the “Fast” display type
2ARMING & DISARMING THE SYSTEM
(KEY #1)
The system can be armed in one of 4 ways:
1. Via the keypad;
2. Automatically;
3. Using Key fob, key switch and RFID tag/keychain;
4. In Hunter-Pro only: by a remote control and via the phone.
As a rule, arming should be carried out only when all the zones are closed, but those on
the exit route, and there are no alarms (e.g., fire, panic) or faults (e.g., low battery):
In the “Fast zone” display type, no zone is indicated with a rectangle _;
In the “Scan open zones” display type, no zone is indicated with “OP” (open).
Zones like exit doors and areas near the keypad are delayed on the exit and the entry, so
whoever arms (or disarms) the system will have enough time to walk from the keypad to the
door, (or the other way, when entering) without triggering any detector.
The Exit & Entry delay times are separate and programmed by the Installer. The Installer
can also program two different Entry delays to different zones.
2.1 Arming
To arm your system, enter a user code (see section 9.4 for restrictions) or the Short code
(a code programmed by the Installer. See section 9.12).
If no zone is open and there are no faults, the Exit delay countdown starts, the keypad
buzzer sounds beeps and the green ARMED LED flashes.You can now exit the premises
and close the door behind you1.
1The Exit delay countdown can start immediately as soon as the final door is closed. Refer to the Installer.

HUNTER-PRO Series & CAPTAIN 8 User Guide
9
When the Exit delay ends, the system becomes armed: the green ARMED LED stops to
flash and stays on, the beeps stop, the message “System Armed” is briefly displayed and
then the date and time are displayed.
2.1.1 Via the keypad
User code ...
The Exit delay time span is set by the Installer.
2.1.2 Fast arming
until the Exit delay starts -OR-Short code ...
Fast/single keystroke arming must be enabled by the Installer.
To set the Short code, see section 9.12.
2.2 Disarming
User code …
To disarm the system, enter a user code.
If an “Access denied” message is displayed, the user may be trying to disarm it outside
her/his “Disarming time frame”. See section 9.5
2.2.1 With the DURESS code
DURESS code …
The DURESS code is a code to be used in threat situations, where you are being forced
to disarm the system. Hence, the code can be used only for disarming.
Entering the DURESS code disarms the system, and in the same time sends a silent alarm
to the Monitoring Station (if you are subscriber) and your phones.
To set the code, refer to section 9.3.
Arming...
Exit Delay 60
System Armed!
1
Arming...
Exit Delay 60
System Armed!
Disarming..
24 AUG 11 19:35
Disarming..
24 AUG 11 19:35

10
HUNTER-PRO Series & CAPTAIN 8 User Guide
3THE SYSTEM LOG (KEY #2)
User code  

The system logs alarms, arming & disarming, zone bypassing, faults, code changing and
other actions, chronologically.
Any action taken by a user is logged with the User name.
Part of the log is non-volatile (see the table on page 32).
3.1 Log list sorting options
A log entry contains, on the upper line, a serial number and the date & time stamp when the
entry (i.e., the event) was logged; the event details appear on the bottom line.
The log has 4 list sorting options: “All the events”, which displays all the log entries in one
list, “Faults only”, “Zone alarms” and “Arming/disarming”.
When you view one of these lists, pressing a number between 0-3, transforms to
corresponding list: 0-“All the events”, 1-“Faults only”, 2-“Zone alarms”, 3-“Arming/disarming”.
Entry example: “Burglary”alarm in zone #4, called “Kitchen”; the two screens are displayed
intermittently.
User Menu
Choose 1,2...
Show:
All Events-0
Show:
Faults Only-1
Show:
Zone Alarms-2
Show:
Arming/Dis.-3
2)1 SEP 11 21:20
Burgl Alarm 4
Serial
number
Zone number
Event type
Date & Time the
event was logged
2)1 SEP 11 21:20
Kitchen
Zone name
~

HUNTER-PRO Series & CAPTAIN 8 User Guide
11
4TEMPORARILY BYPASSING OPEN
ZONES (KEY #3)
Bypassing zones reduces the safety of your protected premises!
It should be used carefully, only if there is no alternative and only for
the shortest possible time.
If you bypass a zone due to a fault, a service technician should
be called;
Beware not to bypass zones unintentionally;
Zones can be bypassed only when the system is disarmed;
A bypassed zone does not sound the alarm when violated, nor does it report the
Monitoring Center.
Temporarily bypassed zones are automatically reinstated when the system is disarmed;
The letter “B” in “Fast zone display" mode indicates a bypassed zone.
A service technician can permanently bypass a zone, such in the case of a zone that no
longer needs to be protected
4.1 When arming
User code to temporarily bypass the open zone/s
.... -OR-to cancel arming 
When you try to arm the system and a 24-hour zone2is open, the keypad sounds beeps
and the message “Open Zone! Press END or Bypass”, with the zone/s details, is displayed
in two intermittently changing screens.
If you do not cancel arming or bypass the open zones, when the Exit delay ends the
system will be armed, but the open zones instantly sound the alarm.
Exit delayed zones are such, so they can be left open until the EXIT delay time ends.
4.2 Prior to arming
You can temporarily bypass zones in advance of arming the system.
As a precaution, there is a time limit, set by the Installer, for a zone to be
bypassed prior to arming. When this time ends and the system has not been
armed yet, the zone is automatically reinstated.
224-Hour zones sound the alarm whenever they are violated, regardless of the system status.
Open Zone! Press
OP:Front door
Bypass or END
OP:Front door
~
3
BYPASS
Arming...
Exit Delay 60
System Armed!
END

12
HUNTER-PRO Series & CAPTAIN 8 User Guide
To temporarily bypass a zone prior to arming:
User code zone number …
approval message is displayed.
For example:
Be aware that a zone is bypassed immediately and stays so, until the
system is disarmed the next time (unless bypass limit time is over).
To reinstate a bypassed zone:
User code zone number …
approval message is displayed.
For example:
5“HOME 1”& “HOME 2”ARMING
MODES (KEYS 4, 7)
“HOME 1” and “HOME 2” are arming modes, in which only some zones are armed, while
others are not: while the armed zones sound the alarm if violated, the disarmed zones can
be occupied at the same time.
Common applications for the Home modes are perimeter detectors and nighttime zones.
The zones included in each Home mode are set by the Installer and require no
hardware installation.
Arming to the Home modes is much like arming to full mode, and there is fast arming
option too.
To arm to “HOME 1” mode : User/Short code
To arm to “HOME 2” mode: User/Short code
3
BYPASS
Zone Number: 1
Entr-Conf #-Rst
ENTR
Bypassed Zone
Back door -14
Zone name Zone number
3
BYPASS
Zone Number: 1
Entr-Conf #-Rst
#
Activated Zone
Back door -14
Zone name Zone number
For HOME1 Arming
Enter Code
Home 1 Arming..
Exit Delay 60
For HOME2 Arming
Enter Code
Home 2 Arming..
Exit Delay 60

HUNTER-PRO Series & CAPTAIN 8 User Guide
13
To arm to the Home modes via the User menu: User code for
“Home 1” or for “Home 2”.
The Exit delay for both Home modes can be cancelled by the Installer.
6DISPLAYING TYPES (KEY #5)
  User code 
Display Type:
Fast Zn. Display

Display Type:
Scan Open Zones

Display Type:
Disable Zn. Disp

Display Type:
All Zones

Display Type:
Display Bypass Z

Display Type:
Display Soak Zn.

Display Type:
Display Chime Zn

Display Type:
All Zones Status

Display Type:
Show Part Name
Your keypad has few options for displaying information on zones, alarms, faults etc.
There are two basic displaying types: single screen and scrolling.
Other types display various information for a minute, before they return to one of the
basic types.
Zone names are programmed by the Installer.
6.1 Fast 32-zone display
  User code 
Display Type:
Fast Zn. Display

This display type is best used in systems with up to 32 zones. Each line displays 16 zones.
The zones are displayed in a single screen, with their status represented by signs and letters.
Each sign appears next to the related zone number, which is printed above & bellow the
keypad screen. See Figure 1.
If the number of zones is no more than 16, information in the top line includes time, date
and system status. If the system is configured with more than 16 zones, this information
will not be displayed, but the other 16 zones.
Figure 1. Fast zone mode with 16 zones
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
NEXT
ENTR
15 OCT 10PS08:53
-F- -B----_ ---- _ -
1 2 3 4 5 6 7 8 9 10 1 1 12 1 3 14 1 5 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Date Time
System
indicators
First 32
zones
Fault
(zone #2)
Bypassed
zone (#6)
Closed
zone (#12)
Open
zone (#15)

14
HUNTER-PRO Series & CAPTAIN 8 User Guide
The system indicators on the top line (between the time and the date) are:
Indicator
Description
P
The system is communicating or testing the phone line
T
The system is communicating over the Radio
R
The RELAY output is active
S
The SIREN output is active
The zone status indicators are:
Indicator
Description
-
Closed (not triggered) zone
_
Open (triggered) zone. If the zone has more than one status (e.g., it is
open and alarming), the indications are displayed intermittently.
A
Alarmed zone: the zone was violated when the system was armed, or is
alarming now.
B
Bypassed zone
C
Chime zone
F
Zone failure (disconnection) or a TAMPER switch is open
L
Low battery in a wireless detector
O
Opened 24-hour zone or armed partition. Press to display the
armed partitions.
S
Short in the zone's wires
T
The zone is in soak (test) mode
V
A wireless detector is not responding
6.2 Scan open zones
User code 
Display Type:
Scan Open Zones

The system continuously scans the zones and the system‟s status, and displays open
zones, faults and alarms.
The information is displayed in scrolling mode.
For example:
#
5
NEXT
ENTR
14 SEP 10 07:15
Low Battery
Zone #13 is open
7 JUN 10 05:33
OP:Zone 13
Low battery

HUNTER-PRO Series & CAPTAIN 8 User Guide
15
The zones‟ status indicators are:
Indicator
Description
OP
Open zone
AL
The zone was violated when the
system was armed, or is alarming now.
BP
Bypassed zone
FL
Zone Cut
SH
Zone Short
SV
Zone supervision
LB
Wireless zone low battery
AM
Anti-mask zone
6.3 Disable zone displaying
User code X2 
The zones‟ status is not displayed, only alarms and faults (if there are any).
6.4 Other displaying types
to the next displaying types.
The other types display various information. After pressing the information is
displayed for a minute.
See the display types menu in the beginning of section 6.
6.4.1 All Zones
User code   X3 zone number
repeatedly
The properties of every programmed zone - name, partitions and type - are displayed
when pressing repeatedly.
6.4.2 Bypassed Zones
User code   X4 to display other
bypassed zones - OR - repeatedly to display the zone‟s name, partitions and type.
Permanently and temporarily bypassed zones are displayed in this type.
Permanently bypassed zones are set by the Installer.
Temporarily bypassed zones will be automatically reinstated the next time the system
is disarmed.
5
NEXT
Display Type:
Disable Zn. Disp
ENTR
NEXT
ENTR
5
NEXT
Display Type:
All Zones
ENTR
ENTR
ENTR
5
NEXT
Display Type:
Display Bypass Z
NEXT
ENTR

16
HUNTER-PRO Series & CAPTAIN 8 User Guide
6.4.3 Soaked Zones
User code   X5 to display other
soaked zones - OR - repeatedly to display the zone‟s name, partitions and type.
A zone is set as Soak (test) zone by the Installer/Service technician, when it is
repeatedly faulty.
Soak zones, as well as soak period (up to a week), are set by the Installer/Service technician.
Soak zones are automatically reinstated when the soak period is over.
6.4.4 Chime Zones
User code   X6 to display other
chime zones - OR - repeatedly to display the zone‟s name, partitions and type.
Chime zones trigger the keypad chime when opened.
6.4.5 All Zones Status
User code X7 
....
This type is intended to display the status of all the programmed zones quickly.
It is design the same as the “Fast zone” type, 10 zones in each line, and 20 in every
screen. See section 6.1 for details on the signs.
In the above screenshots, the first screen displays the status of zones 1 - 10 and 11 - 20.
Statuses for example are:
Zone #1: chime zone.
Zones #2-3: closed zones.
Zones #4-6: open zones.
Zone #7: chime zone.
Zone #8: bypassed zone.
Zones #9-10: closed zones.
Zone #12: zone fault.
Zone #15: zone activated the siren.
Zone #22: chime zone.
Zone #34: bypassed zone.
5
NEXT
Display Type:
Display Soak Zn.
NEXT
ENTR
5
NEXT
Display Type:
Display Chime Zn
NEXT
ENTR
5
NEXT
Display Type:
All Zones Status
ENTR
C--___CB-- 1 ->10
-F- -S_---- 11->20
NEXT
-C- _ ----- 21->30
---B- _ --- 31->40
NEXT
- _ -- 141>

HUNTER-PRO Series & CAPTAIN 8 User Guide
17
6.5 Show partition names
User code   
This is a toggle display type: when it is enabled, the names of the partition/s (see section
12.1 for details) this keypad is allocated to, are constantly displayed.
To disable this mode, repeat the process.
This mode requires the “Scan Open Zones” display mode to be selected first.
7PHONE NUMBERS, SMS SETTINGS &
DIALER TEST (KEY 6)
User code 
Key #6 has three sub-menus:
“Edit Numbers”, to set your phone numbers for receiving alarms and other messages
from the system;
“SMS Settings”, to set which of your phones will receive SMS messages instead of
alarm messages;
“Test dialer”, for testing the numbers you have programmed (without triggering
the sirens);
7.1 Phone numbers
User code 
phone #1 
Priv.Phn 2<Del=#
or ....
The HUNTER-PRO Series & the Captain 8 have an integrated phone dialer, that can call up
to 4 numbers and sound an alarm, or send SMS alert or sound a recorded message.
When an alarm is set off, the dialer attempts to call each number twice (i.e., a total of 8
attempts) 3.; when the call is answered, the system sounds a Hi/Lo siren, or a voice message4.
To set a number, enter it and 
To use “+”, “*”, “#”and “P”for one second delay: repeatedly
3SMS messages are sent only once to each number.
4This feature requires the purchasing of the VU-20 voice module.
5
BACK
Display Type:
Show Part Name
ENTR
Edit Numbers
ENTER/NEXT/BACK
Priv.Phn 1<Del=# Priv.Phn 4<Del=#
ENTR
6
PHONES
ENTR . . .
NEXT
Edit Numbers
ENTER/NEXT/BACK
SMS Settings
ENTER/NEXT/BACK
1234
---- SMS Options
6
PHONE
ENTR
NEXT
NEXT
Edit Numbers
ENTER/NEXT/BACK
Dialing...
5554444
Test Dialer
Select T.No. 1-4
Testing Line..H1
….Sending... ….Finished OK!
1
BACK
6
PHONE
Edit Numbers
ENTER/NEXT/BACK
Priv.Phn 1<Del=# Priv.Phn 4<Del=#
ENTR
6
PHONES
ENTR . . .
ENTR
Edit Numbers
ENTER/NEXT/BACK
Priv.Phn 1<Del=# Priv.Phn 4<Del=#
ENTR
6
PHONES
ENTR . . .
ENTR
NEXT
Edit Numbers
ENTER/NEXT/BACK
Priv.Phn 1<Del=# Priv.Phn 4<Del=#
ENTR
6
PHONES
ENTR . . .
ENTR
*

18
HUNTER-PRO Series & CAPTAIN 8 User Guide
The dialer aborts the dialing attempts in the following cases:
The system is disarmed.
All numbers were dialed, each number twice (i.e., no call was answered).
In HUNTER-PRO Series only, a remote control command is received. See section 14.1.
7.2 SMS messages
User code 
to select a number (set it to “+”). to move to the
next numbers.
Text messages are an alternative way for you to receive alarms and faults reports.
The numbers 1-4 stand for the corresponding phone numbers.
A phone number that is set here to receive SMS messages will not receive the siren alarm.
For example, phone #2 will receive SMS messages.
Sending SMS messages requires the purchasing of the SMS-100 module or the GSM-200
cellular module.
7.2.1 A demo SMS message
The details in the SMS messages are all taken from the system log.
In this figure, the time and date indicate when the event was registered in the log, and not
when the message was sent.
7.3 Dialer test
User code 
( / / ) ...
... ...
Use the Dialer test menu to check the programmed phone numbers.
NEXT
Edit Numbers
ENTER/NEXT/BACK
SMS Settings
ENTER/NEXT/BACK
1234
---- SMS Options
6
PHONE
ENTR
NEXT
ENTR
Edit Numbers
ENTER/NEXT/BACK
SMS Settings
ENTER/NEXT/BACK
1234
---- SMS Options
6
PHONE
ENTR
NEXT
NEXT
1234
-+-- SMS Options
NEXT
NEXT
Edit Numbers
ENTER/NEXT/BACK
Dialing...
5554444
Test Dialer
Select T.No. 1-4
Testing Line..H1
….Sending... ….Finished OK!
1
BACK
6
PHONE
1
ON/OFF
3
BYPASS

HUNTER-PRO Series & CAPTAIN 8 User Guide
19
Press a number between 1 and 4 to call the corresponding programmed number.
If a call is not received, check that the number is correct; if it is, call a service technician.
During the test, the system displays the communication process, as displayed above.
8SETTING TIME AND DATE (KEY 8)
User code time in the following format: hh:mm
date in the following format: dd:mm:yy 
/ to move to the left and right.
To correct data, and start over.
You must keep the system‟s clock accurate at all times, for maintaining a detailed log and
for functions such as user disarming time frame.
If the clock is not set, a “Clock Not Set” error is displayed and the keypad beeps.
9CODES (KEY 9)
Codes in the Hunter-Pro Series and Captain 8 systems are made of 4-6 digits (except for
the Short code).
Duplicate codes or codes that start with same two digits as the Short code are not allowed.
Codes are concealed with asterisks and cannot be revealed or restored in any way.
9.1 The Master Code
The default Master (5555) should be replaced immediately after installation
(see how in this section).
The Master code is a super user code, with all access authorizations. See section 1.6.1 for
more details.
Its main use is changing the Master code itself.
9.1.1 Changing the code
Master code 
4-6 digits number 
Hour
00:00
ENTR
Day Month Year
01 01 12
ENTR
END
NEXT
BACK
END
User Menu
Choose 1,2...
9
CODES
Master Code
ENTER/NEXT/END
ENTR
Master Code
****** (4-6)
ENTR

20
HUNTER-PRO Series & CAPTAIN 8 User Guide
The “Master code” menu is visible only when entering the User menu with the Master code.
Therefore, to change the code, you can only use the Master code.
When entering the User menu with a User code and pressing “9”, the “User Codes” menu
is displayed.
9.2 User codes
See section 1.6.2 for details about user codes.
9.2.1 Adding or change a code
User code 
User 1 (1)
ENTER/NEXT/END

User number 
Entr/Change Code
ENTER/NEXT/END

User 1
****** (4-6)
4-6 digit number

An asterisk (*) appears to the right of the user‟s name, notes the user code has been
assigned to this user. For example, “Linda” is user number 16:
9.2.2 Deleting a code
User code 
User 1 (1) *
ENTER/NEXT/END

User number 
Delete Code
ENTER/NEXT/END

Once a code is deleted, the asterisk is deleted too and the code is available to be used for
another user.
9.3 User name
User code 
user number X2
User Name
ENTER/NEXT/END

User Name 1
User 1

name (up to 8 characters) 
9
CODES
User Codes
ENTER/NEXT/END
ENTR
ENTR
ENTR
ENTR
Linda (16 ) *
ENTER/NEXT/END
9
CODES
User Codes
ENTER/NEXT/END
ENTR
ENTR
NEXT
ENTR
Code deleted
Press END
END
9
CODES
User Codes
ENTER/NEXT/END
ENTR
User 1 (1) *
ENTER/NEXT/END
ENTR
NEXT
ENTR
ENTR